Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0294918 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1429  Open or Short in Brake Pedal Load Sensing Switch  


DESCRIPTION

The brake pedal load sensing switch turns on when the brake pedal is depressed with a force exceeding a predetermined level.

The skid control ECU uses this circuit to detect if the brake pedal is depressed or not.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1429 Open or Short in Brake Pedal Load Sensing Switch An open or short in the brake pedal load sensing switch circuit continues for 0.5 seconds or more.
·

Brake pedal load sensing switch (Brake pedal support assembly)

·

Brake pedal load sensing switch circuit

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C268660E16
2.073,2.281 4.177,2.719 2.104,0.438 10 false Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly) 5.417,3.083 7.01,3.458 1.594,0.375 10 false Skid Control ECU (Brake Actuator Assembly) 5.813,1.375 6.427,1.573 0.615,0.198 10 false FSW+ 3.625,1.219 4.24,1.417 0.615,0.198 10 false FSW+ 2.375,1.219 2.99,1.417 0.615,0.198 10 false FSW- 2.177,1.271 2.333,1.469 0.156,0.198 10 false 1 4.146,1.271 4.302,1.469 0.156,0.198 10 false 2 2.063,2.104 2.521,2.302 0.458,0.198 10 false A63 5.427,2.927 5.885,3.125 0.458,0.198 10 false A42 5.521,1.271 5.833,1.469 0.313,0.198 10 false 17

CAUTION / NOTICE / HINT

HINT:

When C1249, C1425 and/or C1426 is output together with C1429, inspect and repair the trouble areas indicated by C1249, C1425 and/or C1426 first: (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1249), (Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1425), and/or Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>C1246)).


PROCEDURE

1.READ VALUE USING GTS (BRAKE PEDAL LOAD SENSING SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Select the Data List using the GTS.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC/EPB > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Brake Pedal Load Sensing SW Brake pedal load sensing switch ON or OFF ON: Brake pedal depressed beyond a specified point
OFF: Brake pedal not depressed beyond a specified point
-

d.

Check that the brake pedal load sensing switch display observed on the GTS changes according to brake pedal operation.

OK:

The GTS displays ON or OFF according to brake pedal operation.



Result:
Proceed to
OK
NG



OK

2.RECONFIRM DTC

NG

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
2.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Perform a road test.



Result:
Result Proceed to
DTC C1429 is not output. A
DTC C1429 is output. (for LHD) B
DTC C1429 is output. (for RHD) C



A

B

C

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH
a.
C239141C12
1.563,2.021 0.979,2.823 true 1.823,2.021 2.406,2.823 true 0.271,0.229 0.479,0.417 0.208,0.188 10 false *a 0.688,2.875 1.146,3.063 0.458,0.188 10 false FSW+ 2.25,2.875 2.708,3.063 0.458,0.188 10 false FSW-
*a Component without harness connected
(Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly))


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


c.

Disconnect the A63 brake pedal load sensing switch connector.

NOTICE:
·

Do not remove the brake pedal load sensing switch from the brake pedal support assembly.

·

When there is a malfunction in the brake pedal load sensing switch, replace the brake pedal support assembly.




d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2 (FSW+) - 1 (FSW-) Switch OFF (Brake pedal depressed) 950 to 1050 Ω
2 (FSW+) - 1 (FSW-) Switch ON (Brake pedal released) 203 to 223 Ω


Result:
Result Proceed to
OK A
NG (for LHD) B
NG (for RHD) C




A

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL LOAD SENSING SWITCH)

B

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

C

REPLACE BRAKE PEDAL SUPPORT ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - BRAKE PEDAL LOAD SENSING SWITCH)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-17 (FSW+) - A63-2 (FSW+) Always Below 1 Ω
A42-17 (FSW+) - Body ground Always 10 kΩ or higher
A63-2 (FSW+) - Body ground Always 10 kΩ or higher
A63-1 (FSW-) - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR