Home › Drivetrain › K313 (MULTIDRIVE / CVT) › FRONT DIFFERENTIAL OIL SEAL
RM32H0E _52 Drivetrain _059624 K313 MULTIDRIVE / CVT _0299370 FRONT DIFFERENTIAL OIL SEAL A

K313 MULTIDRIVE / CVT  FRONT DIFFERENTIAL OIL SEAL  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front differential oil seal removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)

PROCEDURE

Hide 51441 1.REMOVE NO. 1 ENGINE UNDER COVER

Hide 51444A 2.REMOVE REAR ENGINE UNDER COVER LH

Hide 51443C 3.REMOVE REAR ENGINE UNDER COVER RH

Hide 4.DRAIN CONTINUOUSLY VARIABLE TRANSAXLE FLUID

a.
C362025

Remove the refill plug and gasket from the continuously variable transaxle assembly.


b.
C362026

Using a 6 mm hexagon socket wrench, remove the overflow plug and gasket from the continuously variable transaxle assembly.


c.
C364033C01
2.365,0.656 2.583,0.844 true 2.198,0.51 2.51,0.708 0.313,0.198 10 false *1
*1 No. 1 Transmission Oil Filler Tube


Using a 6 mm hexagon socket wrench, remove the No. 1 transmission oil filler tube from the transaxle oil (CVT) pan sub-assembly.

HINT:

Removing the No. 1 transmission oil filler tube will drain all oil in the transaxle oil (CVT) pan sub-assembly.



d.

Using a 6 mm hexagon socket wrench, install the No. 1 transmission oil filler tube to the transaxle oil (CVT) pan sub-assembly.

Torque:
1.7 N*m (17 kgf*cm, 15 in.*lbf)


e.

Using a 6 mm hexagon socket wrench, temporarily install the overflow plug and gasket to the continuously variable transaxle assembly.

HINT:

Reuse the old gasket as the overflow plug will be removed again to adjust the fluid level.



f.

Temporarily install the gasket and refill plug to the continuously variable transaxle assembly.

HINT:

Reuse the old gasket as the refill plug will be removed again to adjust the fluid level.



Hide 5.REMOVE FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)

Hide 6.REMOVE FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)

Hide 43420H 7.REMOVE FRONT DRIVE SHAFT OIL SEAL LH

a.
C160542N04
2.24,1.333 2.719,2.24 2.719,2.24 2.854,2.24 true 1.125,3.125 1.24,3.125 1.24,3.125 1.24,2.531 false 0.823,3.052 1.229,3.26 0.406,0.208 10 false SST 2.917,2.156 3.354,2.385 0.438,0.229 10 false SST

Using SST, remove the front drive shaft oil seal LH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43410M 8.REMOVE FRONT DRIVE SHAFT OIL SEAL RH

a.
C160541N04
0.906,0.604 1.427,0.604 false 2.688,2 2.688,1.75 2.688,1.75 2.792,1.75 false 0.615,0.521 1.052,0.771 0.438,0.25 10 false SST 2.833,1.667 3.323,2 0.49,0.333 10 false SST

Using SST, remove the front drive shaft oil seal RH from the continuously variable transaxle assembly.

SST
09308-00010  

NOTICE:

Do not damage the continuously variable transaxle assembly.



Hide 43420H 9.INSTALL FRONT DRIVE SHAFT OIL SEAL LH

a.

Apply MP grease to the lip of a new front drive shaft oil seal LH.


b.
C269119N01
0.531,1.365 0.885,1.531 false 2.125,1.167 3.01,0.885 false 1.375,2.969 1.729,2.563 false 0.25,1.281 0.708,1.479 0.458,0.198 10 SST 3.052,0.792 3.427,0.958 0.375,0.167 10 SST 1.104,2.938 1.51,3.115 0.406,0.177 10 SST

Using SST and a hammer, install the front drive shaft oil seal LH to the continuously variable transaxle assembly.

SST
09387-00010  
09950-70010  (09951-07150)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal LH in the correct direction.

·

Make sure to install the front drive shaft oil seal LH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal LH.




Hide 43410M 10.INSTALL FRONT DRIVE SHAFT OIL SEAL RH

a.

Apply MP grease to the lip of a new front drive shaft oil seal RH.


b.
C160540N04
2.24,0.917 1.833,1.104 1.833,1.104 2.146,0.708 false 2.719,2.271 2.719,2.615 false 1.531,1.042 1.854,1.219 0.323,0.177 10 false SST 2.604,2.625 2.927,2.802 0.323,0.177 10 false SST

Using SST and a hammer, install the front drive shaft oil seal RH to the continuously variable transaxle assembly.

SST
09554-14010  
09950-70010  (09951-07100)

Standard Depth:

-0.5 to 0.5 mm (-0.0197 to 0.0197 in.)


NOTICE:
·

Be sure to install the front drive shaft oil seal RH in the correct direction.

·

Make sure to install the front drive shaft oil seal RH as specified, otherwise malfunctions such as a fluid leak will occur.

·

Do not damage the lip of the front drive shaft oil seal RH.




Hide 11.INSTALL FRONT DRIVE SHAFT ASSEMBLY (for TMC Made)

Hide 12.INSTALL FRONT DRIVE SHAFT ASSEMBLY (for TMMT Made)

Hide 13.ADD CONTINUOUSLY VARIABLE TRANSAXLE FLUID

Hide 14.INSPECT FOR FLUID LEAK

Hide 51444A 15.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 16.INSTALL REAR ENGINE UNDER COVER RH

Hide 51441 17.INSTALL NO. 1 ENGINE UNDER COVER