Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING UNIT (for VALEO Made) › from 2020.08
RM32H0E _58 Vehicle Interior _059841 HEATING / AIR CONDITIONING _0293719 AIR CONDITIONING UNIT(for VALEO Made) A

HEATING / AIR CONDITIONING  AIR CONDITIONING UNIT(for VALEO Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the air conditioner unit assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) battery terminal Memorize steering angle neutral point Panoramic view monitor system (Click here)
AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)
·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Front Passenger Side Upper Air Mix)

·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Driver Side Upper Air Mix)

·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Driver Side Lower Air Mix)

·

No. 2 Air Conditioning Radiator Damper Servo Sub-assembly (Mode Switching)

·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Front Passenger Side Lower Air Mix)

·

Air conditioning amplifier assembly


AIR CONDITIONING SYSTEM (for Manual Air Conditioning System)
·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Upper Air Mix)

·

No. 1 Air Conditioning Radiator Damper Servo Sub-assembly (Lower Air Mix)

·

No. 2 Air Conditioning Radiator Damper Servo Sub-assembly (Mode Switching)

·

Air conditioning amplifier assembly


Initialize servo motor (Air conditioning system) DTCs are stored for Automatic Air Conditioning System:(Click here)
for Manual Air Conditioning System:(Click here)

HINT:
·

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: When performing learning using the GTS

Click here(Click here)

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Simple intelligent parking assist system*1
Parking support brake system*1


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFC-134a(R134a))

Hide 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM (for HFO-1234yf(R1234yf))

Hide 3. DRAIN ENGINE COOLANT (for 8NR-FTS)

Hide 4. DRAIN ENGINE COOLANT (for 3ZR-FAE)

Hide 5.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55737B 6.REMOVE NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 55736D 7.REMOVE COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735C 8.REMOVE COWL BODY MOUNTING REINFORCEMENT RH

Hide 55701J 9.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 10.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 87246 11.DISCONNECT OUTLET HEATER WATER HOSE

a.
I112329

Slide the hose clip to disconnect the outlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the outlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the outlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 87245 12.DISCONNECT INLET HEATER WATER HOSE

a.
I112330

Slide the hose clip to disconnect the inlet heater water hose.

NOTICE:
·

To prevent contamination by foreign matter or water droplets, protect the connecting portions of the inlet heater water hose and air conditioner radiator assembly with plastic bags.

·

Do not apply excessive force to the inlet heater water hose.

·

Prepare a drain pan or cloth in case the coolant leaks.




Hide 88707 13.DISCONNECT SUCTION PIPE SUB-ASSEMBLY

a.
I112331

Remove the bolt.


b.
I112332

Disconnect the suction pipe sub-assembly and cooler refrigerant liquid pipe A shown in the illustration.


c.

Remove the 2 O-rings from the suction pipe sub-assembly and cooler refrigerant liquid pipe A.

NOTICE:

Seal the openings of the disconnected parts using vinyl tape to prevent entry of moisture and foreign matter.



Hide 14.REMOVE FRONT SEAT ASSEMBLY LH (for Manual Seat)

Hide 15.REMOVE FRONT SEAT ASSEMBLY RH (for Manual Seat)

HINT:

Use the same procedure as for the LH side.


Hide 16.REMOVE FRONT SEAT ASSEMBLY LH (for Power Seat)

Hide 17.REMOVE FRONT SEAT ASSEMBLY RH (for Power Seat)

HINT:

Use the same procedure as for the LH side.


Hide 55401E 18.REMOVE INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY

Hide 19.REMOVE STEERING COLUMN ASSEMBLY

Hide 85940 20.REMOVE WINDSHIELD WIPER RELAY ASSEMBLY

Hide 89340A 21.REMOVE CLEARANCE WARNING ECU ASSEMBLY (w/ Clearance Sonar System)

Hide 82877 22.REMOVE ECU INTEGRATION BOX RH (for LHD)

Hide 82878 23.REMOVE ECU INTEGRATION BOX LH (for RHD)

Hide 88625Q 24.REMOVE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

a.
I112333

Disconnect the connector and air conditioning duct sub-assembly to remove the cooler thermistor (room temperature sensor).


Hide 55215D 25.REMOVE NO. 3 DASH PANEL INSULATOR PAD

a.
I112338

Remove the 2 front floor carpet clips.


b.
I112339C02
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.


d.
I112343

Disengage the clips to remove the No. 3 dash panel insulator pad.


Hide 87212K 26.REMOVE REAR NO. 6 AIR DUCT (w/ Rear Air Duct)

a.
I112340C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 6 air duct as shown in the illustration.


Hide 87212J 27.REMOVE REAR NO. 5 AIR DUCT (w/ Rear Air Duct)

a.
I112341C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 5 air duct as shown in the illustration.


Hide 87212H 28.REMOVE REAR NO. 4 AIR DUCT (w/ Rear Air Duct)

a.
I112334

Remove the 2 front floor carpet clips.


b.
I112335C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the clip.


c.

Disengage the clamps to turn back the front floor carpet assembly as shown in the illustration.


d.
I112336C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 4 air duct as shown in the illustration.


Hide 87212G 29.REMOVE REAR NO. 3 AIR DUCT (w/ Rear Air Duct)

a.
I112337C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 3 air duct as shown in the illustration.


Hide 87212F 30.REMOVE REAR NO. 2 AIR DUCT (w/ Rear Air Duct)

a.
I112342C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 2 air duct.


Hide 87212 31.REMOVE REAR NO. 1 AIR DUCT (w/ Rear Air Duct)

a.
I112501C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear No. 1 air duct as shown in the illustration.


Hide 55306A 32.REMOVE NO. 1 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

w/ PTC Heater:

i.
E339409

Remove the bolt to disconnect the ground wire.



b.
I112345

Remove the 2 nuts and separate the relay block assembly.


c.

for LHD:

i.
I113757

Disengage the clamps to disconnect the wire harness.


ii.
I113758

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.



d.

for RHD:

i.
I113738

Disengage the clamps to disconnect the wire harness.


ii.
I113739

Remove the bolt, screw, nut and No. 1 instrument panel brace sub-assembly.



Hide 55307C 33.REMOVE NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY

a.

for LHD:

i.
I112542

Remove the bolt to disconnect the ground wire.


ii.

Disengage the clamps to disconnect the wire harness.


iii.

Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.



b.

for RHD:

i.
I113736

Remove the bolt to disconnect the ground wire.


ii.

Disengage the clamps to disconnect the wire harness.


iii.
I113737

Remove the bolt, screw, nut and No. 2 instrument panel brace sub-assembly.



Hide 55308B 34.REMOVE NO. 3 INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY

a.
I112348

Disengage the clamp and claws.


b.

Remove the bolt, nut and No. 3 instrument panel to cowl brace sub-assembly.


Hide 88539J 35.REMOVE DRAIN COOLER HOSE

a.
I112352C01
1.656,3.083 1.24,2.896 true 1.688,3 1.948,3.208 0.26,0.208 10 true *1
*1 Cooler Unit Drain Hose Grommet


Disconnect the drain cooler hose.

NOTICE:

If the cooler unit drain hose grommet is disconnected from the vehicle body while disconnecting the drain cooler hose, make sure to replace it with a new one. Failure to do so may cause water ingress.



Hide 82141 36.DISCONNECT INSTRUMENT PANEL WIRE

a.

for LHD:

i.

Disconnect each connector.

I113769C01
0.469,1.073 0.729,0.885 true 1.646,1.365 1.865,1.219 true 3.552,1.01 3.083,1.094 3.083,1.094 2.979,0.813 true 4.521,0.375 3.958,0.188 3.958,0.188 4.177,0.385 true 6.219,0.604 5.354,0.813 5.354,0.813 5.552,1.031 true 6.167,1.313 6.448,1.354 true 6.25,2.542 6.844,2.906 6.844,2.906 6.448,3.146 true 3.875,4.281 3.708,4.979 3.708,4.979 3.198,4.281 true 2.5,4.333 2.635,3.76 2.635,3.76 2.25,4.073 true 2.531,4.656 2.583,4.854 true 0.833,4.938 1.063,5.094 true 0.542,5.271 0.771,5.427 true 0.729,0.75 0.948,0.948 0.219,0.198 10 true *a 0.344,5.146 0.552,5.333 0.208,0.188 10 true *b 1.448,1.271 1.667,1.469 0.219,0.198 10 true *a 2.99,1.125 3.208,1.323 0.219,0.198 10 true *a 3.74,0.073 3.958,0.271 0.219,0.198 10 true *a 5.104,0.698 5.323,0.896 0.219,0.198 10 true *a 5.948,1.177 6.167,1.375 0.219,0.198 10 true *a 6.875,2.802 7.094,3 0.219,0.198 10 true *a 3.635,5 3.854,5.198 0.219,0.198 10 true *a 2.677,3.635 2.896,3.833 0.219,0.198 10 true *a 2.51,4.865 2.729,5.063 0.219,0.198 10 true *a 0.969,5.094 1.188,5.292 0.219,0.198 10 true *a
*a Clamp *b Hook



ii.

Remove the bolt and screw.


iii.

Remove the 4 bolts to disconnect the 4 ground wires.


iv.

Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.


v.

Disengage clamps and hook to disconnect the instrument panel wire.



b.

for RHD:

i.

Disconnect each connector.

I113770C01
0.635,1 0.896,1.125 true 1.615,0.323 1.344,0.521 true 2.667,1.135 2.771,1.281 true 3.323,0.979 3.75,1.208 3.75,1.208 4.177,0.927 true 6.469,0.792 6.656,1.042 true 6.583,4.906 6.75,4.521 6.75,4.521 6.552,4.125 true 6.229,5.479 6.438,5.583 true 3.26,4.375 3.615,4.854 3.615,4.854 3.833,4.302 true 2.469,4.74 2.677,4.615 true 0.5,5.271 0.719,5.438 true 0.844,4.958 1.063,5.125 true 0.917,1.052 1.115,1.24 0.198,0.188 10 true *a 0.26,5.146 0.469,5.344 0.208,0.198 10 true *b 1.156,0.427 1.354,0.615 0.198,0.188 10 true *a 2.688,1.281 2.885,1.469 0.198,0.188 10 true *a 3.646,1.219 3.844,1.406 0.198,0.188 10 true *a 6.281,0.688 6.479,0.875 0.198,0.188 10 true *a 5.521,4.042 5.719,4.229 0.198,0.188 10 true A 5.604,4.354 5.802,4.542 0.198,0.188 10 true A 6.802,4.417 7,4.604 0.198,0.188 10 true *a 6.01,5.375 6.208,5.563 0.198,0.188 10 true *a 3.51,4.854 3.708,5.042 0.198,0.188 10 true *a 2.688,4.51 2.885,4.698 0.198,0.188 10 true *a 0.979,5.135 1.177,5.323 0.198,0.188 10 true *a 6.833,5.083 7.031,5.271 0.198,0.188 10 false B 5.625,0.292 5.823,0.479 0.198,0.188 10 true C 5.698,0.615 5.896,0.802 0.198,0.188 10 true C 1.927,0.344 2.125,0.531 0.198,0.188 10 true C
*a Clamp *b Hook



ii.

Remove the bolt and screw.


iii.

Remove the 4 bolts to disconnect the 4 ground wires.


iv.

Remove the 2 nuts A.


v.

Remove the bolt and nut to separate the instrument panel junction block assembly with main body ECU.


vi.

Disengage clamps and hook to disconnect the instrument panel wire.



Hide 37.REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONER UNIT ASSEMBLY

NOTICE:
·

Be sure to support the air conditioner unit assembly when removing it. Failure to do so may cause the bracket of the air conditioner unit assembly to break.

·

When disassembling the air conditioner unit assembly, eliminate static electricity by touching the vehicle body to prevent the components from being damaged.



a.
I112353

Remove the 2 bolts.


b.

Remove the 5 bolts.

I113768


c.

Remove the nut.


d.
I112356

Disengage the clamps.


e.

Disconnect 2 connectors.


f.

Disengage the guides to remove the instrument panel reinforcement assembly with air conditioner unit assembly as shown in the illustration.

I112355C01
0,0 0,0 false
V113147

Remove in this Direction - -



Hide 38.REMOVE AIR CONDITIONER UNIT ASSEMBLY

a.

Remove the 3 bolts and air conditioner unit assembly from the instrument panel reinforcement assembly.

I112357


Hide 55990B 39.REMOVE LOWER DEFROSTER NOZZLE ASSEMBLY

a.
I112349

Disengage the claws to remove the lower defroster nozzle assembly.