Home › Engine / Hybrid System › 8NR-FTS (EMISSION CONTROL) › MONOLITHIC CONVERTER › from 2020.08
RM32H0E _51 Engine / Hybrid System _060038 8NR-FTS EMISSION CONTROL _0294114 MONOLITHIC CONVERTER A

8NR-FTS EMISSION CONTROL  MONOLITHIC CONVERTER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL STUD BOLT (for AWD)

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

w/ Differential Pressure Sensor:

i.

Using an E10 "TORX" socket wrench, install the 2 stud bolts.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)


ii.

Using an E7 "TORX" socket wrench, install the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



b.

w/o Differential Pressure Sensor:

i.

Using an E10 "TORX" socket wrench, install the 2 stud bolts.

Torque:
19.5 N*m (199 kgf*cm, 14 ft.*lbf)



Hide 25733A 2.INSTALL NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)

a.

for 2WD:

i.

Using a 14 mm union nut wrench, connect the No. 1 vacuum pipe to the exhaust manifold converter sub-assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench. When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)



ii.

Install the No. 1 vacuum pipe with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


iii.

Install the vacuum transmitting hose to the differential pressure sensor and No. 1 vacuum pipe, and slide the 2 clips to secure the hoses.



b.

for AWD:

i.

Using a 14 mm union nut wrench, connect the No. 1 vacuum pipe to the exhaust manifold converter sub-assembly.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)

HINT:

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench. When using a union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26.3 N*m (268 kgf*cm, 19 ft.*lbf)



ii.

Install the No. 1 vacuum pipe with the nut.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


iii.

Install the vacuum transmitting hose to the differential pressure sensor and No. 1 vacuum pipe, and slide the 2 clips to secure the hoses.



Hide 17279 3.INSTALL OUTLET TURBINE ELBOW GASKET

a.

Install a new outlet turbine elbow gasket to the turbocharger sub-assembly.


Hide 25051 4.INSTALL EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)

a.

Temporarily install the exhaust manifold converter sub-assembly (TWC: Front Catalyst) to the turbocharger sub-assembly with 4 new nuts.


b.
A393784C02
0.083,0.083 0.333,0.302 0.25,0.219 12 true *A 0.083,2.5 0.344,2.729 0.26,0.229 12 true *B 1.927,0.458 2.083,0.656 0.156,0.198 10 true 1 1.802,2.76 1.958,2.958 0.156,0.198 10 true 1 0.344,3.323 0.5,3.521 0.156,0.198 10 true 2 0.76,3.948 0.927,4.146 0.167,0.198 10 true 3 1.448,2.51 1.604,2.708 0.156,0.198 10 true 4 1.646,0.146 1.802,0.344 0.156,0.198 10 true 4 0.688,0.958 0.844,1.156 0.156,0.198 10 true 2 1.021,1.469 1.188,1.667 0.167,0.198 10 true 3
*A for 2WD
*B for AWD


Tighten the 4 nuts in the order shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 25586 5.INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR (for 2WD)

a.

Temporarily install the No. 1 manifold converter insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 3 bolts.


b.
A351369N01
1.208,1.615 1.365,1.813 0.156,0.198 10 true 2 1.865,0.458 2.021,0.656 0.156,0.198 10 true 1 1.604,1.167 1.76,1.365 0.156,0.198 10 true 3

Tighten the 3 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17272 6.INSTALL NO. 2 TURBO INSULATOR

a.

Temporarily install the No. 2 turbo insulator to the cylinder head sub-assembly and heat insulator bracket with the 2 bolts.


b.
A351368N02
1.958,0.052 2.115,0.25 0.156,0.198 10 true 2 2.5,1.958 2.656,2.156 0.156,0.198 10 true 1

Tighten the 2 bolts in the order shown in the illustration.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25587 7.INSTALL NO. 2 MANIFOLD CONVERTER INSULATOR (for AWD)

a.
A393780N01
1.271,0.563 1.427,0.76 0.156,0.198 10 true 1 2.24,0.396 2.396,0.594 0.156,0.198 10 true 2 2.125,1.802 2.281,2 0.156,0.198 10 true 3

Temporarily install the No. 2 manifold converter insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 3 bolts.


b.

Tighten the 3 nuts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 25586 8.INSTALL NO. 1 MANIFOLD CONVERTER INSULATOR (for AWD)

a.
A427494N01
0.813,1.156 0.99,1.344 0.177,0.188 10 true 1 1.865,1.188 2.042,1.375 0.177,0.188 10 true 2 0.854,1.75 1.031,1.938 0.177,0.188 10 true 3 0.563,0.135 0.74,0.323 0.177,0.188 10 true 4

w/ Differential Pressure Sensor:

i.

Temporarily install the No. 1 manifold converter insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with nut, 3 bolts.


ii.

Tighten the nut, 3 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)



b.
A393781N01
1.813,0.49 1.969,0.688 0.156,0.198 10 true 1 2,0.74 2.156,0.938 0.156,0.198 10 true 2 0.813,0.25 0.969,0.448 0.156,0.198 10 true 3 1,1.688 1.156,1.885 0.156,0.198 10 true 4

w/o Differential Pressure Sensor:

i.

Temporarily install the No. 1 manifold converter insulator to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with 4 bolts.


ii.

Tighten the 4 bolts in the order shown in the illustration.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)



Hide 37109A 9.INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY (for AWD)

a.
A393783N01
2.146,0.104 2.302,0.302 0.156,0.198 10 true 1 2.052,1.969 2.208,2.167 0.156,0.198 10 true 2

Temporarily install the propeller shaft heat insulator bracket sub-assembly to the transfer assembly with the 2 bolts.


b.

Tighten the 2 bolts in the order shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 37117B 10.INSTALL PROPELLER SHAFT HEAT INSULATOR (for AWD)

a.
A393782N01
0.521,0.365 0.823,0.542 0.302,0.177 10 true 1, 4 2.844,0.271 3,0.469 0.156,0.198 10 true 2 2.854,1.438 3.01,1.635 0.156,0.198 10 true 3

Temporarily install the propeller shaft heat insulator to the transfer assembly with the 3 bolts.


b.

Tighten the 3 bolts in the order shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


Hide 25591 11.INSTALL MANIFOLD SUPPORT BRACKET (for AWD)

a.
A393619C01
2.208,1.552 2.448,1.719 0.24,0.167 10 true *1 2.26,0.396 2.5,0.563 0.24,0.167 10 true *2 0.844,1.813 1.083,1.979 0.24,0.167 10 true *1
*1 Bolt (A)
*2 Bolt (B)


Temporarily install the manifold support bracket to the cylinder block sub-assembly and exhaust manifold converter sub-assembly (TWC: Front Catalyst) with the 3 bolts.


b.

Temporarily tighten the 2 bolts (A).


c.

Tighten the bolt (B).

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


d.

Tighten the 2 bolts (A).

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 17163 12.INSTALL NO. 1 HEAT INSULATOR BRACKET (for 2WD)

HINT:

Perform this procedure when it is necessary to replace the No. 1 heat insulator bracket.


a.

Install the No. 1 heat insulator bracket to the cylinder block sub-assembly with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


b.
A351367

Temporarily install the manifold support bracket to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the 3 bolts.

NOTICE:

Tighten the 3 bolts until they contact the surface of the manifold support bracket.



c.

Tighten the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


d.
A446269C02
1.563,2.073 1.75,2.333 0.188,0.26 10 false *a 1.146,3.073 1.375,3.292 0.229,0.219 10 false *b 2.021,3.083 2.333,3.24 0.313,0.156 10 false *c 2.938,0.99 3.177,1.198 0.24,0.208 10 true 1 1.771,0.563 2.01,0.771 0.24,0.208 10 true 2
*a Bolt Position
*b Correct
*c Incorrect


Temporarily install the driveshaft heat insulator sub-assembly to the No. 1 heat insulator bracket and manifold support bracket with the bolt and nut as shown in the illustration.

NOTICE:
·

Tighten the nut and bolt until they contact the surface of the driveshaft heat insulator sub-assembly.

·

Do not install the drive shaft heat insulator sub-assembly in the uppermost position. If the drive shaft heat insulator sub-assembly is installed in the uppermost position, damage may occur due to stress from distortion caused by high temperatures.




e.
A351377N02
0.906,0.427 1.063,0.625 0.156,0.198 10 true 1 2.958,0.563 3.115,0.76 0.156,0.198 10 true 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


Hide 25591 13.INSTALL MANIFOLD SUPPORT BRACKET (for 2WD)

a.

Temporarily install the manifold support bracket to the cylinder block sub-assembly and exhaust manifold converter sub-assembly with the 3 bolts.

NOTICE:

Tighten the 3 bolts until they contact the surface of the manifold support bracket.



b.

Tighten the 3 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 12321B 14.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY (for 2WD)

a.
A446269C02
1.563,2.073 1.75,2.333 0.188,0.26 10 false *a 1.146,3.073 1.375,3.292 0.229,0.219 10 false *b 2.021,3.083 2.333,3.24 0.313,0.156 10 false *c 2.938,0.99 3.177,1.198 0.24,0.208 10 true 1 1.771,0.563 2.01,0.771 0.24,0.208 10 true 2
*a Bolt Position
*b Correct
*c Incorrect


Temporarily install the driveshaft heat insulator sub-assembly to the No. 1 heat insulator bracket and manifold support bracket with the bolt and nut as shown in the illustration.

NOTICE:
·

Tighten the nut and bolt until they contact the surface of the driveshaft heat insulator sub-assembly.

·

Do not install the drive shaft heat insulator sub-assembly in the uppermost position. If the drive shaft heat insulator sub-assembly is installed in the uppermost position, damage may occur due to stress from distortion caused by high temperatures.




b.
A351377N02
0.906,0.427 1.063,0.625 0.156,0.198 10 true 1 2.958,0.563 3.115,0.76 0.156,0.198 10 true 2

Tighten the bolt and nut in the order shown in the illustration.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


Hide 58151 15.INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

a.

Install the front No. 1 floor heat insulator to the vehicle body with 3 nuts.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 17410 16.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for 2WD)

a.
A128853

Using a vernier caliper, measure the free length of the compression springs.

Standard Length Front Side 43 mm (1.69 in.)
Rear Side 40 mm (1.57 in.)
Minimum Free Length Front Side 41.5 mm (1.63 in.)
Rear Side 38.5 mm (1.52 in.)

If the free length is less than the minimum, replace the compression spring.


b.

Temporarily install 2 new exhaust pipe gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).


c.
A181728C96
2.906,1.49 2.781,1.49 2.781,1.49 2.479,1.802 false 1.802,3.281 2.01,3.292 2.01,3.292 2.01,2.438 false 0.844,0.479 1.146,0.479 1.146,0.479 1.146,1.625 false 0.594,0.417 0.896,0.698 0.302,0.281 10 false *1 1.583,3.208 1.865,3.417 0.281,0.208 10 false *2 3.01,1.427 3.281,1.698 0.271,0.271 10 false *a
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) or Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Exhaust Pipe Gasket
*a Wooden Block


Using a plastic hammer and wooden block, tap in the exhaust pipe gasket until its surface is flush with the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst).

NOTICE:
·

Be sure to install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket by using the exhaust pipe when connecting it.




d.

Install the front exhaust pipe assembly (TWC: Rear Catalyst) to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and tail exhaust pipe assembly with the 4 compression springs and 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
A258941C38
2.396,0.802 2.51,0.167 2.51,0.167 2.677,0.167 false 0.771,0.229 0.906,0.229 0.906,0.229 1.177,0.604 false 0.781,1.188 0.938,1.188 0.938,1.188 1.083,0.885 false 0.417,1.427 0.844,1.615 0.427,0.188 10 false *a 0.583,0.177 0.948,0.375 0.365,0.198 10 false *1 0.594,1.125 0.917,1.313 0.323,0.188 10 false *2 2.708,0.115 3.083,0.292 0.375,0.177 10 false *3
*1 Exhaust Manifold Converter Sub-assembly (TWC: Front Catalyst) or Front Exhaust Pipe Assembly (TWC: Rear Catalyst)
*2 Front Exhaust Pipe Assembly (TWC: Rear Catalyst) or Tail Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between Flanges:
- Front Side: 8.5 mm (0.335 in.)
- Rear Side: 6.5 mm (0.256 in.)


·

After installation, check that the space between the flanges of the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly (TWC: Rear Catalyst) is consistent front-to-rear and left-to-right.

·

After installation, check that the space between the flanges of the front exhaust pipe assembly (TWC: Rear Catalyst) and tail exhaust pipe assembly is consistent front-to-rear and left-to-right.




e.

Engage the wire harness clamp.


f.

Connect the heated oxygen sensor connector.


Hide 17410 17.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for AWD)

a.

Temporarily install new exhaust pipe gasket to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and front exhaust pipe assembly.


b.

Install the front exhaust pipe assembly to the exhaust manifold converter sub-assembly (TWC: Front Catalyst) with 2 new nuts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


c.

Engage the wire harness clamp.


d.

Connect the heated oxygen sensor connector.


Hide 17420K 18.INSTALL NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for AWD)

a.

Temporarily install 2 new exhaust pipe gaskets to the front exhaust pipe assembly and tail exhaust pipe assembly.


b.

Connect the No. 2 center exhaust pipe assembly (TWC: Rear Catalyst) to the 4 exhaust pipe supports.


c.

Install the No. 2 center exhaust pipe assembly (TWC: Rear Catalyst) to the front exhaust pipe assembly and tail exhaust pipe assembly with the 4 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 58165B 21.INSTALL FRONT FLOOR COVER RH (w/ Cover)

HINT:

Perform the same procedure as for the front floor cover LH.


Hide 12611 22.INSTALL NO. 1 ENGINE COVER

a.

Install the No. 1 engine cover to the cylinder head cover sub-assembly and cylinder head sub-assembly.


Hide 17301C 24.INSTALL INLET NO. 1 AIR DUCT SUB-ASSEMBLY

a.

Connect the inlet No. 1 air duct sub-assembly to the turbocharger sub-assembly.


b.

Tighten the hose clamp.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.

Connect the No. 2 vacuum transmitting hose assembly to the turbocharger sub-assembly.


d.

Connect the intake air control valve (air by-pass valve assembly) connector.


e.

Connect the inlet No. 1 air duct sub-assembly to the fuel pump protector with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


f.

Connect the No. 1 vacuum transmitting hose assembly to the vacuum pump assembly.


g.

Install the vacuum tank to the inlet No. 1 air duct sub-assembly with the 2 bolts.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


h.

Connect the No. 1 vacuum transmitting hose assembly to the vacuum tank.


Hide 25819 25.INSTALL VACUUM REGULATING VALVE ASSEMBLY

a.

Connect the No. 2 vacuum transmitting hose and No. 3 vacuum transmitting hose to the vacuum regulating valve assembly.


b.

Install the vacuum regulating valve assembly and No. 2 vacuum switching valve bracket to the cylinder head sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 17360A 26.INSTALL AIR TUBE ASSEMBLY

a.

Connect the air tube assembly to the turbocharger sub-assembly.


b.

Tighten the hose clamp.

Torque:
6.3 N*m (64 kgf*cm, 56 in.*lbf)


c.

Connect the No. 2 intercooler water hose and No. 3 intercooler water hose to the No. 1 water hose clamp bracket.


d.

Connect the No. 2 intercooler water hose and No. 3 intercooler water hose to the turbocharger sub-assembly and slide the 2 clips to secure them.


Hide 12217 27.INSTALL VENTILATION EJECTOR

a.

Apply a light coat of engine oil to the O-ring.

NOTICE:

When reusing the ventilation ejector, inspect the O-ring.



b.

Install the O-ring to the cylinder head cover sub-assembly.


c.
A393613

Install the ventilation ejector and air tube assembly to the cylinder head cover sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 12261 28.INSTALL VENTILATION HOSE

a.

Install the ventilation hose to the cylinder head cover sub-assembly and inlet No. 1 air duct sub-assembly and slide the 2 clips to secure it.


b.

Install the No. 4 ventilation hose to the ventilation ejector and inlet No. 1 air duct sub-assembly and slide the 2 clips to secure it.


Hide 82121 29.INSTALL ENGINE WIRE

a.

Install the wire harness clamp bracket to the cylinder head sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
A353510C03
0,0 0,0 false
V100135

Bolt
V100136

Nut
V100137

Connector


Engage the 3 wire harness clamps.


c.

Install the bolt and nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Connect the 7 connectors.


Hide 17705 30.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

Hide 17751 31.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 32.INSTALL RADIATOR COVER

Hide 55225 33.INSTALL DASH PANEL HEAT INSULATOR

Hide 55701J 34.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 35.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55735C 36.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55736D 37.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 38.INSTALL WATER GUARD PLATE LH (for TMC Made RHD)

Hide 55737B 39.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 40.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 42.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

a.

Perform Inspection After Repair after repairing an exhaust gas leak.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION