55990B
1.INSTALL LOWER DEFROSTER NOZZLE ASSEMBLY
Engage the claws to install the lower defroster nozzle assembly.
2.TEMPORARILY INSTALL AIR CONDITIONER UNIT ASSEMBLY
Temporarily install the air conditioner unit assembly to the instrument panel reinforcement assembly with the 3 bolts.
3.INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY
Be sure to support the air conditioner unit assembly when installing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.
Engage the guides to install the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.
|
Install in this Direction | - | - |
Connect the 2 connectors.
Engage the clamps.
Install the 5 bolts.
Temporarily install the nut.
Install the 2 bolts.
88539J
4.CONNECT DRAIN COOLER HOSE
| *1 | Cooler Unit Drain Hose Grommet |
Connect the drain cooler hose.
If the cooler unit drain hose grommet is disconnected from the vehicle body while connecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.
82141
5.INSTALL INSTRUMENT PANEL WIRE
Engage clamps and hook to connect the instrument panel wire.
| *a | Clamp | *b | Hook |
Install the instrument panel junction block assembly with main body ECU with the bolt and nut.
Install the 2 nuts A.
Install the 4 ground wires with the 4 bolts.
Install the bolt and screw.
Connect each connector.
55308B
6.INSTALL NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY
Install the No. 3 instrument panel to cowl brace sub-assembly with the nut and bolt.
Engage the clamp and claws.
55306A
7.INSTALL NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Install the No. 1 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
Engage the clamps to connect the wire harness.
55307C
8.INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY
Install the No. 2 instrument panel brace sub-assembly with the bolt and nut.
Temporarily install the screw.
Do not fully tighten the screw.
Install the ground wire with the bolt.
Engage the clamps to connect the wire harness.
Install the relay block assembly with the 2 nuts.
9.INSTALL AIR CONDITIONER UNIT ASSEMBLY
Tighten the 3 bolts, 2 screws and nut in the order shown in the illustration to install the air conditioner unit .
55215D
10.INSTALL NO. 3 DASH PANEL INSULATOR PAD
Engage the clips to install the No. 3 dash panel insulator pad.
|
Install in this Direction |
Install the front floor carpet assembly to its original position as shown in the illustration.
Engage the clamps.
Install the clip.
Install the 2 front floor carpet clips.
88625Q
11.INSTALL COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)
Connect the aspirator and connector to install the cooler thermistor (room temperature sensor).
82878
12.INSTALL ECU INTEGRATION BOX LH
89340A
13.INSTALL CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)
85940
14.INSTALL WINDSHIELD WIPER RELAY ASSEMBLY
15.INSTALL STEERING COLUMN ASSEMBLY
55401E
16.INSTALL INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY
17.INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
18.INSTALL FRONT SEAT ASSEMBLY RH (for Manual Seat)
Use the same procedure as for the LH side.
19.INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
20.INSTALL FRONT SEAT ASSEMBLY RH (for Power Seat)
Use the same procedure as for the LH side.
88716A
21.CONNECT COOLER REFRIGERANT LIQUID PIPE A
Remove the vinyl tape from the cooler refrigerant liquid pipe A.
Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler refrigerant liquid pipe A.
ND-OIL 8 or equivalent
Install the O-ring to the cooler refrigerant liquid pipe A.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the cooler refrigerant liquid pipe A.
88707
22.CONNECT SUCTION PIPE SUB-ASSEMBLY
Remove the vinyl tape from the suction pipe sub-assembly.
Apply sufficient compressor oil to a new O-ring and fitting surface of the suction pipe sub-assembly.
ND-OIL 8 or equivalent
Install the O-ring to the suction pipe sub-assembly.
Keep the O-ring and O-ring fitting surface free of foreign matter.
Connect the suction pipe sub-assembly.
Rotate the hook connector as shown in the illustration.
Insert the hose joint into the fitting hole securely and install the bolt.
87245
23.CONNECT INLET HEATER WATER HOSE
| *a | View A |
| *b | Marking (Pink) |
| *c | Clip Installation Angle (120°) |
Connect the inlet heater water hose with the marking (pink) facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the inlet heater water hose.
87246
24.CONNECT OUTLET HEATER WATER HOSE
| *a | View A |
| *b | Marking (White) |
| *c | Clip Installation Angle (120°) |
Connect the outlet heater water hose with the marking (white) facing up and engage the clip within the area shown in the illustration.
Do not apply excessive force to the outlet heater water hose.
55701J
25.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
55735C
26.INSTALL COWL BODY MOUNTING REINFORCEMENT RH
55736D
27.INSTALL COWL BODY MOUNTING REINFORCEMENT LH
55734D
28.INSTALL WATER GUARD PLATE LH
55737B
29.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL
30.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY
31.ADD ENGINE COOLANT
32.INSPECT FOR COOLANT LEAK
33. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
34.WARM UP ENGINE
35.INSPECT FOR REFRIGERANT LEAK