PROBLEM SYMPTOMS TABLE
Troubleshooting · Vehicles built from Jun 2009
Versions by build date: Oct 2006 – May 2009 from Jun 2009
Inspect the suspected areas in numerical order by referring to the corresponding pages when any of the following symptoms occurs:
| Symptom |
Suspected Area |
See page |
| Steering wheel cannot be unlocked (the engine cannot be started). |
1. Initialization |
Click here
|
| 2. Check for DTCs in the smart entry and start system (for 2GR-FE). |
Click here
|
|
| 3. Check for DTCs in the smart entry and start system (for 2AZ-FE). |
Click here
|
|
| 4. Check for DTCs in the engine immobiliser system. |
Click here
|
|
| 5. Check that the Lck/Unlck Rec item in the DATA LIST of the certification ECU displays YES within 10 seconds after starting the engine. (If it displays NO, see "No steering unlock command" in this table.) |
Click here
|
|
| 6. Check the input signal from the IGE terminal of the steering lock ECU. |
Click here
|
|
| 7. Steering lock ECU power source circuit. |
Click here
|
|
| 8. Replace the steering lock ECU. |
Click here
|
|
| Steering wheel cannot be unlocked (no steering unlock command). |
1. Check that the S Code Chk item in the DATA LIST of the certification ECU displays OK. (If it displays NG, replace the ID code box.) |
- |
| 2. Check that the L Code Chk item in the DATA LIST of the certification ECU displays OK. (If it displays NG, replace the ID code box.) |
- |
|
| 3. Replace the certification ECU. |
- |
|
| Steering wheel cannot be locked. |
1. Check for DTCs in the smart entry and start system (for 2GR-FE). |
Click here
|
| 2. Check for DTCs in the smart entry and start system (for 2AZ-FE). |
Click here
|
|
| 3. Check for DTCs in the engine immobiliser system. |
Click here
|
|
| 4. With the engine switch off and the shift lever in the P position, open and close the drivers door. After that, check that the Lck/Unlck Rec item in the DATA LIST of the certification ECU displays YES within 10 seconds. (If it displays NO, see "No steering lock command" in this table.) |
Click here
|
|
| 5. Check the input signal from the IGE terminal of the steering lock ECU. |
Click here
|
|
| 6. Steering lock ECU power source circuit. |
Click here
|
|
| 7. Replace the steering lock ECU. |
Click here
|
|
| Steering wheel cannot be locked (no steering lock command). |
1. Courtesy light switch circuit |
Click here
|
| 2. Check that the S Code Chk item in the DATA LIST of the certification ECU displays OK. (If it displays NG, replace the ID code box.) |
- |
|
| 3. Check that the L Code Chk item in the DATA LIST of the certification ECU displays OK. (If it displays NG, replace the ID code box.) |
- |
|
| 4. Replace the certification ECU. |
- |
| Symptom |
Suspected Area |
See page |
| Engine does not start. |
1. Initialization |
Click here
|
| 2. Check for DTCs in the smart entry and start system (for 2GR-FE). |
Click here
|
|
| 3. Check for DTCs in the smart entry and start system (for 2AZ-FE). |
Click here
|
|
| 4. Check for DTCs in the engine immobiliser system. |
Click here
|
|
| 5. Check that the engine switch is turned on (IG). |
- |
|
| 6. Check cranking operation. (If cranking operation is possible, see "Engine does not start due to the engine immobiliser" in this table.) |
- |
|
| 7. Check Shift P Sig in the DATA LIST of the main body ECU and confirm that the shift signal is normal. |
- |
|
| 8. Check whether the steering wheel is locked or unlocked. (If it is locked, see "Steering wheel cannot be unlocked" in the steering lock function table.) |
- |
|
| 9. Check the output from the SLP terminal of the steering lock ECU. |
Click here
|
|
| 10. Check the output signal from the ST SW of the certification ECU (DTC B2275 for 2GR-FE). |
Click here
|
|
| 11. Check the output signal from the ST SW of the certification ECU (DTC B2275 for 2AZ-FE). |
Click here
|
|
| 12. Replace the main body ECU. |
- |
|
| Engine does not start due to the engine immobiliser. |
1. Check that the L Code Chk item in the DATA LIST of the certification ECU displays OK. (If it displays NG, replace the ID code box.) |
- |
| 2. Check that the Start Rqst item in the DATA LIST of the certification ECU displays YES. (If it displays NO, replace the certification ECU.) |
- |
|
| 3. Check that the S Code Chk item in the DATA LIST of the certification ECU displays OK. (If it displays NG, replace the ID code box.) |
- |
|
| 4. Replace the ID code box. |
- |