Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › 2016.10–2019.09
RM32H0E _57 Power Source / Network _059621 NETWORKING _0298704 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 2 Line for Short to +B  


DESCRIPTION

There may be a short circuit between one of the CAN bus lines and +B when no resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.

Symptom Trouble Area
No resistance exists between terminal 18 (CA4H) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3, or terminal 17 (CA4L) of the central gateway ECU (network gateway ECU) and terminal 16 (BAT) of the DLC3.
·

Short to +B in CAN main bus line

·

Short to +B in CAN branch line

·

Central gateway ECU (network gateway ECU)

·

ECM

·

Engine stop and start ECU

(w/ Stop and Start System)

·

No. 2 CAN junction connector

(w/ Stop and Start System)



WIRING DIAGRAM

w/o Stop and Start System


C360942E01
1.302,0.979 1.719,1.167 0.417,0.188 10 false 120 Ω 5.479,0.99 5.979,1.177 0.5,0.188 10 false 120 Ω 1.979,0.625 2.396,0.813 0.417,0.188 10 false CA4H 1.969,1.146 2.385,1.333 0.417,0.188 10 false CA4L 1.052,1.646 1.469,1.833 0.417,0.188 10 false F74 1.031,1.823 2.542,2.198 1.51,0.375 10 false Central Gateway ECU (Network Gateway ECU) 2.417,0.615 2.833,0.802 0.417,0.188 10 false 18 2.427,1.156 2.844,1.344 0.417,0.188 10 false 17 4.594,0.646 5.01,0.833 0.417,0.188 10 false 13 4.583,1.156 5,1.344 0.417,0.188 10 false 26 5.25,1.646 5.667,1.833 0.417,0.188 10 false A38 5.208,1.833 5.677,2.031 0.469,0.198 10 false ECM 4.823,0.615 5.24,0.802 0.417,0.188 10 false CANH 4.823,1.156 5.24,1.344 0.417,0.188 10 false CANL


w/ Stop and Start System



C360940E02
1.323,0.729 1.76,0.917 0.438,0.188 10 false CANH 1.344,1.219 1.781,1.406 0.438,0.188 10 false CANL 0.448,1.635 0.885,1.823 0.438,0.188 10 false F77 0.448,1.802 2.177,2 1.729,0.198 10 false Engine Stop and Start ECU 1.833,0.615 2.063,0.792 0.229,0.177 10 false 13 1.823,1.146 2.052,1.323 0.229,0.177 10 false 14 2.896,0.625 3.042,0.802 0.146,0.177 10 false 6 2.854,1.156 3.042,1.333 0.188,0.177 10 false 17 4.167,0.625 4.313,0.802 0.146,0.177 10 false 1 4.156,1.167 4.375,1.344 0.219,0.177 10 false 12 5.167,0.635 5.385,0.813 0.219,0.177 10 false 18 5.177,1.146 5.396,1.323 0.219,0.177 10 false 17 5.417,0.604 5.854,0.792 0.438,0.188 10 false CA4H 5.417,1.146 5.854,1.333 0.438,0.188 10 false CA4L 6.063,0.979 6.5,1.167 0.438,0.188 10 false 120 Ω 5.292,1.646 5.729,1.833 0.438,0.188 10 false F74 5.271,1.802 6.771,2.167 1.5,0.365 10 false Central Gateway ECU (Network Gateway ECU) 0.698,3.115 1.135,3.302 0.438,0.188 10 false 120 Ω 1.292,2.76 1.729,2.948 0.438,0.188 10 false CANH 1.302,3.271 1.74,3.458 0.438,0.188 10 false CANL 1.823,2.75 2.052,2.927 0.229,0.177 10 false 13 1.833,3.292 2.063,3.469 0.229,0.177 10 false 26 2.875,2.76 3.021,2.938 0.146,0.177 10 false 4 2.813,3.302 3,3.479 0.188,0.177 10 false 15 1.01,3.771 1.354,3.958 0.344,0.188 10 false A38 0.969,3.938 1.313,4.125 0.344,0.188 10 false ECM 2.656,3.771 3.042,3.958 0.385,0.188 10 false F113 2.625,3.948 4.667,4.323 2.042,0.375 10 false No. 2 CAN Junction Connector

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the blind spot monitor system on using the blind spot monitor main switch (ON/OFF switch), turn the cruise control main switch on, turn the LDA main switch on and then drive the vehicle at a speed of 60 km/h (37 mph) or more for approximately 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM

·

Before replacing the ECM, refer to Service Bulletin.*1


*1: w/ Entry and Start System



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.


Result:
Result Proceed to
w/o Stop and Start System A
w/ Stop and Start System B



A

2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

B

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT TO +B IN CAN BUS LINE (CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the central gateway ECU (network gateway ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

C366210C01
1.979,1.031 2.396,1.281 0.417,0.25 5.563,1.031 5.979,1.281 0.417,0.25 1.781,2.646 2.135,2.01 true 2.49,2.646 2.25,2.01 true 6.156,2.646 6.427,2.188 true 4.5,0.969 4.708,1.167 0.208,0.198 10 false *1 0.698,0.938 0.906,1.125 0.208,0.188 10 false *a 2.052,1.073 2.396,1.281 0.344,0.208 10 false F74 5.646,1.083 5.99,1.292 0.344,0.208 10 false F41 1.26,2.563 1.833,2.792 0.573,0.229 10 false CA4L*b 2.542,2.583 3.115,2.813 0.573,0.229 10 false CA4H*b 5.844,2.563 6.417,2.792 0.573,0.229 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
*b to ECM


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F74-18 (CA4H) - F41-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
F74-17 (CA4L) - F41-16 (BAT)



Result:
Result Result
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

3.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
3.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the A38 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

C366210C01
1.979,1.031 2.396,1.281 0.417,0.25 5.563,1.031 5.979,1.281 0.417,0.25 1.781,2.646 2.135,2.01 true 2.49,2.646 2.25,2.01 true 6.156,2.646 6.427,2.188 true 4.5,0.969 4.708,1.167 0.208,0.198 10 false *1 0.698,0.938 0.906,1.125 0.208,0.188 10 false *a 2.052,1.073 2.396,1.281 0.344,0.208 10 false F74 5.646,1.083 5.99,1.292 0.344,0.208 10 false F41 1.26,2.563 1.833,2.792 0.573,0.229 10 false CA4L*b 2.542,2.583 3.115,2.813 0.573,0.229 10 false CA4H*b 5.844,2.563 6.417,2.792 0.573,0.229 10 false BAT
*1 DLC3 - -
*a Front view of wire harness connector
(to Central Gateway ECU (Network Gateway ECU))
*b to ECM


Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F41-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F74-17 (CA4L) - F41-16 (BAT)



Result:
Result Proceed to
OK (for 8NR-FTS) A
OK (for 3ZR-FAE) B
NG C



A

B

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (ECM - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

4.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the No. 2 CAN junction connector.


c.

Measure the resistance according to the value(s) in the table below.

C366167C57
1.75,1.167 2.25,1.417 0.5,0.25 5.5,1 6,1.25 0.5,0.25 6.406,2.188 6.667,2.75 true 2.042,1.844 2.917,1.333 true 1.031,1.688 1.375,1.854 true 1.208,1.208 1.76,1.844 true 2.917,2.5 2.01,2.063 true 1.052,2.354 1.396,2.063 true 1.323,2.688 1.771,2.063 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 4.604,0.135 4.917,0.333 0.313,0.198 10 false *1 1.844,1.208 2.344,1.406 0.5,0.198 10 false F113 5.625,1.052 6.125,1.25 0.5,0.198 10 false F41 6.719,2.698 7.063,2.896 0.344,0.198 10 false BAT 0.677,1.104 1.344,1.302 0.667,0.198 10 false CANH*c 3,1.24 3.667,1.438 0.667,0.198 10 false CANH*d 2.969,2.438 3.635,2.635 0.667,0.198 10 false CANL*d 0.802,2.604 1.469,2.802 0.667,0.198 10 false CANL*c 0.542,2.271 1.208,2.469 0.667,0.198 10 false CANL*b 0.49,1.604 1.156,1.802 0.667,0.198 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)
*c to ECM *d to Engine Stop and Start ECU


Standard Resistance:
Tester Connection Condition Specified Condition Connected to
F113-1 (CANH) - F41-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Central gateway ECU (network gateway ECU)
F113-12 (CANL) - F41-16 (BAT)
F113-4 (CANH) - F41-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher ECM
F113-15 (CANL) - F41-16 (BAT)
F113-6 (CANH) - F41-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher Engine stop and start ECU
F113-17 (CANL) - F41-16 (BAT)



Result:
Result Proceed to
OK A
NG (Line to central gateway ECU (network gateway ECU)) B
NG (Line to ECU or sensor) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

C

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
5.CHECK FOR SHORT TO +B IN CAN BUS LINE (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))
a.

Disconnect the F74 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

C366167C54
1.75,1.167 2.25,1.417 0.5,0.25 5.5,1 6,1.25 0.5,0.25 1.385,1.833 0.958,1.438 true 0.969,2.479 1.406,2.073 true 6.438,2.177 6.688,2.646 true 0.167,0.135 0.479,0.333 0.313,0.198 10 false *a 4.604,0.135 4.917,0.333 0.313,0.198 10 false *1 1.844,1.208 2.344,1.406 0.5,0.198 10 false F113 5.625,1.052 6.125,1.25 0.5,0.198 10 false F41 6.75,2.615 7.135,2.802 0.385,0.188 10 false BAT 0.458,2.385 1.125,2.583 0.667,0.198 10 false CANL*b 0.385,1.344 1.052,1.542 0.667,0.198 10 false CANH*b
*1 DLC3 - -
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to Central Gateway ECU (Network Gateway ECU)


Standard Resistance:
Tester Connection Condition Specified Condition
F113-1 (CANH) - F41-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F113-12 (CANL) - F41-16 (BAT)



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

B

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

C

REPAIR OR REPLACE CAN MAIN BUS LINE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU))

6.CHECK FOR SHORT TO +B IN CAN BUS LINE (ECU OR SENSOR)
a.

Reconnect all wire harness connectors.


b.

Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the bus line shorted to +B is connected.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>TERMINALS OF ECU


c.

Measure the resistance according to the value(s) in the table below.

C351161C80
5.083,0.292 5.49,0.563 0.406,0.271 1.635,0.156 2.042,0.406 0.406,0.25 6.219,2.094 6,1.719 true 1.823,1.396 1.5,0.667 true 1.979,1.396 2.333,0.667 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 3.938,0.063 4.25,0.26 0.313,0.198 10 false *1 5.177,0.354 5.49,0.552 0.313,0.198 10 false F41 6.177,2.146 6.698,2.365 0.521,0.219 10 false BAT 1.719,0.198 2.031,0.396 0.313,0.198 10 false F74 2.417,0.552 2.885,0.76 0.469,0.208 10 false CA4L 1.104,0.563 1.573,0.771 0.469,0.208 10 false CA4H
*1 DLC3 - -
*a Component with harness connected
(Central Gateway ECU (Network Gateway ECU))
- -


Standard Resistance:
Tester Connection Condition Specified Condition
F74-18 (CA4H) - F41-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
F74-17 (CA4L) - F41-16 (BAT)


HINT:
·

If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.

·

If the resistance does not become normal when the connector is disconnected from the ECU or sensor, check for a short to +B in the wire harness and repair or replace the wire harness or connector if necessary.




Result:
Result
OK
NG



OK

REPLACE ECU OR SENSOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR