Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (for RHD) › from 2020.08
RM32H0E _54 Brake _060039 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0298589 BRAKE ACTUATOR(for RHD) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(for RHD)  INSTALLATION  


PROCEDURE

Hide 77286D 1.INSTALL NO. 2 FUEL TUBE CLAMP

a.

Engage the claw to install the No. 2 fuel tube clamp to the brake actuator bracket assembly.


Hide 44547B 2.INSTALL BRAKE ACTUATOR BRACKET CUSHION

a.

Install the brake actuator bracket cushion to the brake actuator bracket assembly.


Hide 44521A 3.INSTALL NO. 1 BRAKE ACTUATOR CASE COLLAR

a.

Install the No. 1 brake actuator case collar to the brake actuator bracket cushion.


Hide 44510 4.INSTALL BRAKE ACTUATOR ASSEMBLY

a.

Temporarily install the brake actuator assembly with the 2 nuts and a new bolt.


b.
C366929N01
1.479,1.219 1.635,1.417 0.156,0.198 10 true 1 2.948,1.167 3.104,1.365 0.156,0.198 10 true 2 0.729,1.74 0.885,1.938 0.156,0.198 10 true 3

Fully tighten the 2 nuts and bolt in the order shown in the illustration.

Torque:
6.5 N*m (66 kgf*cm, 58 in.*lbf)

NOTICE:
·

Do not remove the hole plugs of a new brake actuator assembly before connecting the brake tubes because the brake actuator assembly is filled with brake fluid.

·

Do not hold the brake actuator assembly by the connector.




Hide 5.INSTALL BRAKE ACTUATOR WITH BRACKET

a.

Temporarily install the brake actuator with bracket to the vehicle body with the bolt and 2 nuts.


b.
C366928N01
2.51,1.917 2.667,2.115 0.156,0.198 10 true 1 1.906,1.906 2.063,2.104 0.156,0.198 10 true 3 1.51,1.771 1.667,1.969 0.156,0.198 10 true 2

Fully tighten the bolt and 2 nuts in the order shown in the illustration.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Do not damage the brake tubes.



c.

Engage the 2 clamps to install the fuel main tube and fuel tank to canister tube to the No. 2 fuel tube clamp.


d.
C369565C01
1.24,1.792 1.375,1.448 true 1.917,1.271 2.469,1.427 true 1.875,0.875 2.438,0.74 true 1.646,0.927 2.083,0.458 true 0.667,1.125 1.063,1.125 true 0.677,0.792 1.302,1.042 true 1.125,1.844 1.385,2.042 0.26,0.198 10 true *a 2.521,1.365 2.75,1.615 0.229,0.25 10 true *b 2.469,0.615 2.698,0.823 0.229,0.208 10 true *c 2.125,0.344 2.365,0.531 0.24,0.188 10 true *d 0.438,0.688 0.646,0.896 0.208,0.208 10 true *e 0.427,1.052 0.656,1.24 0.229,0.188 10 true *f
*a From 1st Chamber of Brake Booster with Master Cylinder Assembly
*b From 2nd Chamber of Brake Booster with Master Cylinder Assembly
*c To Front Wheel Cylinder Assembly LH
*d To Rear Wheel Cylinder Assembly RH
*e To Rear Wheel Cylinder Assembly LH
*f To Front Wheel Cylinder Assembly RH


Temporarily tighten each brake tube to the correct position on the brake actuator assembly as shown in the illustration.


e.
C366927C01
1.781,2.885 2.094,3.042 0.313,0.156 10 false *a 0.354,1.021 0.615,1.24 0.26,0.219 10 true (A) 0.74,0.604 1,0.823 0.26,0.219 10 true (A) 1.521,0.406 1.781,0.625 0.26,0.219 10 true (A) 2.271,0.573 2.531,0.792 0.26,0.219 10 true (A) 2.281,0.948 2.542,1.167 0.26,0.219 10 true (B) 0.76,1.573 1.021,1.792 0.26,0.219 10 true (B)
*a Torque Wrench Fulcrum Length


Using a 10 mm and 12 mm union nut wrench, connect the 6 brake tubes to the brake actuator assembly.

Torque:
Specified tightening torque (A) : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)
Specified tightening torque (B) : 19.5 N*m (199 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow the brake tubes to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (A): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)

·

When using a union nut wrench (fulcrum length of 20 mm (0.787 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)) (B): 17.4 N*m (177 kgf*cm, 13 ft.*lbf)




f.
C366910C01
1.729,2.906 2.042,3.063 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, connect the brake tube to the front flexible hose.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the brake tubes.

·

Do not allow the brake tubes to twist or interfere with other parts or the vehicle body during tightening.

·

Do not allow any foreign matter such as dirt or dust to enter the brake tubes from the connecting parts.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




g.
C366935C01
0,0 0,0 false
V113147

Connect the connector
V113148

Lock the lock lever


Connect the connector to the brake actuator assembly and lock the lock lever.

NOTICE:
·

Make sure that the actuator connector can be connected smoothly. Do not allow water, oil or dirt to enter the connector.

·

Make sure that the connector is locked securely.




Hide 86510A 6.INSTALL SECURITY HORN ASSEMBLY (w/ Security Horn)

Hide 55701J 8.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 55735C 9.INSTALL COWL BODY MOUNTING REINFORCEMENT RH

Hide 55736D 10.INSTALL COWL BODY MOUNTING REINFORCEMENT LH

Hide 55735A 11.INSTALL WATER GUARD PLATE LH (for TMC Made)

Hide 55737B 12.INSTALL NO. 1 HEATER AIR DUCT SPLASH SHIELD SEAL

Hide 13.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 14.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 15.BLEED BRAKE SYSTEM

Hide 19. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART