Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › CYLINDER HEAD GASKET › 2019.09–2020.08
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0292814 CYLINDER HEAD GASKET A

3ZR-FAE ENGINE MECHANICAL  CYLINDER HEAD GASKET  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the cylinder head gasket removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedure Effect/Inoperative when not Performed Link
Disconnect cable from negative battery terminal Perform steering sensor zero point calibration Toyota parking assist-sensor system*1 (Click here)
Simple intelligent parking assist system*1
Initialize back door lock Power door lock control system (Click here)
Replacement of CVT fluid ATF thermal degradation estimate reset The value of the Data List item "ATF thermal Degradation Estimate" is not estimated correctly (Click here)
Front wheel alignment adjustment Perform the following procedures in the order shown:
1.

Clear zero point calibration data and store system information

2.

Perform yaw rate and acceleration sensor zero point calibration and store system information


·

VSC disabled or malfunctions

·

DTCs are stored

·

Slip indicator light illuminates

·

ABS warning light illuminates


(Click here)

*1: When performing learning using the GTS.

Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>TOYOTA PARKING ASSIST-SENSOR SYSTEM>CALIBRATION

PROCEDURE

Hide 11103 1.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 16268 2.REMOVE NO. 1 WATER BY-PASS PIPE

a.
A177452

Remove the 2 bolts and No. 1 water by-pass pipe.


Hide 11101 4.REMOVE CYLINDER HEAD SUB-ASSEMBLY

a.
A150891N20
0.583,0.102 0.691,0.253 0.108,0.152 10 3 1.122,0.102 1.229,0.253 0.108,0.152 10 7 1.668,0.115 1.775,0.267 0.108,0.152 10 9 2.2,0.115 2.308,0.267 0.108,0.152 10 6 2.768,0.095 2.875,0.247 0.108,0.152 10 2 0.556,1.784 0.664,1.936 0.108,0.152 10 1 1.095,1.784 1.202,1.936 0.108,0.152 10 5 1.606,1.784 1.797,1.936 0.191,0.152 10 10 2.225,1.784 2.333,1.936 0.108,0.152 10 8 2.775,1.784 2.883,1.936 0.108,0.152 10 4

Using a 10 mm bi-hexagon wrench, uniformly loosen and remove the 10 cylinder head set bolts and 10 plate washers in several steps in the order shown in the illustration.

NOTICE:
·

Removing the cylinder head set bolts in the wrong order may cause warpage or cracking of the cylinder head sub-assembly.

·

Do not drop the plate washers into the cylinder head sub-assembly.




b.

Using a screwdriver, remove the cylinder head sub-assembly by prying between the cylinder head sub-assembly and cylinder block sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder head sub-assembly and cylinder block sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 11115 5.REMOVE CYLINDER HEAD GASKET

a.
A224212

Remove the cylinder head gasket from the cylinder block sub-assembly.


Hide 11101A 7.INSPECT CYLINDER HEAD SET BOLT