Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE CARRIER (for AWD) › from 2019.09
RM32H0E _52 Drivetrain _059517 AXLE AND DIFFERENTIAL _0291571 REAR AXLE CARRIER(for AWD) A

AXLE AND DIFFERENTIAL  REAR AXLE CARRIER(for AWD)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during rear axle carrier sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Rear wheel alignment adjustment
1.

Clear zero point calibration data.

2.

Perform yaw rate and acceleration sensor zero point calibration.


·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Removal/installation of rear height control sensor sub-assembly LH*1 Initialize headlight ECU sub-assembly LH Automatic headlight beam level control system (Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement)*1

*1: w/ Height Control Sensor


HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1.REMOVE REAR WHEEL

Hide 42312B 2.REMOVE REAR AXLE SHAFT NUT

Hide 3.SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

Hide 42431 4.REMOVE REAR DISC

Hide 42450B 6.REMOVE REAR AXLE HUB AND BEARING ASSEMBLY

Hide 7.REMOVE FLEXIBLE HOSE BRACKET

a.
C365607

Remove the bolt and flexible hose bracket from the rear axle carrier sub-assembly.


Hide 89408C 8.REMOVE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Height Control Sensor)

Hide 48840A 9.REMOVE REAR STABILIZER LINK ASSEMBLY

Hide 48231B 10.REMOVE REAR COIL SPRING

Hide 48258C 11.REMOVE REAR LOWER COIL SPRING INSULATOR

Hide 48720A 12.REMOVE REAR NO. 1 SUSPENSION ARM ASSEMBLY

Hide 13.REMOVE REAR AXLE CARRIER SUB-ASSEMBLY

a.
C348734

Loosen the 2 bolts of the rear trailing arm assembly.


b.
C348735C02
0.729,0.594 0.917,0.583 0.917,0.583 1.104,0.833 false 0.448,0.521 0.719,0.729 0.271,0.208 10 true *1
*1 Rear Axle Carrier Pin


Loosen the nut of the rear shock absorber assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



c.
C345054C01
1.531,2.438 1.969,2.438 false 1.531,3.073 1.969,3.073 false 1.354,2.354 1.667,2.51 0.313,0.156 10 false *a 1.333,2.99 1.646,3.146 0.313,0.156 10 false *b
*a Wooden Block
*b Jack


Using a jack and a wooden block, support the rear axle carrier sub-assembly.

NOTICE:
·

When jacking up the rear axle carrier sub-assembly, be sure to jack it up slowly.

·

Make sure to perform this operation with the vehicle kept as low as possible.




d.
C345055N02
0.958,0.292 1.115,0.49 0.156,0.198 10 true A

Loosen the bolt (A).

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.



e.

Remove the 2 bolts and separate the rear trailing arm assembly from the rear axle carrier sub-assembly.


f.

Remove the nut and separate the rear shock absorber assembly from the rear axle carrier sub-assembly.

NOTICE:

Hold the rear axle carrier pin while rotating the nut.



g.

Remove the bolt (A), nut and rear axle carrier sub-assembly from the rear upper control arm assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Loosen the bolt with the nut secured.