Home › Suspension › FRONT SUSPENSION › FRONT SUSPENSION MEMBER › from 2019.09
RM32H0E _53 Suspension _059519 FRONT SUSPENSION _0291587 FRONT SUSPENSION MEMBER A

FRONT SUSPENSION  FRONT SUSPENSION MEMBER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL HOLE PLUG

a.

Install the 4 hole plugs to the front suspension crossmember sub-assembly.

HINT:

There are 2 different shapes of hole plug.



Hide 51228G 2.INSTALL FRONT SUSPENSION MEMBER PLATE

a.

Install the 2 front suspension member plates to the front suspension crossmember sub-assembly.


Hide 12363A 3.INSTALL ENGINE MOVING CONTROL ROD

a.

Install the engine moving control rod to the front suspension crossmember sub-assembly with the bolt.

Torque:
200 N*m (2039 kgf*cm, 148 ft.*lbf)


Hide 48069 4.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Temporarily install the front lower No. 1 suspension arm sub-assembly LH to the front suspension crossmember sub-assembly with the 2 bolts and nut.


Hide 48068 5.TEMPORARILY INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 48811 6.INSTALL FRONT STABILIZER BAR

Hide 48829A 7.INSTALL FRONT NO. 1 STABILIZER BRACKET LH

Hide 48824A 8.INSTALL FRONT NO. 1 STABILIZER BRACKET RH

HINT:

Perform the same procedure as for the LH side.


Hide 9.INSTALL STEERING LINK ASSEMBLY

a.

Install the steering link assembly to the front suspension crossmember sub-assembly with the 2 bolts and 2 new nuts.

Torque:
133 N*m (1356 kgf*cm, 98 ft.*lbf)

NOTICE:
·

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut secured.

·

Make sure to tighten the bolts starting from the left side of the vehicle.




Hide 51201 10.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Slowly jack up the front suspension crossmember sub-assembly with an engine lifter using 4 attachments or equivalent tools.

CAUTION:
C345334

·

The front suspension crossmember sub-assembly is a very heavy component. Make sure that it is supported securely.

·

If the front suspension crossmember sub-assembly is not securely supported, it may drop, resulting in serious injury.



NOTICE:

Use attachments to keep the front suspension crossmember sub-assembly level.



b.

Install the front suspension crossmember sub-assembly to the vehicle body with the 6 bolts.

Torque:
141 N*m (1438 kgf*cm, 104 ft.*lbf)


c.

Lower the engine lifter.


d.

Install the engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


e.

for AWD:

i.

Install the wire harness clamp bracket to the front suspension crossmember sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



f.

for 2WD:

i.

Install the 2 wire harness clamp brackets to the front suspension crossmember sub-assembly with the 2 bolts.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)



Hide 48069 11.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

a.

Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly LH with the bolt and 2 nuts.

Torque:
89 N*m (908 kgf*cm, 66 ft.*lbf)


Hide 48068 12.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45047 13.CONNECT TIE ROD END SUB-ASSEMBLY LH

Hide 45046 14.CONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 43215 15.INSTALL STEERING KNUCKLE SEAL (w/ Seal)

Hide 48810 16.CONNECT FRONT STABILIZER LINK ASSEMBLY LH

a.

Connect the front stabilizer link assembly LH to the front shock absorber assembly with the nut.

Torque:
74 N*m (755 kgf*cm, 55 ft.*lbf)

NOTICE:

Do not damage the boot of the ball joint.


HINT:

If the ball joint turns together with the nut, use a 6 mm hexagon socket wrench to hold the stud bolt.



b.

Install the cap.


Hide 48820B 17.CONNECT FRONT STABILIZER LINK ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 51108A 18.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

a.

Install the rear side rail reinforcement sub-assembly LH to the front suspension crossmember sub-assembly and vehicle body with the 4 bolts.

Torque:
70 N*m (714 kgf*cm, 52 ft.*lbf)


Hide 51107A 19.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 45025D 20.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 21.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 22.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 23.INSTALL FRONT WHEELS

Hide 48069 25.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

Hide 48068 26.FULLY TIGHTEN FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH

HINT:

Perform the same procedure as for the LH side.


Hide 58166 27.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 58165B 28.INSTALL FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 51444A 29.INSTALL REAR ENGINE UNDER COVER LH

Hide 51443C 30.INSTALL REAR ENGINE UNDER COVER RH

Hide 51441 31.INSTALL NO. 1 ENGINE UNDER COVER

Hide 32.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT

Hide 34.PERFORM CALIBRATION

·

Parking support brake system

·

Simple intelligent parking assist system


(Click here)
Panoramic view monitor system (Click here)