DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |
DTC P0305 Cylinder 5 Misfire Detected |
DTC P0306 Cylinder 6 Misfire Detected |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | Simultaneous misfiring of several cylinders occurs and one of the following conditions is detected (2 trip detection logic):
|
|
| P0301 P0302 P0303 P0304 P0305 P0306 | Misfiring of specific cylinder occurs and one of the following conditions is detected (2 trip detection logic):
|

| Engine Speed | Duration |
| Idling | 5 minutes or more |
| 1000 | 4 minutes or more |
| 2000 | 3 minutes or more |
| 3000 | 2 minutes or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 are output | A |
| DTC P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 3.CHECK PCV HOSE (HOSE CONNECTIONS) |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 4.READ VALUE USING INTELLIGENT TESTER (CATALYST OT MF F/C) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Catalyst OT MF F/C.
Read the value displayed on the tester.
| Data List | Tester Display | Proceed to |
| Catalyst OT MF F/C | Avail | A |
| Not Avl | B |
|
| ||||
| A | |
| 5.PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and turn the tester on.
Enter the following menus: Powertrain / Engine / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.
Perform the Active Test.
| NEXT | |
| 6.READ VALUE USING INTELLIGENT TESTER (CYLINDER #1 (TO #6) MISFIRE COUNT) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on (Step "A").
Enter the following menus: Powertrain / Engine / Data List / Cylinder #1 (to #6) Misfire Count (Step "B").
Read each value for Cylinder #1 (to #6) Misfire Count displayed on the tester. If no misfire counts occur in any cylinders, perform the following procedure:
Start the engine and let it idle.
Move the shift lever to D.
Check the Cylinder #1 (to #6) Misfire Count.
If misfire counts are still not displayed, perform steps ("A") and ("B").
Drive the vehicle while satisfying the Misfire RPM and Misfire Load values noted in the "Read Value Using Intelligent Tester (Misfire RPM and Misfire Load)" procedure above.
Read Cylinder #1 (to #6) Misfire Count or the DTCs displayed on the tester.
| Misfire Count | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 7.CHECK SPARK PLUG |
![]() |
Remove the ignition coil assembly and the spark plug of the misfiring cylinder.
Measure the spark plug electrode gap.
Check the electrode for carbon deposits.
| Manufacturer | Product |
| DENSO | FK20HR11 |
Reinstall the ignition coil assembly and the spark plug.
|
| ||||
| OK | |
| 8.CHECK FOR SPARK AND IGNITION (SPARK TEST) |
Perform a spark test.
Remove the ignition coil assembly from the cylinder head.
Install the spark plug onto the ignition coil assembly.
Disconnect the 6 fuel injector assembly connectors.
Touch the spark plug to the cylinder head.
Crank the engine for less than 2 seconds and check for spark.
Reconnect the 6 fuel injector assembly connectors.
Install the ignition coil assembly.
|
| ||||
| OK | |
| 9.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 10.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C7-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C9-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C8-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C10-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C36-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C37-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
Reconnect the fuel injector assembly connectors.
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
![]() |
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| #10 (C58-45) - C7-1 | Below 1 Ω |
| #20 (C58-85) - C9-1 | Below 1 Ω |
| #30 (C58-44) - C8-1 | Below 1 Ω |
| #40 (C58-84) - C10-1 | Below 1 Ω |
| #50 (C58-43) - C36-1 | Below 1 Ω |
| #60 (C58-83) - C37-1 | Below 1 Ω |
| #10 (C58-45) or C7-1 - Body ground | 10 kΩ or higher |
| #20 (C58-85) or C9-1 - Body ground | 10 kΩ or higher |
| #30 (C58-44) or C8-1 - Body ground | 10 kΩ or higher |
| #40 (C58-84) or C10-1 - Body ground | 10 kΩ or higher |
| #50 (C58-43) or C36-1 - Body ground | 10 kΩ or higher |
| #60 (C58-83) or C37-1 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| #10 (C55-45) - C7-1 | Below 1 Ω |
| #20 (C55-85) - C9-1 | Below 1 Ω |
| #30 (C55-44) - C8-1 | Below 1 Ω |
| #40 (C55-84) - C10-1 | Below 1 Ω |
| #50 (C55-43) - C36-1 | Below 1 Ω |
| #60 (C55-83) - C37-1 | Below 1 Ω |
| #10 (C55-45) or C7-1 - Body ground | 10 kΩ or higher |
| #20 (C55-85) or C9-1 - Body ground | 10 kΩ or higher |
| #30 (C55-44) or C8-1 - Body ground | 10 kΩ or higher |
| #40 (C55-84) or C10-1 - Body ground | 10 kΩ or higher |
| #50 (C55-43) or C36-1 - Body ground | 10 kΩ or higher |
| #60 (C55-83) or C37-1 - Body ground | 10 kΩ or higher |
Reconnect the fuel injector assembly connectors.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 12.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND/OR #60 VOLTAGE) |
![]() |
Disconnect the ECM connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| #10 (C58-45) - E01 (C58-22) | 11 to 14 V |
| #20 (C58-85) - E01 (C58-22) | 11 to 14 V |
| #30 (C58-44) - E01 (C58-22) | 11 to 14 V |
| #40 (C58-84) - E01 (C58-22) | 11 to 14 V |
| #50 (C58-43) - E01 (C58-22) | 11 to 14 V |
| #60 (C58-83) - E01 (C58-22) | 11 to 14 V |
| Tester Connection | Specified Condition |
| #10 (C55-45) - E01 (C55-22) | 11 to 14 V |
| #20 (C55-85) - E01 (C55-22) | 11 to 14 V |
| #30 (C55-44) - E01 (C55-22) | 11 to 14 V |
| #40 (C55-84) - E01 (C55-22) | 11 to 14 V |
| #50 (C55-43) - E01 (C55-22) | 11 to 14 V |
| #60 (C55-83) - E01 (C55-22) | 11 to 14 V |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 13.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 14.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leakage.
|
| ||||
| OK | |
| 15.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 16.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 17.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
|
| ||||
| OK | |
| 18.CHECK VALVE TIMING |
|
| ||||
| OK | ||
| ||
| 19.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks.
|
| ||||
| OK | |
| 20.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 21.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 22.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
|
| ||||
| OK | |
| 23.CHECK VALVE TIMING |
|
| ||||
| OK | |
| 24.CHECK SPARK PLUG |
![]() |
Remove the ignition coil assembly and the spark plug of the misfiring cylinder.
Measure the spark plug electrode gap.
Check the electrode for carbon deposits.
| Manufacturer | Product |
| DENSO | FK20HR11 |
Reinstall the ignition coil assembly and the spark plug.
|
| ||||
| OK | |
| 25.CHECK FOR SPARK AND IGNITION (SPARK TEST) |
Perform a spark test.
Remove the ignition coil assembly from the cylinder head.
Install the spark plug onto the ignition coil assembly.
Disconnect the 6 fuel injector assembly connectors.
Touch the spark plug to the cylinder head.
Crank the engine for less than 2 seconds and check for spark.
Reconnect the 6 fuel injector assembly connectors.
Install the ignition coil assembly.
|
| ||||
| OK | |
| 26.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 27.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C7-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C9-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C8-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C10-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C36-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
| C37-2 - Body ground | Engine switch on (IG) | 11 to 14 V |
Reconnect the fuel injector assembly connectors.
|
| ||||
| OK | |
| 28.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
![]() |
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| #10 (C58-45) - C7-1 | Below 1 Ω |
| #20 (C58-85) - C9-1 | Below 1 Ω |
| #30 (C58-44) - C8-1 | Below 1 Ω |
| #40 (C58-84) - C10-1 | Below 1 Ω |
| #50 (C58-43) - C36-1 | Below 1 Ω |
| #60 (C58-83) - C37-1 | Below 1 Ω |
| #10 (C58-45) or C7-1 - Body ground | 10 kΩ or higher |
| #20 (C58-85) or C9-1 - Body ground | 10 kΩ or higher |
| #30 (C58-44) or C8-1 - Body ground | 10 kΩ or higher |
| #40 (C58-84) or C10-1 - Body ground | 10 kΩ or higher |
| #50 (C58-43) or C36-1 - Body ground | 10 kΩ or higher |
| #60 (C58-83) or C37-1 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| #10 (C55-45) - C7-1 | Below 1 Ω |
| #20 (C55-85) - C9-1 | Below 1 Ω |
| #30 (C55-44) - C8-1 | Below 1 Ω |
| #40 (C55-84) - C10-1 | Below 1 Ω |
| #50 (C55-43) - C36-1 | Below 1 Ω |
| #60 (C55-83) - C37-1 | Below 1 Ω |
| #10 (C55-45) or C7-1 - Body ground | 10 kΩ or higher |
| #20 (C55-85) or C9-1 - Body ground | 10 kΩ or higher |
| #30 (C55-44) or C8-1 - Body ground | 10 kΩ or higher |
| #40 (C55-84) or C10-1 - Body ground | 10 kΩ or higher |
| #50 (C55-43) or C36-1 - Body ground | 10 kΩ or higher |
| #60 (C55-83) or C37-1 - Body ground | 10 kΩ or higher |
Reconnect the fuel injector assembly connectors.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 29.INSPECT ECM TERMINAL OF MISFIRING CYLINDER (#10, #20, #30, #40, #50 AND/OR #60 VOLTAGE) |
![]() |
Disconnect the ECM connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| #10 (C58-45) - E01 (C58-22) | 11 to 14 V |
| #20 (C58-85) - E01 (C58-22) | 11 to 14 V |
| #30 (C58-44) - E01 (C58-22) | 11 to 14 V |
| #40 (C58-84) - E01 (C58-22) | 11 to 14 V |
| #50 (C58-43) - E01 (C58-22) | 11 to 14 V |
| #60 (C58-83) - E01 (C58-22) | 11 to 14 V |
| Tester Connection | Specified Condition |
| #10 (C55-45) - E01 (C55-22) | 11 to 14 V |
| #20 (C55-85) - E01 (C55-22) | 11 to 14 V |
| #30 (C55-44) - E01 (C55-22) | 11 to 14 V |
| #40 (C55-84) - E01 (C55-22) | 11 to 14 V |
| #50 (C55-43) - E01 (C55-22) | 11 to 14 V |
| #60 (C55-83) - E01 (C55-22) | 11 to 14 V |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 30.CHECK FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Check the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | ||
| ||
| 31.CHANGE TO KNOWN GOOD SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed spark plug to a known good spark plug.
Perform a spark test.
Remove the ignition coil assembly from the cylinder head.
Install the spark plug onto the ignition coil assembly.
Disconnect the 6 fuel injector assembly connectors.
Touch the spark plug to the cylinder head.
Crank the engine for less than 2 seconds and check for spark.
Reconnect the 6 fuel injector assembly connectors.
Install the ignition coil assembly.
|
| ||||
| OK | ||
| ||
| 32.CHANGE TO KNOWN GOOD IGNITION COIL AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed ignition coil assembly to a known good ignition coil assembly.
Perform a spark test.
Remove the ignition coil assembly from the cylinder head.
Install the spark plug onto the ignition coil assembly.
Disconnect the 6 fuel injector assembly connectors.
Touch the spark plug to the cylinder head.
Crank the engine for less than 2 seconds and check for spark.
Reconnect the 6 fuel injector assembly connectors.
Install the ignition coil assembly.
|
| ||||
| OK | ||
| ||
| 33.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||