Home › Engine / Hybrid System › 3ZR-FAE (ENGINE MECHANICAL) › ENGINE UNIT › from 2019.09
RM32H0E _51 Engine / Hybrid System _059726 3ZR-FAE ENGINE MECHANICAL _0294289 ENGINE UNIT A

3ZR-FAE ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 12108 1.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.
A173599

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


Hide 12108A 2.REMOVE OIL FILLER CAP GASKET

a.
A128159

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 3.REMOVE ENGINE COVER JOINT

a.
A150847

Remove the 2 engine cover joints.


Hide 11101J 6.REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

Hide 11401G 7.REMOVE CRANKSHAFT POSITION SENSOR

Hide 83530 8.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 89422 10.REMOVE ENGINE COOLANT TEMPERATURE SENSOR

Hide 11201 11.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

a.
A173472

Remove the 13 bolts, seal washer and cylinder head cover sub-assembly.


b.
A165301

Remove the 3 gaskets from the camshaft bearing cap.

NOTICE:

As gaskets may stick to the cylinder head cover sub-assembly, be careful not to drop any of the gaskets into the engine when removing the cylinder head cover sub-assembly.



Hide 11213 12.REMOVE CYLINDER HEAD COVER GASKET

a.
A179166

Remove the cylinder head cover gasket.


Hide 11193 13.REMOVE SPARK PLUG TUBE GASKET

a.
A179167

Pry up the 4 claws of the ventilation baffle plate.

NOTICE:

Do not deform the claws of the ventilation baffle plate more than necessary.



b.

Remove the 4 spark plug tube gaskets from the cylinder head cover sub-assembly.

NOTICE:

Be careful not to damage the cylinder head cover sub-assembly.


HINT:

Prevent the spark plug tube gaskets from being deformed as much as possible. The removed spark plug tube gaskets will be used when installing new spark plug tube gaskets.



Hide 15600A 15.REMOVE OIL FILTER UNION

A365984

a.

Using a 12 mm hexagon socket wrench, remove the oil filter union from the oil filter bracket.


Hide 16.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.
A294384C04
2.177,1.74 1.458,2.281 1.458,2.281 1.01,1.667 true 0.531,2.448 0.719,2.448 0.719,2.448 1.063,3.125 true 0.469,3.885 0.615,3.885 0.615,3.885 0.979,3.271 true 1.375,2.333 1.688,2.49 0.313,0.156 10 *a 0.292,3.823 0.604,3.979 0.313,0.156 10 *b 0.344,2.385 0.656,2.542 0.313,0.156 10 *a
*a Timing Mark
*b Timing Notch


Turn the crankshaft pulley until its timing notch and timing mark "0" of the timing chain cover sub-assembly are aligned.


b.

Check that timing marks on both the camshaft timing exhaust gear assembly and camshaft timing gear assembly are facing upward as shown in the illustration.

HINT:

If not, turn the crankshaft 1 complete revolution (360°) and align the marks as above.



Hide 13540 18.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

a.
A250765

Remove the 2 nuts, bracket, No. 1 chain tensioner assembly and gasket.

NOTICE:

Do not turn the crankshaft without the No. 1 chain tensioner assembly installed.



Hide 11302 19.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11302A 20.REMOVE TIMING CHAIN COVER OIL SEAL

Hide 16323 21.REMOVE WATER INLET HOUSING

a.
A150906

Remove the 3 bolts, water inlet housing and gasket.


Hide 12511 22.REMOVE NO. 1 GENERATOR BRACKET

a.
A394380

Remove the 4 bolts and No. 1 generator bracket.


Hide 13559 23.REMOVE CHAIN TENSIONER SLIPPER

a.
A173477

Remove the chain tensioner slipper from the cylinder block sub-assembly.


Hide 13561 24.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A165303

Remove the 2 bolts and No. 1 chain vibration damper.


Hide 13506 25.REMOVE CHAIN SUB-ASSEMBLY

a.
A165304

Hold the hexagonal portion of the camshaft with a wrench and turn the camshaft timing gear assembly counterclockwise to loosen the chain sub-assembly between the camshaft timing exhaust gear assembly and camshaft timing gear assembly.


b.

With the chain sub-assembly loosened, release the chain sub-assembly from the camshaft timing gear assembly and place it on the camshaft timing gear assembly.

HINT:

Be sure to release the chain sub-assembly from the sprocket completely.



c.

Turn the camshaft clockwise to return it to the original position and remove the chain sub-assembly.


Hide 13521 26.REMOVE CRANKSHAFT TIMING SPROCKET

Hide 13507 27.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Hide 19315 28.REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE

a.
A150874

Remove the No. 1 crankshaft position sensor plate.


Hide 13521A 29.REMOVE CRANKSHAFT TIMING GEAR KEY

a.
A150909C23
0.854,0.76 0.969,0.76 0.969,0.76 1.188,1.354 true 0.677,0.667 0.844,0.833 0.167,0.167 10 false *a
*a Protective Tape


Using a screwdriver, remove the 2 crankshaft timing gear keys.

HINT:

Tape the screwdriver tip before use.



Hide 13050 30.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 31.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13050 32.REMOVE CAMSHAFT TIMING GEAR ASSEMBLY

Hide 13070A 33.REMOVE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

Hide 13908 34.REMOVE VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY

Hide 13908 35.INSTALL VALVE ROCKER ARM LOST MOTION DAMPER SUB-ASSEMBLY

Hide 11103 36.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY

Hide 222A0 37.REMOVE CONTINUOUSLY VARIABLE VALVE LIFT CONTROLLER ASSEMBLY

Hide 13801 38.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.
A289034

Remove the 16 No. 1 valve rocker arm sub-assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13750 39.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.
A289033

Remove the 16 valve lash adjuster assemblies.

HINT:

Arrange the removed parts in the correct order.



Hide 13716 40.REMOVE VALVE STEM CAP

a.
A150945

Remove the 16 valve stem caps.

HINT:

Arrange the removed parts in the correct order.



Hide 11101 41.REMOVE CYLINDER HEAD SUB-ASSEMBLY

Hide 11114A 42.REMOVE CAMSHAFT HOUSING STRAIGHT PIN

NOTICE:

It is not necessary to remove a camshaft housing straight pin unless it is being replaced.


Hide 12204 44.REMOVE PCV VALVE (VENTILATION VALVE SUB-ASSEMBLY)

Hide 12101A 45.REMOVE OIL PAN DRAIN PLUG

a.
A150893

Remove the oil pan drain plug and gasket.


Hide 12102A 46.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15100 47.REMOVE OIL PUMP ASSEMBLY

Hide 11420 49.REMOVE STIFFENING CRANKCASE ASSEMBLY

a.
A150897

Uniformly loosen and remove the 11 bolts.


b.
A150898C10
0.396,3.115 0.396,4.083 0.396,4.083 1.125,3.573 false 3.01,2.625 3.01,3.938 3.01,3.938 2.573,3.458 false 2.948,3.99 3.219,4.167 0.271,0.177 10 *a 0.313,4.115 0.594,4.313 0.281,0.198 10 *a
*a Protective Tape


Using a screwdriver, remove the stiffening crankcase assembly by prying between the stiffening crankcase assembly and cylinder block sub-assembly.

NOTICE:

Be careful not to damage the contact surfaces of the stiffening crankcase assembly and cylinder block sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 11432A 50.REMOVE NO. 1 TAPER SCREW PLUG

a.
A235913

Remove the 2 No. 1 taper screw plugs.


Hide 51.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 52.REMOVE STIFFENING CRANKCASE RING PIN

NOTICE:

It is not necessary to remove a stiffening crankcase ring pin unless it is being replaced.