Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2016.10–2018.05
RM32H0E _59 Vehicle Exterior _060017 DOOR / HATCH _0295667 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 75978H 2.INSTALL REAR DOOR LOWER OUTSIDE STRIPE

Hide 75766A 3.INSTALL REAR DOOR REAR WINDOW FRAME MOULDING

Hide 75764A 4.INSTALL REAR DOOR UPPER WINDOW FRAME MOULDING

Hide 75742 5.INSTALL REAR DOOR OUTSIDE MOULDING

Hide 75076 6.INSTALL REAR DOOR OUTSIDE MOULDING SUB-ASSEMBLY

Hide 67003C 7.INSTALL REAR DOOR PANEL CUSHION

a.
B458171

Engage the claws to install the 2 rear door panel cushions.


Hide 86160B 8.INSTALL REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

Hide 86262D 9.INSTALL REAR DOOR SPEAKER COVER (w/o Rear Speaker)

a.
B458194N01
0.771,1.594 0.885,1.76 0.115,0.167 10 true 3 0.833,0.083 0.948,0.25 0.115,0.167 10 true 1 2.51,0.5 2.625,0.667 0.115,0.167 10 true 2

Engage the guides to temporarily install the rear door speaker cover.


b.

Using an air riveter or a hand riveter, install the front speaker cover with 3 new rivets in the order shown in the illustration.

NOTICE:
·
B125583C26
1.875,1.271 1.875,1.823 true 1.302,0.292 1.76,0.719 false 1.115,0.146 1.427,0.302 0.313,0.156 10 false *a 1.823,1.875 2.135,2.094 0.313,0.219 10 false *b 2.063,0.063 2.385,0.302 0.323,0.24 10 false *c
*a Riveter
*b Mandrel
*c Incorrect


Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

·
B125584C09
1.438,0.448 1.156,0.448 false 1.458,1.417 1.219,1.417 false 1.479,0.365 1.802,0.604 0.323,0.24 10 false *a 2.198,0.125 2.51,0.365 0.313,0.24 10 false *b 2.052,1.146 2.365,1.385 0.313,0.24 10 false *b 1.531,1.313 1.854,1.552 0.323,0.24 10 false *a
*a Riveter
*b Incorrect


Confirm that the rivets are seated properly against the moulding.

·

Do not tilt the riveter when installing the rivet to the moulding.

·

Do not leave any space between the rivet head and moulding.

·
B125585C10
1.135,0.771 1.396,0.771 false 1.438,0.667 1.75,0.938 0.313,0.271 10 false *a 2.01,0.188 2.344,0.469 0.333,0.281 10 false *b
*a Riveter
*b Incorrect


Do not leave any space between the moulding and door frame. Firmly hold the 2 items together while installing the rivet.




c.
B458192

Connect the connector.


Hide 67837C 10.INSTALL REAR DOOR DUST PROOF SEAL

a.
B458172

Install the 3 rear door dust proof seals.


Hide 69060A 11.INSTALL REAR DOOR LOCK WITH MOTOR ASSEMBLY

Hide 69240 12.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B458177

Engage the guide to connect the No. 1 rear door lock remote control cable assembly.


b.
B458215

Engage the claws to install the rear door outside handle assembly.


c.

Install the 3 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.
B458168

Connect the No. 1 rear door lock remote control cable assembly to the clamps.


Hide 69227L 13.INSTALL REAR DOOR OUTSIDE HANDLE COVER

a.

Clean the rear door outside handle assembly surface.


b.

Remove the release paper from the face of the rear door outside handle cover.


c.
B458167C02
0,0 0,0 false
V100155

Double-sided Tape


Engage the clips and guide to install a new rear door outside handle cover.


d.

Press the double-sided tape area of the rear door outside handle cover.


Hide 75740 14.INSTALL REAR DOOR BELT MOULDING ASSEMBLY

Hide 68189 15.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP

a.
B458166

Install the rear door quarter window weatherstrip to the rear door quarter window glass.


Hide 68124B 16.INSTALL REAR DOOR QUARTER WINDOW GLASS

a.
B458182C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door quarter window glass with rear door quarter window weatherstrip as shown in the illustration.


Hide 17.INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.


b.
B458164C02
1.938,0.573 2.354,0.156 true 2.417,0.063 2.604,0.26 0.188,0.198 10 true *a 1.563,1.542 1.771,1.74 0.208,0.198 10 true 1 2.771,0.198 2.979,0.396 0.208,0.198 10 true 2 2.719,1.313 2.927,1.51 0.208,0.198 10 true 3 1.479,0.135 1.688,0.333 0.208,0.198 10 true 4
*a Temporary Bolt


Temporarily install the temporary bolt to the rear door window regulator sub-assembly.


c.

Temporarily install the rear door window regulator sub-assembly with the 3 bolts.


d.

Tighten the temporary bolt and 3 bolts to install the rear door window regulator sub-assembly.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



e.

Connect the connector.


Hide 68152C 18.INSTALL REAR DOOR GLASS RUN

a.
B458162

Install the rear door glass run.


Hide 67674A 19.INSTALL REAR DOOR FRAME GARNISH

a.
B458163

Engage the guides to install the rear door frame garnish.


Hide 69975A 20.INSTALL REAR DOOR GLASS CHANNEL FILLER (for LED Type Turn Signal Light)

a.

Apply soapy water to a new rear door glass channel filler.


b.
B458178C01
0.5,0.75 0.813,0.917 false 3.052,0.917 3.25,1 false 1.375,0.177 1.688,0.333 0.313,0.156 10 false *A 2.042,0.177 2.354,0.333 0.313,0.156 10 false *B 3.25,0.906 3.417,1.073 0.167,0.167 10 false *a 0.313,0.656 0.479,0.823 0.167,0.167 10 false *a 0.823,0.313 1.135,0.469 0.313,0.156 10 false A 2.958,0.313 3.271,0.469 0.313,0.156 10 false B
*A Front Side
*B Rear Side
*a Edge of curved surface


Install the rear door glass channel filler to the rear door glass sub-assembly at position shown in the illustration.

Standard Dimension
Area Measurement
A 10 mm (0.394 in.)
B 10 mm (0.394 in.)


Hide 69906B 21.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY (for LED Type Turn Signal Light)

a.

Apply soapy water to the channel filler side of the rear door glass channel sub-assembly.


b.
B458179C01
0.396,0.75 0.813,0.917 false 3.052,0.906 3.219,0.99 false 1.375,0.177 1.688,0.333 0.313,0.156 10 false *A 2.052,0.167 2.365,0.323 0.313,0.156 10 false *B 3.26,0.896 3.427,1.063 0.167,0.167 10 false *a 0.219,0.646 0.385,0.813 0.167,0.167 10 false *a 0.823,0.323 1.135,0.479 0.313,0.156 10 false A 2.969,0.323 3.281,0.479 0.313,0.156 10 false B
*A Front Side
*B Rear Side
*a Edge of curved surface


Using a plastic hammer, install the rear door glass channel sub-assembly to the position shown in the illustration.

Standard Dimension
Area Measurement
A 10 mm (0.394 in.)
B 10 mm (0.394 in.)

NOTICE:

To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.



Hide 68104 22.INSTALL REAR DOOR GLASS SUB-ASSEMBLY

a.
B458180C01
0,0 0,0 false
V113147

Install in this Direction (1)
V113148

Install in this Direction (2)


Insert the rear door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the rear door glass sub-assembly.



b.
B458181C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door glass sub-assembly to the rear door window regulator sub-assembly as shown in the illustration.


Hide 67408F 23.INSTALL REAR DOOR WINDOW REAR LOWER FRAME SUB-ASSEMBLY

a.
B458155

Temporarily install the rear door window rear lower frame sub-assembly with the 2 bolts.


b.

Install the screw.


c.

Tighten the 2 bolts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


d.

Connect the rear door glass run.


Hide 67868D 24.INSTALL REAR DOOR WEATHERSTRIP

a.

Clean the rear door panel.


b.

Remove the release paper from a new rear door weatherstrip.


c.
B458157C04
2.969,0.573 3.146,0.333 true 3.208,0.177 3.427,0.375 0.219,0.198 10 false *a
*a Clip (A)
V100155

Double-sided Tape


Engage the clip (A) and other clip to install the rear door weatherstrip.


d.

Press the double-sided tape area of the rear door weatherstrip.


Hide 68640A 25.INSTALL REAR DOOR CHECK ASSEMBLY

a.

Apply MP grease to the sliding parts of the rear door check assembly.


b.

Clean the bolt hole in the vehicle body.


c.

Clean the threads of the bolt (A).


d.

Apply adhesive to the threads of the bolt (A).

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



e.
B458156C01
3.208,1.333 3.375,1.5 0.167,0.167 10 true *a 1.885,0.5 2.052,0.667 0.167,0.167 10 true *b 1.854,1.51 2.021,1.677 0.167,0.167 10 true *b
*a Bolt (A)
*b Bolt (B)


Install the rear door check assembly with the bolt (A) and 2 bolts (B).

Torque:
Bolt (A) : 30 N*m (306 kgf*cm, 22 ft.*lbf)
Bolt (B) : 5.5 N*m (56 kgf*cm, 49 in.*lbf)


Hide 67842E 26.INSTALL REAR DOOR SERVICE HOLE COVER

a.
B458183C01
2.875,2.781 2.958,2.615 true 2.948,0.417 3.115,0.25 true 0.323,0.25 0.49,0.417 true 3.135,0.135 3.302,0.302 0.167,0.167 10 true *a 3.031,2.5 3.198,2.667 0.167,0.167 10 true *a 0.156,0.125 0.323,0.292 0.167,0.167 10 true *a
*a Reference Point
V100143

Butyl Tape


Apply new butyl tape to the rear door panel.


b.

Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.


c.

Install the front door service hole cover according to the reference points on the front door panel.

NOTICE:

Securely install the rear door service hole cover preventing wrinkles and air bubbles.



Hide 67628 27.INSTALL REAR DOOR TRIM BRACKET

a.
B458153

Install the rear door trim bracket with the 2 screws.


Hide 67676C 28.INSTALL NO. 2 REAR DOOR FRAME GARNISH

a.
B465116

Install the No. 2 rear door frame garnish.


Hide 29.INSTALL HOLE PLUG

a.
B458154

Install the 2 hole plugs.


Hide 68197 30.INSTALL REAR DOOR BELT SEAL

a.
B458184C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door belt seal to the rear door glass inner weatherstrip as shown in the illustration.


Hide 68174A 31.INSTALL REAR DOOR GLASS INNER WEATHERSTRIP

a.
B458185C01
0,0 0,0 false
V113147

Install in this Direction


Install the rear door glass inner weatherstrip with the rear door belt seal as shown in the illustration.


Hide 68199 32.INSTALL REAR DOOR BELT REAR SEAL

a.
B458149

Install the rear door belt rear seal.


Hide 69206C 33.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B458148

Engage the guides and claw to install the front door inside handle sub-assembly.


Hide 67604 34.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B458186C01
2.417,0.938 2.833,0.521 true 1.917,1.771 2.333,1.354 true 2.917,0.406 3.083,0.573 0.167,0.167 10 true *1 1.708,1.667 1.875,1.833 0.167,0.167 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Install in this Direction


Engage the guides to connect the rear door inside locking cable assembly and rear door lock remote control cable assembly.


b.
B458221C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws as shown in the illustration.


c.
B458222

Engage the guide and clips to install the rear door trim board sub-assembly.


d.

Install the 2 screws.


e.
B458145

Install the 3 screws.


Hide 84810D 35.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL

a.
B458187

Connect the connector.


b.
B458188C01
0,0 0,0 false
V113147

Install in this Direction


Engage the guides, clips and claws to install the rear power window regulator switch assembly with rear door armrest base upper panel as shown in the illustration.


Hide 69284D 36.INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B458189C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws to install the rear door inside handle bezel plug as shown in the illustration.


Hide 67498 37.INSTALL REAR DOOR REAR FRAME BRACKET

a.
B458190C01
0,0 0,0 false
V113147

Install in this Direction


Engage the claws and clip to install the rear door rear frame bracket as shown in the illustration.


Hide 38.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 39. INITIALIZE POWER WINDOW CONTROL SYSTEM