If the engine stalls or fails to start while stop and start control is operating, DTC P1603 will be stored. Using the GTS, the freeze frame data recorded the moment the DTC is stored can be read. Serviceability has been enhanced by enabling the cause of an engine stall or engine start failure which occurred while stop and start control was operating to be checked using the freeze frame data.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Warning Indicate | Memory |
|---|---|---|---|---|---|
| P1603 | Engine Stall History | Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·
Engine stopped by stop and start control and engine hood opened ·
engine hood courtesy switch (hood lock assembly): Engine hood opened and mode changed to "stalled"*1 Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·
Engine stopped by stop and start control and collision or low battery voltage detected ·
Collision detection signal received from the airbag sensor assembly and mode changed to "stalled"*1 Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·
Engine being restarted by stop and start control and collision detected ·
Collision detection signal received from the airbag sensor assembly and mode changed to "stalled"*1 Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·
Engine being restarted by stop and start control and restart fails ·
Using the NE signal, complete combustion is identified 0.6 seconds after the engine stop judgment*2 was made or complete combustion does not occur even after the starter assembly has operated for a certain amount of time (NE signal is normal). Both of the following conditions are met for 0.5 seconds or more (1 trip detection logic):
·
Engine being restarted by stop and start control and restart fails ·
Engine speed signal from the ECM not received via CAN communication (NE signal is abnormal*3). Detection Conditions: Always Sensors/components used for detection: engine hood courtesy switch (hood lock assembly), neutral position switch airbag sensor assembly, battery, crank position sensor, STA signal circuit, ECM |
·
Wire harness or connector ·
Engine hood courtesy switch (Hood lock assembly) ·
CAN communication system ·
Airbag system ·
SFI system ·
Starter assembly ·
Engine stop and start ECU |
Does not come on | DTC stored |
*1: The mode "stalled" represents a state in which engine restart is prohibited/canceled due to a collision being detected or the engine hood being opened and restart is not preferable. In this situation, "IG" is displayed for the Data List item [Stop&Start of Eng State]. If the mode changes to "IG", engine start by stop and start control is prohibited and the engine can only be started by operating the ignition or starter switch assembly.
*2: Engine stop judgment is performed to judge whether the engine is stopped completely. The engine stop and start ECU judges that the engine is stopped when it does not receive an engine speed signal (NE signal) from the ECM for 0.6 seconds or more.
*3: The engine stop and start ECU stores DTC P0335.
Refer to Hood Courtesy Switch Circuit.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>Engine Hood Courtesy Switch Circuit
Refer to DTC P0617.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>P0617
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
When the starter assembly is replaced, "ST relay" must be also replaced.
After replacing the starter assembly, perform initialization of the number of starter operations stored in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION
Inspect the fuses for circuits related to this system before performing the following procedure.
If other DTCs are output, perform troubleshooting for this DTC first.
Unlike other DTCs that are stored due to a malfunction in parts, circuits or systems, DTC P1603 allows determination of a malfunctioning part according to problem symptoms and freeze frame data related to a problem recognized by the customer. As this DTC may be stored due to an operation by the customer, it is not necessary to service the vehicle unless the customer recognized a problem. Clear the DTCs and return the vehicle to the customer.
Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA
Stop and Start Control Mode Transition:
*1: Engine stop conditions are met.
*2: Engine stop judgment is determined.
*3: Engine start conditions are met before the engine is judged as stopped.
*4: Engine start conditions are met.
*5: Engine determined to be started (engine speed reaches a specified rpm).
*6: Collision detected or engine hood opened and mode changed to "stalled".
*7: 0.6 seconds elapse after engine stop judgment is established.
*8: Engine is started using the ignition or starter switch assembly.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes
Read the DTCs.
| Result | Proceed to |
|---|---|
| SFI system DTCs are not output | A |
| SFI system starting malfunction circuit DTC is output and starter assembly does not operate | |
| SFI system starting malfunction circuit DTC is output and starter assembly operates | B |
| DTCs other than SFI system starting malfunction circuit DTC are output |
According to the display on the GTS, check the freeze frame data item [Cranking Time] in the sets of freeze frame data.
If the value of [Cranking Time] is approximately 3 seconds, the stop and start control system or starter system may be malfunctioning.
If the value of [Cranking Time] is small (approximately 0.5 seconds or less: the minimum value varies depending on the model), the SFI system may be malfunctioning.
The Data List item [Cranking Time] indicates the length of time starter operation is requested by the engine stop and start ECU. If the engine speed exceeds the specified value, the engine stop and start ECU cancels its start request.
A
B
The freeze frame data is cleared when DTCs are cleared. Be sure to make a note of necessary data in advance.
Using the time-series freeze frame data, confirm the freeze frame data recorded the moment the DTC was stored and after the DTC was stored. This information can be useful when troubleshooting.
According to the prompts on the GTS screen, read the time-series freeze frame data to confirm the vehicle conditions when an engine stall occurred while stop and start control was operating.
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA
Check the freeze frame data for engine stall history and engine start failure.
| Tester Display | Result | Proceed to |
|---|---|---|
| Engine Stall History during S&S (Hood Open) | Yes | A |
| Engine Stall History during S&S (Collision or Battery Low) | Yes | B |
| Engine Stall History during Engine Starting (Collision) | Yes | |
| Engine Start Fail | Yes | C |
A
B
C
Before performing this step, check that the engine hood can be opened by pulling the hood lock control cable.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.
According to the display on the GTS, read the Data List.
| Tester Display |
|---|
| Hood Courtesy Switch |
| Tester Display | Condition | Normal Condition |
|---|---|---|
| Hood Courtesy Switch | Engine hood closed | ON |
| Engine hood open | OFF |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the engine hood courtesy switch (hood lock assembly).
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>REMOVAL
Inspect the engine hood courtesy switch (hood lock assembly).
Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A8 engine hood courtesy switch (hood lock assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A8-2 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the A62 engine stop and start ECU connector.
Disconnect the A8 engine hood courtesy switch (hood lock assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-7 (BNT1) - A8-1 (+) | Always | Below 1 Ω |
| A62-7 (BNT1) - Body ground and other terminals | Always | 10 kΩ or higher |
| A8-1 (+) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check if the vehicle was in a collision when the engine stalled.
| Result | Proceed to |
|---|---|
| Vehicle was in collision when engine stalled | A |
| Vehicle was not in collision when engine stalled | B |
When "Engine Stall History during S&S (Collision or Battery Low)" or "Engine Stall History during Engine Starting (Collision)" is stored:
This may have been stored because the vehicle was in a collision or a collision detection signal was input while stop and start control was operating.
A
B
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Disconnect the A62 engine stop and start ECU connector.
Disconnect the A38 ECM connector.
Remove the ST relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A62-21 (STA) - ST relay holder 2 | Always | Below 1 Ω |
| A38-29 (STA) - ST relay holder 2 | Always | Below 1 Ω |
| A62-21 (STA) - A38-29 (STA) | Always | Below 1 Ω |
| A62-21 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| A38-29 (STA) - Body ground and other terminals | Always | 10 kΩ or higher |
| ST relay holder 2 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay holder 1 - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block.
| *1 | No. 1 Engine Room Relay Block |
| *a | ST Relay Terminal |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay holder 5 - Body ground | Always | 9.5 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Starter Assembly |
| *a | C67-1 |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C67-1 - Body ground | Always | 9.5 to 14 V |
Before performing this step, check that the starter assembly connector C67 is not disconnected or loose.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the ST relay from the No. 1 engine room relay block.
Disconnect the C35 starter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| ST relay terminal 3 - C35-1 (ST) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the ST relay.
Click hereEngine / Hybrid System>8NR-FTS (STARTING)>RELAY>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the starter assembly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG