Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SIDE AIRBAG SENSOR (for Center Pillar) › from 2020.08
RM32H0E _58 Vehicle Interior _060061 SUPPLEMENTAL RESTRAINT SYSTEMS _0294201 SIDE AIRBAG SENSOR(for Center Pillar) A

SUPPLEMENTAL RESTRAINT SYSTEMS  SIDE AIRBAG SENSOR(for Center Pillar)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The following procedure is for LHD vehicles.

·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 89831E 1.INSTALL FLOOR SIDE AIRBAG SENSOR

a.

Check that the ignition switch off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:
B422343

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Connect the connector to the floor side airbag sensor.

B312074C38
2.271,0.823 2.552,0.615 false 2.417,1.01 3,0.792 true 3.052,0.677 3.26,0.885 0.208,0.208 10 false *a 5.938,3.365 6.25,3.521 0.313,0.156 10 false *b 2.615,0.438 2.948,0.667 0.333,0.229 10 false (A)
*a White Housing Lock *b Connection is completed


NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


HINT:
·

Be sure to connect the connector until it is locked (when locking, make sure that a click sound can be heard).

·

When the connector is locked, the white housing lock will slide. Do not hold the white housing lock or the part (A) as it may result in an insecure connection.




d.

Before connecting the connector, check that the position of the white housing lock is as shown in the illustration.

B296255C05
4.76,1.833 5.031,2.104 0.271,0.271 10 false *b 1.396,1.833 1.677,2.115 0.281,0.281 10 false *b 4.76,0.573 5.031,0.875 0.271,0.302 10 false *a 1.396,0.573 1.677,0.865 0.281,0.292 10 false *a
*a Incorrect *b Correct



e.
B458401

Engage the claw to install the floor side airbag sensor with the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the floor side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.

·

When installing the floor side airbag sensor, make sure that the SRS wiring does not interfere with or is not pinched between other parts.

·

Make sure that the floor side airbag sensor claw is securely inserted into the body hole.




f.

Check that there is no looseness in the installed parts of the floor side airbag sensor.


Hide 62414A 2.INSTALL CENTER PILLAR LOWER GARNISH

Hide 62332A 3.CONNECT REAR DOOR OPENING TRIM WEATHERSTRIP

Hide 67918A 4.INSTALL REAR DOOR SCUFF PLATE

Hide 62312B 5.CONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP

Hide 67914 6.INSTALL FRONT DOOR SCUFF PLATE

Hide 73220 7.CONNECT FRONT SEAT OUTER BELT ASSEMBLY

Hide 73233 8.INSTALL LAP BELT OUTER ANCHOR COVER

Hide 9.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 10. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART