Home › Engine / Hybrid System › 8NR-FTS (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM32H0E _51 Engine / Hybrid System _059498 8NR-FTS ENGINE MECHANICAL _0291517 ENGINE ASSEMBLY A

8NR-FTS ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


HINT:

Perform "Inspection After Repair" after replacing the engine assembly.

Click hereEngine / Hybrid System>8NR-FTS (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


PROCEDURE

Hide 2.REMOVE ENGINE ASSEMBLY FROM ENGINE STAND

a.

Remove the engine assembly from the engine stand.


Hide 88310 3.INSTALL COMPRESSOR WITH PULLEY ASSEMBLY

Hide 16620 5.INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

a.

Install the V-ribbed belt tensioner assembly to the timing chain cover assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16361A 6.INSTALL FAN AND GENERATOR V BELT

Hide 32101B 7.INSTALL DRIVE PLATE AND RING GEAR SUB-ASSEMBLY (for CVT)

Hide 13405 8.INSTALL FLYWHEEL SUB-ASSEMBLY (for Manual Transaxle)

Hide 31250 9.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transaxle)

Hide 82121 12.INSTALL ENGINE WIRE

a.

Connect all the connectors and clamps, and install the engine wire to the engine assembly with transaxle.


Hide 11363A 13.INSTALL FLYWHEEL HOUSING SIDE COVER

a.

Install the flywheel housing side cover to the cylinder block sub-assembly.


Hide 28100 14.INSTALL STARTER ASSEMBLY

Hide 15.INSTALL WATER HOSE (for CVT)

a.

Install the water hose to the engine assembly with transaxle and slide the 5 clips to secure it.


b.

Engage the 3 clamps to the engine assembly with transaxle.


Hide 16.INSTALL WATER HOSE (for Manual Transaxle)

a.

Install the water hose to the engine assembly with transaxle and slide the 3 clips to secure it.


b.

Engage the 3 clamps to the engine assembly with transaxle.


Hide 12305 17.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Perform this procedure only when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A392295C01
1.24,1.594 1.854,1.823 0.615,0.229 10 true 1 (*a), 3 1.302,0.302 1.458,0.5 0.156,0.198 10 true 4 2.833,1.333 2.99,1.531 0.156,0.198 10 true 2
*a Temporarily Tighten


Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


c.

for DENSO Made:

i.

Connect the air conditioner tube and accessory to the engine mounting insulator sub-assembly RH with the bolt and nut.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



d.

for VALEO Made:

i.

Connect the air conditioner tube and accessory to the engine mounting insulator sub-assembly RH with the bolt and nut.

Torque:
Bolt : 9.8 N*m (100 kgf*cm, 87 in.*lbf)
Nut : 5.4 N*m (55 kgf*cm, 48 in.*lbf)



e.

Install the No. 2 earth wire to the engine mounting insulator sub-assembly RH and vehicle with the 2 bolts.

Torque:
10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 12372A 18.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Perform this procedure only when replacement of the engine mounting insulator LH is necessary.


a.
A392296C02
0,0 0.333,0.292 0.333,0.292 12 true *A 0.01,2.427 0.354,2.729 0.344,0.302 12 true *B 0.781,1.49 0.938,1.688 0.156,0.198 10 true 3 2.542,1.042 2.698,1.24 0.156,0.198 10 true 4 2.604,1.813 2.76,2.01 0.156,0.198 10 true 2 1.5,0.083 1.656,0.281 0.156,0.198 10 true 6 0.49,0.448 1.146,0.677 0.656,0.229 10 true 1 (*a), 5 0.51,2.896 1.167,3.125 0.656,0.229 10 true 1 (*a), 5 0.813,4.01 0.969,4.208 0.156,0.198 10 true 3 2.542,4.375 2.698,4.573 0.156,0.198 10 true 2 2.542,3.563 2.698,3.76 0.156,0.198 10 true 4 1.542,2.51 1.698,2.708 0.156,0.198 10 true 6
*A for CVT
*B for Manual Transaxle
*a Temporarily Tighten


Temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 4 bolts and nut in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 20.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the cylinder head sub-assembly with the bolt.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


b.

Install the engine wire to the wire harness clamp bracket with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Engage the 3 clamps.


Hide 21.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.

Operate the engine lifter and install the engine assembly with transaxle to the vehicle.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.

Connect the front suspension crossmember sub-assembly to the vehicle with the 6 bolts.

Torque:
141 N*m (1438 kgf*cm, 104 ft.*lbf)


d.

Install the engine mounting insulator LH to the engine mounting bracket LH with the bolt and nut.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)

NOTICE:

While holding the nut in place, tighten the bolt.



e.

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 51108A 22.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY LH

Hide 51107A 23.INSTALL REAR SIDE RAIL REINFORCEMENT SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 31481A 26.CONNECT NO. 1 CLUTCH HOSE (for Manual Transaxle)

a.

Connect the No. 1 clutch hose to the clutch flexible hose bracket with a new clip.


b.
A393394C01
2.156,2.156 1.667,1.375 true 2.219,2.125 2.531,2.281 0.313,0.156 10 false *a 1.125,2.208 1.438,2.365 0.313,0.156 10 false *b
*a 10 mm Union Nut Wrench
*b Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the bleeder clutch release tube to the No. 1 clutch hose.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a 10 mm union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 37100 28.INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for AWD)

Hide 17410 29.INSTALL FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for 2WD)

Hide 17410 30.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for AWD)

Hide 17420K 31.INSTALL NO. 2 CENTER EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst) (for AWD)

Hide 57533B 32.INSTALL FRONT FLOOR CENTER BRACE (for 2WD)

Hide 57533B 33.INSTALL FRONT FLOOR CENTER BRACE (for AWD)

Hide 58166 34.INSTALL FRONT FLOOR COVER LH (w/ Cover)

Hide 58165B 35.INSTALL FRONT FLOOR COVER RH (w/ Cover)

HINT:

Use the same procedure as for the LH side.


Hide 45025D 36.CONNECT NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY

Hide 45260 37.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 38.INSTALL COLUMN HOLE COVER SILENCER SHEET

Hide 88704 39.CONNECT SUCTION HOSE SUB-ASSEMBLY

Hide 88703 40.CONNECT DISCHARGE HOSE SUB-ASSEMBLY

Hide 23829A 44.CONNECT FUEL VAPOR FEED HOSE

a.

Connect the fuel vapor feed hose to the fuel vapor feed pipe and slide the clip to secure it.


Hide 44750 45.CONNECT UNION TO CONNECTOR TUBE HOSE

Hide 33820B 46.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for CVT)

Hide 33820B 47.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY (for Manual Transaxle)

Hide 16554C 48.CONNECT NO. 4 INTERCOOLER COOLING WATER HOSE

Hide 16551C 49.CONNECT NO. 1 INTERCOOLER COOLING WATER HOSE

Hide 16572D 50.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet with thermostat sub-assembly and slide the clip to secure it.


Hide 16571C 51.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the water outlet and slide the clip to secure it.


Hide 74404A 52.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly to the vehicle with the 3 bolts.

Torque:
15.4 N*m (157 kgf*cm, 11 ft.*lbf)


b.

Engage the clamp to connect the engine wire to the battery clamp sub-assembly.


Hide 53.CONNECT WIRE HARNESS

a.

Connect the engine wire to the transaxle assembly with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


b.

Connect the engine wire to the positive (+) battery terminal with the 3 nuts.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


c.

Connect the engine wire to the battery clamp sub-assembly with the bolt and nut.

Torque:
7.0 N*m (71 kgf*cm, 62 in.*lbf)


d.
A397427C01
2.719,0.427 3.094,0.667 0.375,0.24 12 false *A 2.729,1.042 3.104,1.281 0.375,0.24 12 false *B
*A for Type A
*B for Type B


Connect the engine wire to the vehicle with the 2 bolts.

Torque:
for Type A : 8.5 N*m (87 kgf*cm, 75 in.*lbf)
for Type B : 10.5 N*m (107 kgf*cm, 8 ft.*lbf)


Hide 17701 55.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly to the vehicle with the 2 bolts.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 17705 56.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

a.

Connect the air cleaner cap with air cleaner hose and tighten the hose clamp.

Torque:
2.0 N*m (20 kgf*cm, 18 in.*lbf)


b.

Engage the 2 guides to install the air cleaner cap sub-assembly to the air cleaner case sub-assembly.


c.

Engage the 2 air cleaner cap sub-assembly clamps to install the air cleaner cap sub-assembly.


d.

Engage the clamp to the air cleaner cap sub-assembly.


e.

Connect the mass air flow meter connector.


Hide 17751 57.INSTALL NO. 1 AIR CLEANER INLET

Hide 53141F 58.INSTALL RADIATOR COVER

Hide 55701J 59.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55701J 60.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 55735C 61.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55736D 62.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 63.INSTALL WATER GUARD PLATE LH (for TMC Made RHD)

Hide 55737B 64.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 65.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 28800 66.INSTALL BATTERY

Hide 67.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 68. INITIALIZATION AFTER RECONNECTING AUXILIARY BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 69.BLEED CLUTCH LINE (for Manual Transaxle)

Hide 72.ADD COOLANT (for Intercooler)

Hide 73.ADD MANUAL TRANSAXLE OIL (for Manual Transaxle)

Hide 75.ADD TRANSFER OIL (for AWD)

Hide 76.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT

Hide 77. WARM UP ENGINE

a.

Keep the A/C switch on for at least 2 minutes to warm up the compressor.

NOTICE:

To prevent damage to the compressor, be sure to warm up the compressor when turning the air conditioning on after removing and installing any air conditioning system lines (including the compressor).



Hide 79.ADJUST SHIFT LEVER POSITION (for Manual Transaxle)

Hide 82.INSPECT FOR ENGINE OIL LEAK

Hide 85.INSPECT FOR CONTINUOUSLY VARIABLE TRANSAXLE FLUID LEAK (for CVT)

Hide 86.INSPECT MANUAL TRANSAXLE OIL LEAK (for Manual Transaxle)

Hide 91.INSPECT ENGINE COOLANT LEVEL IN RESERVOIR

Hide 51444A 92.INSTALL REAR ENGINE UNDER COVER LH

a.

Install the rear engine under cover LH to the vehicle with the 6 clips.


Hide 51443C 93.INSTALL REAR ENGINE UNDER COVER RH

a.

Install the rear engine under cover RH to the vehicle with the 6 clips.


Hide 51441 94.INSTALL NO. 1 ENGINE UNDER COVER

a.
A390450C01
0.854,0 1.083,0.198 0.229,0.198 10 true *1 1.396,0.01 1.625,0.208 0.229,0.198 10 true *1 1.875,0.01 2.104,0.208 0.229,0.198 10 true *1 2.417,0 2.646,0.198 0.229,0.198 10 true *1
*1 Bolt


Install the No. 1 engine under cover to the vehicle with the 4 bolts, 4 screws and 4 clips.

Torque:
Bolt : 7.5 N*m (76 kgf*cm, 66 in.*lbf)


Hide 95.INSTALL FRONT WHEELS

Hide 96. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 97.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT