C1237/37 Speed Sensor Rotor Faulty
Diagnostic trouble codes · Vehicles built from Jun 2009
Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009
DESCRIPTION
The skid control ECU measures the speed of each wheel by receiving signals from the speed sensor.These signals are used for recognizing that all 4 wheels are operating properly.
Therefore, all wheel signals must be equal.
| DTC No. |
DTC Detecting Condition |
Trouble Area |
| C1237/37 |
When any of the following is detected:
|
|
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Check the condition of each related circuit connector before troubleshooting (Click here).
| 1. CHECK TIRES |
Check the size and condition of all 4 tires (Click here).
- HINT:
- This DTC is output when tire deformation or a difference in tire size is detected.
- OK:
- The diameters of all 4 tires and air pressure are the same.
|
|
||||
| OK | |
| 2. INSPECT SPEED SENSOR AND SENSOR ROTOR SERRATIONS |
Disconnect the skid control ECU connector.

Connect the oscilloscope to each speed sensor terminal of the skid control ECU connector.
- Terminals:
Connector
Circuit
A25-5 (FL+) - A25-6 (FL-)
Front left speed sensor
A25-10 (FR+) - A25-9 (FR-)
Front right speed sensor
A25-7 (RL+) - A25-17 (RL-)
Rear left speed sensor
A25-19 (RR+) - A25-8 (RR-)
Rear right speed sensor
Check that a waveform is output when the tires are rotated (by the sensor circuit).

- OK:
- A waveform as shown in the figure should be output.
- HINT:
- Each sensor circuit outputs the same waveform without noise.
- As vehicle speed (wheel rotation speed) increases, the width of the waveform narrows and the output voltage becomes greater.
- When noise is identified in the waveform on the oscilloscope, the erratic signals are generated due to rotor scratches, looseness or foreign matter attached to the speed sensor.
- Each sensor circuit outputs the same waveform without noise.
Make sure that the waveform does not change while jiggling a connector or a wire harness.
- OK:
- The waveform does not change.
- HINT:
- If the waveform changes while jiggling a connector or a wire harness, there may be a malfunction in the connector or the wire harness.
Connect the connector.
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at a speed of 32 km/h (20 mph) or more for 60 seconds or more.
Check if the same DTC is recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
| 4. CHECK SPEED SENSOR ROTOR |
Check the speed sensor rotor.Front Speed Sensor Rotor (Front drive outboard joint shaft assembly): (Click here)Rear Speed Sensor Rotor (Rear axle hub and bearing assembly): (Click here)
- OK:
- No scratches or foreign matter on the rotors.
- NOTICE:
- Check the speed sensor signal after the cleaning/replacement (Click here).
|
|
||||
| OK | |
| 5. CHECK SPEED SENSOR TIP |
Remove each speed sensor (Click here for front, Click here for rear).
Check the speed sensor tip.
- OK:
- No scratches or foreign matter on the sensor tip.
- NOTICE:
- Check the speed sensor signal after the cleaning/replacement (Click here).
Install the speed sensor.
|
|
||||
| OK | |
| 6. INSPECT EACH SPEED SENSOR |
Disconnect each speed sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- FRONT:
Tester Connection
Condition
Specified Condition
A14-1 (FL+) - A14-2 (FL-)
Always
1.4 to 1.8 kΩ at 20°C (68°F)
A14-1 (FL+) - Body ground
Always
10 kΩ or higher
A14-2 (FL-) - Body ground
Always
10 kΩ or higher
A35-1 (FR+) - A35-2 (FR-)
Always
1.4 to 1.8 kΩ at 20°C (68°F)
A35-1 (FR+) - Body ground
Always
10 kΩ or higher
A35-2 (FR-) - Body ground
Always
10 kΩ or higher
- REAR:
Tester Connection
Condition
Specified Condition
g1-2 (RL+) - g1-1 (RL-)
Always
Below 2.2 kΩ
g1-2 (RL+) - Body ground
Always
10 kΩ or higher
g1-1 (RL-) - Body ground
Always
10 kΩ or higher
f1-2 (RR+) - f1-1 (RR-)
Always
Below 2.2 kΩ
f1-2 (RR+) - Body ground
Always
10 kΩ or higher
f1-1 (RR-) - Body ground
Always
10 kΩ or higher
Connect the connector.
- NOTICE:
- Check the speed sensor signal after replacement (Click here).
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU TO EACH SPEED SENSOR) |
Disconnect the skid control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard resistance:
- FRONT:
Tester Connection
Condition
Specified Condition
A25-5 (FL+) - A14-1 (FL+)
Always
Below 1 Ω
A25-6 (FL-) - A14-2 (FL-)
Always
Below 1 Ω
A25-10 (FR+) - A35-1 (FR+)
Always
Below 1 Ω
A25-9 (FR-) - A35-2 (FR-)
Always
Below 1 Ω
A25-5 (FL+) - Body ground
Always
10 kΩ or higher
A25-6 (FL-) - Body ground
Always
10 kΩ or higher
A25-10 (FR+) - Body ground
Always
10 kΩ or higher
A25-9 (FR-) - Body ground
Always
10 kΩ or higher
- REAR:
Tester Connection
Condition
Specified Condition
A25-7 (RL+) - g1-2 (RL+)
Always
Below 1 Ω
A25-17 (RL-) - g1-1 (RL-)
Always
Below 1 Ω
A25-19 (RR+) - f1-2 (RR+)
Always
Below 1 Ω
A25-8 (RR-) - f1-1 (RR-)
Always
Below 1 Ω
A25-7 (RL+) - Body ground
Always
10 kΩ or higher
A25-17 (RL-) - Body ground
Always
10 kΩ or higher
A25-19 (RR+) - Body ground
Always
10 kΩ or higher
A25-8 (RR-) - Body ground
Always
10 kΩ or higher
Connect the connector.
|
|
||||
| OK | |
| 8. RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at the speed of 32 km/h (20 mph) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
- HINT:
- Reinstall the sensors, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.
- Result:
Condition
Proceed to
DTC (C1237/37) is not output
A
DTC (C1237/37) is output
B
|
|
||||
| A | ||
| ||
