Home › Vehicle Exterior › WINDOW / GLASS › WINDSHIELD GLASS › 2011.10–2015.04
RM19V0EQ _59 Vehicle Exterior _014616 WINDOW / GLASS _0074212 WINDSHIELD GLASS A

WINDOW / GLASS  WINDSHIELD GLASS  REMOVAL  


PROCEDURE

Hide 1.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

Hide 2.REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

Hide 53867H 3.REMOVE FRONT FENDER TO COWL SIDE SEAL LH

Hide 53866J 4.REMOVE FRONT FENDER TO COWL SIDE SEAL RH

HINT:

Use the same procedure as for the LH side.


Hide 55781E 5.REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 87834 6.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)

Hide 87810 7.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/o EC Mirror)

Hide 87810 8.REMOVE INNER REAR VIEW MIRROR ASSEMBLY (w/ EC Mirror)

Hide 89943 9.REMOVE RAIN SENSOR COVER (w/ Rain Sensor)

Hide 62312B 10.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

Hide 62212 11.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Hide 62212 12.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

Hide 62311B 13.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 62211 14.REMOVE FRONT PILLAR GARNISH RH

HINT:

Use the same procedure as for the LH side.


Hide 63650A 15.REMOVE ROOF CONSOLE BOX ASSEMBLY (w/o Sliding Roof)

Hide 63650A 16.REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Sliding Roof)

Hide 81240 17.REMOVE NO. 1 ROOM LIGHT ASSEMBLY (w/o Sliding Roof)

Hide 81360T 18.REMOVE SPOT LIGHT ASSEMBLY (w/ Sliding Roof)

Hide 74610A 19.REMOVE ASSIST GRIP SUB-ASSEMBLY (for RH Side)

Hide 74610A 20.REMOVE ASSIST GRIP SUB-ASSEMBLY (for LH Side)

Hide 74630E 21.REMOVE REAR ASSIST GRIP ASSEMBLY LH

Hide 74620C 22.REMOVE REAR ASSIST GRIP ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 74325 23.REMOVE VISOR BRACKET COVER (for LH Side)

Hide 74320 24.REMOVE VISOR ASSEMBLY LH

Hide 74325 25.REMOVE VISOR BRACKET COVER (for RH Side)

HINT:

Use the same procedure as for the LH side.


Hide 74310 26.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.


Hide 63318C 28.REMOVE SLIDING ROOF OPENING TRIM MOULDING (w/ Sliding Roof)

Hide 29.REMOVE ROOF HEADLINING ASSEMBLY

a.

Slightly lower the front section of the roof headlining assembly so that the windshield glass can be removed.

HINT:

It is not necessary to completely remove the roof headlining assembly.



Hide 56111 30.REMOVE WINDSHIELD GLASS SUB-ASSEMBLY

a.
B279239C06
0.606,0.312 0.772,0.496 0.166,0.184 10 *1 1.004,0.633 0.802,0.431 false
*1 Protective Tape


Apply protective tape to the area around the installation position of the windshield glass on the vehicle body to prevent it from being scratched.


b.
B279244C04
1.042,0.906 0.76,0.708 false 0.781,1.771 0.458,2.104 false 1.302,2.615 1.729,2.906 false 2.156,2.615 1.729,2.896 false 2.01,3.875 1.969,4.125 false 0.958,3.542 1.469,3.385 1.469,3.385 1.719,3.313 false 2.49,3.542 1.729,3.313 false 0.271,2.063 0.469,2.25 0.198,0.188 10 false *1 0.583,0.615 0.781,0.802 0.198,0.188 10 false *2 1.677,2.917 1.875,3.104 0.198,0.188 10 false *3 1.885,4.156 2.083,4.344 0.198,0.188 10 false *4 1.646,3.146 1.844,3.333 0.198,0.188 10 false *5
*1 Wooden Block
*2 Plastic Sheet
*3 Stopper
*4 Piano Wire
*5 Windshield Glass Retainer


Pass a piano wire between the vehicle body and glass from the interior as shown in the illustration.


c.

Tie both wire ends to wooden blocks or similar objects that can serve as handles.


d.

Cut off the adhesive by pulling the piano wire around the windshield glass sub-assembly.

NOTICE:
·

When separating the windshield glass sub-assembly, be careful not to damage the paint or interior and exterior ornaments.

·

To prevent the safety pad from being scratched when removing the windshield glass, place a plastic sheet between the piano wire and safety pad.




e.
B279240C13
1.425,0.704 1.578,0.862 0.153,0.159 10 *1 1.682,0.309 1.514,0.309 1.514,0.309 1.514,0.677 false 1.682,0.55 1.514,0.55 false
*1 Matchmark


Place matchmarks on the windshield glass sub-assembly and vehicle body on the locations indicated in the illustration.

HINT:

Matchmarks are not necessary if the windshield glass sub-assembly is not going to be reused.



f.

Disconnect the windshield glass stoppers.

B279243C06
1.698,0.906 1.521,0.938 false 4.708,0.74 4.563,0.896 false 4.865,0.844 4.865,0.979 4.865,0.979 5.26,0.979 false 5.01,0.781 5.01,0.979 false 5.125,0.833 5.125,0.979 false 2.594,3.135 2.208,3.198 false 5.865,3.135 5.469,3.198 false 1.375,0.865 1.552,1.031 0.177,0.167 10 false *1 5.271,0.896 5.448,1.063 0.177,0.167 10 false *1 4.406,0.833 4.583,1 0.177,0.167 10 false *2 2.604,3.042 2.781,3.208 0.177,0.167 10 false *3 5.875,3.052 6.052,3.219 0.177,0.167 10 false *3 0.927,0.156 1.177,0.375 0.25,0.219 12 false *A 4.177,0.125 4.438,0.354 0.26,0.229 12 false *B
*A 1-piece Type *B 2-piece Type
*1 No. 1 Windshield Glass Stopper *2 No. 2 Windshield Glass Stopper
*3 Windshield Glass Retainer - -


NOTICE:
·

There are No. 1 and No. 2 stoppers on the windshield glass as shown in the illustration. Be careful not to damage the windshield glass when cutting off the adhesive.

·

To prevent the windshield glass from falling when performing this operation, be sure to hold the windshield glass using suction cups.



HINT:

Depending on the vehicle, either 1-piece or 2-piece type stoppers may be present.



g.

Using suction cups, remove the windshield glass sub-assembly.

NOTICE:
·

Be careful not to drop the windshield glass sub-assembly.

·

Leave as much adhesive on the vehicle body as possible when removing the windshield glass sub-assembly.




Hide 56117A 31.REMOVE WINDSHIELD GLASS ADHESIVE DAM

a.

When reusing the windshield glass:

i.
B279245C06
0.125,0.125 0.406,0.375 0.281,0.25 12 false *A
*A Back Side


Using a scraper, remove the windshield glass adhesive dam.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the window glass adhesive dam with a new one.





Hide 32.REMOVE WINDSHIELD OUTSIDE MOULDING

a.

When reusing the windshield glass:

i.
B280252C05
0.135,0.146 0.385,0.385 0.25,0.24 12 false *A
*A Back Side


Using a scraper, remove the windshield outside moulding.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield outside moulding with a new one.





Hide 33.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 1-piece Type)

a.

When reusing the windshield glass:

i.
B279246C09
0.094,0.115 0.458,0.427 0.365,0.313 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 1 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the 1-piece type No. 1 windshield glass stoppers with a new pair of 2-piece type No. 1 and No. 2 windshield glass stoppers.





Hide 56116C 34.REMOVE NO. 2 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.

When reusing the windshield glass:

i.
B279246C10
0.104,0.104 0.406,0.375 0.302,0.271 12 false *A
*A Back Side


Using a scraper, remove the 2 No. 2 windshield glass stoppers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the No. 2 windshield glass stoppers with new ones.





Hide 56114 35.REMOVE WINDSHIELD GLASS RETAINER

a.

When reusing the windshield glass:

i.
B280218C05
0.156,0.135 0.417,0.344 0.26,0.208 12 false *A
*A Back Side


Remove the 2 windshield glass retainers.

NOTICE:
·

Be careful not to damage the windshield glass.

·

Be sure to replace the windshield glass retainers with new ones.





Hide 56115A 36.REMOVE NO. 1 WINDSHIELD GLASS STOPPER (for 2-piece Type)

a.
B280217

Remove the 2 No. 1 windshield glass stoppers.

NOTICE:

Be sure to replace the No. 1 windshield glass stoppers with new ones.



Hide 37.CLEAN WINDSHIELD GLASS

a.

When reusing the windshield glass:

i.
B149736

Using a scraper, remove any adhesive dam and adhesive residue from the windshield glass.

NOTICE:

Be careful not to damage the windshield glass.



ii.

Clean the outer circumference of the windshield glass with a non-residue solvent.

NOTICE:
·

Do not touch the windshield glass surface after cleaning it.

·

Even if using a new windshield glass, clean the windshield glass with a non-residue solvent.





Hide 38.CLEAN VEHICLE BODY

a.
B149737C24
2.313,1.542 2.438,1.667 false 0.865,1.521 1,1.646 false 0.958,0.677 0.844,0.49 0.844,0.49 0.635,0.49 false 2.531,0.677 2.604,0.74 2.604,0.74 2.74,0.74 false 0.958,1.667 1.188,1.823 0.229,0.156 10 false *1 2.375,1.698 2.604,1.854 0.229,0.156 10 false *1 0.417,0.417 0.646,0.573 0.229,0.156 10 false *2 2.802,0.688 3.031,0.844 0.229,0.156 10 false *2
*1 Adhesive
*2 Body


Clean and shape the contact surfaces of the vehicle body.

i.

Using a knife, cut away excess adhesive on the contact surfaces of the vehicle body as shown in the illustration.

NOTICE:

Be careful not to damage the vehicle body.


HINT:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surfaces of the vehicle body with a piece of cloth saturated with cleaner.

HINT:

Even if all the adhesive has been removed, clean the vehicle body.