Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Lines for Short Circuit  


DESCRIPTION

There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.

Symptom Trouble Area
Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
·

Short in CAN main bus lines

·

Short in CAN branch lines

·

Central gateway ECU (network gateway ECU)

·

ECM

·

Engine stop and start ECU

(w/ Stop and Start System)

·

No. 2 CAN junction connector

(w/ Stop and Start System)



WIRING DIAGRAM

w/o Stop and Start System


C360942E01
1.302,0.979 1.719,1.167 0.417,0.188 10 false 120 Ω 5.479,0.99 5.979,1.177 0.5,0.188 10 false 120 Ω 1.979,0.625 2.396,0.813 0.417,0.188 10 false CA4H 1.969,1.146 2.385,1.333 0.417,0.188 10 false CA4L 1.052,1.646 1.469,1.833 0.417,0.188 10 false F74 1.031,1.823 2.542,2.198 1.51,0.375 10 false Central Gateway ECU (Network Gateway ECU) 2.417,0.615 2.833,0.802 0.417,0.188 10 false 18 2.427,1.156 2.844,1.344 0.417,0.188 10 false 17 4.594,0.646 5.01,0.833 0.417,0.188 10 false 13 4.583,1.156 5,1.344 0.417,0.188 10 false 26 5.25,1.646 5.667,1.833 0.417,0.188 10 false A38 5.208,1.833 5.677,2.031 0.469,0.198 10 false ECM 4.823,0.615 5.24,0.802 0.417,0.188 10 false CANH 4.823,1.156 5.24,1.344 0.417,0.188 10 false CANL


w/ Stop and Start System



C360940E02
1.323,0.729 1.76,0.917 0.438,0.188 10 false CANH 1.344,1.219 1.781,1.406 0.438,0.188 10 false CANL 0.448,1.635 0.885,1.823 0.438,0.188 10 false F77 0.448,1.802 2.177,2 1.729,0.198 10 false Engine Stop and Start ECU 1.833,0.615 2.063,0.792 0.229,0.177 10 false 13 1.823,1.146 2.052,1.323 0.229,0.177 10 false 14 2.896,0.625 3.042,0.802 0.146,0.177 10 false 6 2.854,1.156 3.042,1.333 0.188,0.177 10 false 17 4.167,0.625 4.313,0.802 0.146,0.177 10 false 1 4.156,1.167 4.375,1.344 0.219,0.177 10 false 12 5.167,0.635 5.385,0.813 0.219,0.177 10 false 18 5.177,1.146 5.396,1.323 0.219,0.177 10 false 17 5.417,0.604 5.854,0.792 0.438,0.188 10 false CA4H 5.417,1.146 5.854,1.333 0.438,0.188 10 false CA4L 6.063,0.979 6.5,1.167 0.438,0.188 10 false 120 Ω 5.292,1.646 5.729,1.833 0.438,0.188 10 false F74 5.271,1.802 6.771,2.167 1.5,0.365 10 false Central Gateway ECU (Network Gateway ECU) 0.698,3.115 1.135,3.302 0.438,0.188 10 false 120 Ω 1.292,2.76 1.729,2.948 0.438,0.188 10 false CANH 1.302,3.271 1.74,3.458 0.438,0.188 10 false CANL 1.823,2.75 2.052,2.927 0.229,0.177 10 false 13 1.833,3.292 2.063,3.469 0.229,0.177 10 false 26 2.875,2.76 3.021,2.938 0.146,0.177 10 false 4 2.813,3.302 3,3.479 0.188,0.177 10 false 15 1.01,3.771 1.354,3.958 0.344,0.188 10 false A38 0.969,3.938 1.313,4.125 0.344,0.188 10 false ECM 2.656,3.771 3.042,3.958 0.385,0.188 10 false F113 2.625,3.948 4.667,4.323 2.042,0.375 10 false No. 2 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 60 km/h (37 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the ECM, refer to Service Bulletin.*1


*1: w/ Entry and Start System



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS LINES (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU (network gateway ECU).


c.
C367277C05
1.417,0.167 1.917,0.417 0.5,0.25 1.333,1.833 1.615,1.219 true 2.167,1.833 1.813,1.219 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.531,0.219 1.927,0.417 0.396,0.198 10 false F74 2.167,1.865 2.667,2.031 0.5,0.167 10 false CA4H*b 1.01,1.844 1.625,2.021 0.615,0.177 10 false CA4L*b
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F74-18 (CA4H) - F74-17 (CA4L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

3.CHECK FOR SHORT IN CAN BUS LINES (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT IN CAN BUS LINES (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the A38 ECM connector.


b.
C367277C05
1.417,0.167 1.917,0.417 0.5,0.25 1.333,1.833 1.615,1.219 true 2.167,1.833 1.813,1.219 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 1.531,0.219 1.927,0.417 0.396,0.198 10 false F74 2.167,1.865 2.667,2.031 0.5,0.167 10 false CA4H*b 1.01,1.844 1.625,2.021 0.615,0.177 10 false CA4L*b
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F74-17 (CA4L) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result Proceed to
OK (for 8NR-FTS) A
OK (for 3ZR-FAE) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366168C20
3.333,1.083 3.833,1.333 0.5,0.25 1.969,1.635 2.927,1.865 true 2.521,1.188 3.323,1.844 true 3.615,1.844 4.583,1.25 true 2.938,2.063 2.073,2.125 true 3.333,2.063 2.156,2.604 true 3.583,2.052 4.396,2.427 true 0.167,0.167 0.479,0.365 0.313,0.198 10 false *a 1.417,1.542 2.052,1.729 0.635,0.188 10 false CANH*b 1.958,1.063 2.573,1.271 0.615,0.208 10 false CANH*c 4.667,1.156 5.583,1.354 0.917,0.198 10 false CANH*d 3.427,1.125 3.802,1.313 0.375,0.188 10 false F113 1.552,2.031 2.115,2.229 0.563,0.198 10 false CANL*b 1.625,2.521 2.198,2.698 0.573,0.177 10 false CANL*c 4.49,2.375 5.406,2.573 0.917,0.198 10 false CANL*d
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to ECM *d to Engine Stop and Start ECU


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-1 (CANH) - F113-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Central gateway ECU (network gateway ECU)
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM
F113-6 (CANH) - F113-17 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher Engine stop and start ECU



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECM) C
NG (Line to ECU or sensor) D



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)

D

7.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
5.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.
C366166C28
1.417,0.75 1.917,1 0.5,0.25 1,1.76 0.708,1.313 true 1.271,2.5 1,2.021 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.51,0.792 1.906,0.958 0.396,0.167 10 false F113 0.156,1.219 0.802,1.385 0.646,0.167 10 false CANH*b 1.313,2.438 1.958,2.604 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F113-1 (CANH) - F113-12 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

6.CHECK FOR SHORT IN CAN BUS LINES (NO. 2 CAN JUNCTION CONNECTOR - ECM)
a.

Disconnect the A38 ECM connector.


b.
C366166C08
1.417,0.75 1.917,1 0.5,0.25 1.365,1.75 0.792,1.25 true 0.75,2.49 1.375,2.031 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 1.542,0.792 1.938,0.958 0.396,0.167 10 false F113 0.208,1.135 0.854,1.302 0.646,0.167 10 false CANH*b 0.26,2.51 0.906,2.677 0.646,0.167 10 false CANL*b
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to ECM


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F113-4 (CANH) - F113-15 (CANL) Cable disconnected from negative (-) battery terminal 1 MΩ or higher



Result:
Result
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - ECM)

7.CHECK FOR SHORT IN CAN BUS LINES (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.
C367281C02
1.417,0.333 1.917,0.583 0.5,0.25 2.167,1.75 1.771,1.125 true 1.333,1.75 1.667,1.125 true 0.135,0.073 0.448,0.271 0.313,0.198 10 false *a 2.115,1.781 2.594,1.979 0.479,0.198 10 false CA4L 1.042,1.781 1.521,1.979 0.479,0.198 10 false CA4H 1.552,0.375 2.031,0.573 0.479,0.198 10 false F74
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F74-17 (CA4L) Cable disconnected from negative (-) battery terminal 54 to 69 Ω


HINT:
·

If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR