2006-2011 Camry Aurion · Service Manual BODY ELECTRICAL

Fuel Receiver Gauge Malfunction

Circuit diagnosis · Vehicles built from Jun 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

DESCRIPTION

  1. The meter CPU uses the fuel sender gauge assembly to determine the level of the fuel in the fuel tank. The resistance of the fuel sender gauge will vary between approximately 15 Ω with the float at the full position, and 410 Ω with the float at the empty position. The meter outputs battery voltage through two 820 Ω resistors that are mounted in parallel inside the meter ECU. The meter CPU measures the voltage between the variable resistor in the fuel sender gauge and the two resistors mounted in parallel in the meter. Voltage measured at this point will vary as the float of the fuel sender gauge is moved. The highest voltage observed should be approximately half of battery voltage.

HINT:
The fuel level warning light will come on when the fuel level is below 10.5 liters.


WIRING DIAGRAM

E128091E08
E128091E09

INSPECTION PROCEDURE


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if CAN communication DTC is output (Click here for LHD without Smart Entry and Start System, Click here for LHD with Smart Entry and Start System, Click here for RHD without Smart Entry and Start System, Click here for RHD with Smart Entry and Start System).


Result:
Result
Proceed to
CAN communication DTC is not output.
A
CAN communication DTC is output.
B (Click here for LHD without Smart Entry and Start System, Click here for LHD with Smart Entry and Start System, Click here for RHD without Smart Entry and Start System, Click here for RHD with Smart Entry and Start System)



B
GO TO CAN COMMUNICATION SYSTEM
A


2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / Combination Meter / Active Test.

  1. Check the operation by referring to the table below.

    Combination Meter: 
    Tester Display
    Test Part
    Control Range
    Normal Condition
    Fuel Meter Operation
    Fuel receiver gauge
    EMPTY, 1/2, FULL
    -

    OK:
    Needle indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


3. READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Ignition switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Body / Combination Meter / Data List.

  1. Check the values by referring to the table below.

    Combination Meter: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Fuel Input (*1)
    Fuel input signal Min.: 0, Max.: 127.5
    Fuel gauge indicates (F): 62.9 (L)
    Fuel gauge indicates (3/4): 52.5 (L)
    Fuel gauge indicates (1/2): 35.0 (L)
    Fuel gauge indicates (3/4): 17.5 (L)
    Fuel gauge indicates (E): 7.5 (L)
    -
    Fuel Input (*2)
    Fuel input signal Min.: 0 (0 L), Max.: 127.5 (70 L)
    Fuel gauge indicates (F): 62.9 (L)
    Fuel gauge indicates (3/4): 52.5 (L)
    Fuel gauge indicates (1/2): 35.0 (L)
    Fuel gauge indicates (3/4): 17.5 (L)
    Fuel gauge indicates (E): 7.5 (L)
    -
    *1: for 2AZ-FE*2: for 2GR-FE

    OK:
    Fuel value signal displayed on the tester is almost the same as needle indication.



NG
REPLACE COMBINATION METER ASSEMBLY
OK


4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - FUEL SENDER GAUGE ASSEMBLY)

  1. E134503E02
    for 2AZ-FE:
    1. Disconnect the F1 and N10 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F1-20 (FR) - N10-3
      Always
      Below 1 Ω
      F1-21 (FE) - N10-2
      Always
      Below 1 Ω
      N10-3 - Body ground
      Always
      10 kΩ or higher
      F1-21 (FE) - Body ground
      Always
      10 kΩ or higher

  1. E134471E02
    for 2GR-FE:
    1. Disconnect the F2 and N10 connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      F2-15 (FR) - N10-3
      Always
      Below 1 Ω
      F2-16 (FE) - N10-2
      Always
      Below 1 Ω
      N10-2 - Body ground
      Always
      10 kΩ or higher
      F2-16 - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. INSPECT FUEL SENDER GAUGE ASSEMBLY

  1. E128086E11
    Disconnect the fuel sender gauge connector.

  1. Remove the fuel sender gauge assembly.

  1. Check that the float moves smoothly between F and E.

  1. Measure the resistance between the terminals 2 (FE) and 3 (FR) of connector according to the value(s) in the table below.

    Standard resistance:
    Float Level
    Resistance (Ω)
    F
    13.5 to 16.5
    Between E and F
    13.5 to 414.5 (Gradually changes)
    E
    405.5 to 414.5



NG
REPLACE FUEL SENDER GAUGE ASSEMBLY
OK


6. REPLACE COMBINATION METER ASSEMBLY
  1. Replace the combination meter assembly with a new one or a normal one.

    OK:
    The operation of the combination meter assembly returns to normal.



NG
REPLACE ECM
OK

END


← Fuel Receiver Gauge Malfunction (Oct 2006 – May 2009)Engine Coolant Temperature Receiver Gauge Malfunction (Jun 2006 – Sep 2006) →