Home › Engine / Hybrid System › 2AR-FE ENGINE CONTROL › SFI SYSTEM › 2011.10–2013.07
RM19V0EQ _51 Engine / Hybrid System _014573 2AR-FE ENGINE CONTROL _0075838 SFI SYSTEM J

2AR-FE ENGINE CONTROL  SFI SYSTEM  Starter Signal Circuit  


DESCRIPTION

w/ smart entry and start system

While the engine is being cranked, current flows from terminal STAR of the certification ECU (smart key ECU assembly) to the park/neutral position switch assembly and to terminal STA of the ECM (STA signal).


w/o smart entry and start system (for Automatic Transaxle models)

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly to the park/neutral position switch assembly and also flows to terminal STA of the ECM (STA signal).


w/o smart entry and start system (for Manual Transaxle models)

While the engine is being cranked, current flows from terminal ST1 of the ignition switch assembly to terminal STA of the ECM (STA signal).


WIRING DIAGRAM

A266832E05
5.708,3.688 6.083,3.865 0.375,0.177 10 false STA 5.427,3.615 5.615,3.771 0.188,0.156 10 false 22 5.344,3.781 5.615,3.938 0.271,0.156 10 false A25 5.74,0.698 6.115,0.875 0.375,0.177 10 false NEO 5.427,0.604 5.615,0.76 0.188,0.156 10 false 45 5.354,0.781 5.625,0.938 0.271,0.156 10 false A25 5.74,1.448 6.115,1.625 0.375,0.177 10 false NSW 5.427,1.427 5.615,1.583 0.188,0.156 10 false 63 5.344,1.594 5.615,1.75 0.271,0.156 10 false E26 6.135,4.948 6.479,5.115 0.344,0.167 10 false ECM 3.563,2.271 3.667,2.427 0.104,0.156 10 false 9 3.719,2.271 3.823,2.427 0.104,0.156 10 false L 4.375,2.271 4.49,2.427 0.115,0.156 10 false B 4.583,2.26 4.708,2.417 0.125,0.156 10 false 4 3.333,2.656 3.615,2.813 0.281,0.156 10 false E4 3.333,2.823 5.125,3.271 1.792,0.448 10 false Park/Neutral Position Switch Assembly 0.094,0.083 2.583,0.271 2.49,0.188 12 false w/ Smart Entry and Start System: 0.615,3.823 1.146,3.979 0.531,0.156 10 false ST/AM2 0.615,4.917 1.229,5.073 0.615,0.156 10 false FL MAIN 1.5,0.781 1.979,0.958 0.479,0.177 10 false NE 1.802,0.688 2.063,0.844 0.26,0.156 10 false 16 1.323,1.604 1.708,1.76 0.385,0.156 10 false STAR 1.802,1.51 1.927,1.667 0.125,0.156 10 false 5 1.417,2.125 1.708,2.281 0.292,0.156 10 false STA 1.802,2.031 1.927,2.188 0.125,0.156 10 false 7 0.198,2.542 0.51,2.708 0.313,0.167 10 false A43 0.198,2.708 2.031,3.125 1.833,0.417 10 false Certification ECU (Smart Key ECU Assembly) 3.292,4.615 3.521,4.771 0.229,0.156 10 false ST 3.021,4.146 3.146,4.302 0.125,0.156 10 false 2 3.021,5.052 3.146,5.208 0.125,0.156 10 false 1 2.573,4.156 2.667,4.313 0.094,0.156 10 false 5 2.573,5.042 2.667,5.198 0.094,0.156 10 false 3 1.792,5.51 2,5.667 0.208,0.156 10 false E9 1.771,5.354 1.865,5.51 0.094,0.156 10 false 1 1.135,5.75 1.26,5.917 0.125,0.167 10 false 1 1.083,5.927 1.302,6.083 0.219,0.156 10 false F2 1.563,6.74 2.188,7.208 0.625,0.469 10 false Starter Assembly 0.76,6.833 1.24,7 0.479,0.167 10 false Battery

A266092E01
5.694,1.119 6.178,1.294 0.484,0.175 10 NSW*1 5.719,3.463 6.097,3.638 0.378,0.175 10 STA 5.404,1.107 5.595,1.263 0.191,0.156 10 63 5.355,1.276 5.63,1.432 0.274,0.156 10 E26 5.401,3.375 5.592,3.532 0.191,0.156 10 22 5.354,3.55 5.626,3.707 0.272,0.156 10 A25 6.116,4.718 6.459,4.888 0.344,0.17 10 ECM 3.385,2.416 3.666,2.572 0.281,0.156 10 E4 3.385,2.584 5.167,2.916 1.782,0.332 10 Park/Neutral Position Switch Assembly 0.075,0.058 2.664,0.242 2.589,0.184 12 w/o Smart Entry and Start System: 1.354,1.171 1.478,1.323 0.124,0.152 10 4 1.532,1.171 1.835,1.323 0.304,0.152 10 AM1 1.09,2.866 1.394,3.018 0.304,0.152 10 AM1 1.102,3.686 1.406,3.837 0.304,0.152 10 ALT 2.118,1.171 2.401,1.323 0.282,0.152 10 ST1 2.461,1.171 2.585,1.323 0.124,0.152 10 3 1.354,1.605 1.478,1.757 0.124,0.152 10 5 1.532,1.605 1.835,1.757 0.304,0.152 10 AM2 0.565,2.782 0.868,3.105 0.304,0.323 10 ST/AM2 2.118,1.605 2.401,1.757 0.282,0.152 10 ST2 2.461,1.605 2.585,1.757 0.124,0.152 10 7 1.541,2.047 1.854,2.217 0.313,0.17 10 I36 1.541,2.208 2.524,3.506 0.983,1.299 10 Ignition or Starter Switch Assembly 3.264,4.378 3.49,4.535 0.226,0.156 10 ST 3.002,3.917 3.124,4.073 0.122,0.156 10 2 3.002,4.828 3.124,4.984 0.122,0.156 10 1 2.568,3.917 2.689,4.073 0.122,0.156 10 5 2.568,4.828 2.689,4.984 0.122,0.156 10 3 1.783,5.294 1.995,5.45 0.212,0.156 10 E9 1.753,5.096 1.878,5.266 0.125,0.17 10 1 1.116,5.514 1.241,5.684 0.125,0.17 10 1 1.072,5.703 1.293,5.862 0.221,0.16 10 F2 1.478,6.488 2.159,6.846 0.681,0.358 10 Starter Assembly 0.725,6.602 1.208,6.772 0.483,0.17 10 Battery 4.562,2.04 4.686,2.192 0.124,0.152 10 4 4.408,2.04 4.532,2.192 0.124,0.152 10 B 3.553,2.04 3.652,2.192 0.098,0.152 10 9 3.707,2.04 3.806,2.192 0.098,0.152 10 L 5.119,1.186 5.27,1.342 0.151,0.156 10 *1 4.138,1.186 4.289,1.342 0.151,0.156 10 *1 3.083,1.691 3.234,1.848 0.151,0.156 10 *2 3.312,2.04 3.463,2.196 0.151,0.156 10 *1 5.075,2.06 5.226,2.216 0.151,0.156 10 *1 4.094,6.963 6.134,7.12 2.04,0.156 10 *2: for Manual Transaxle models 4.094,6.543 6.273,6.699 2.179,0.156 10 *1: for Automatic Transaxle models 0.598,4.919 1.165,5.07 0.567,0.152 10 FL MAIN

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After turning ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK WHETHER ENGINE CAN BE CRANKED
a.

Check if the engine can be cranked.


Result:
Result Proceed to
Engine cannot be cranked A
Engine can be cranked B



A

2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)

B

21.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
2.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON Close (OFF)
START Open (ON)



Result:
Result Proceed to
OK A
NG (for Automatic Transaxle models) B
NG (for Manual Transaxle models) C



A

3.INSPECT RELAY (ST RELAY)

B

13.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

19.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
3.INSPECT RELAY (ST RELAY)

Result:
Proceed to
OK
NG



OK

4.INSPECT STARTER ASSEMBLY

NG

REPLACE RELAY (ST RELAY)

4.INSPECT STARTER ASSEMBLY
a.

Inspect the starter assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>STARTER>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)

NG

REPLACE STARTER ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (ST RELAY - STARTER ASSEMBLY)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the starter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 3 - E9-1 Always Below 1 Ω
ST relay terminal 3 or E9-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (BATTERY - STARTER ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the cable from the positive (+) battery terminal.


c.

Disconnect the starter assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) battery terminal - F2-1 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 1 - Body ground Always Below 1 Ω



Result:
Result Proceed to
OK (w/o smart entry and start system)
(for Automatic Transaxle models)
A
OK (w/o smart entry and start system)
(for Manual Transaxle models)
B
OK (w/ smart entry and start system) C
NG D



A

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

B

9.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)

C

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)

D

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-9 (L) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I36-3 (ST1) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I36-7 (ST2) - ST relay terminal 5 Always Below 1 Ω
I36-7 (ST2) or ST relay terminal 5 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-9 (L) - ST relay terminal 2 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - ST RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Inspect the park/neutral position switch assembly.

Click hereDrivetrain>U760E AUTOMATIC TRANSMISSION / TRANSAXLE>PARK / NEUTRAL POSITION SWITCH>INSPECTION


Result:
Result Proceed to
OK (w/o smart entry and start system) A
OK (w/ smart entry and start system) B
NG C



A

14.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY

B

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)

C

14.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

15.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I36-3 (ST1) - E4-4 (B) Always Below 1 Ω
I36-3 (ST1) - E26-63 (NSW) Always Below 1 Ω
I36-3 (ST1), E4-4 (B) or E26-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY AND ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY AND ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E4-9 (L) - A25-22 (STA) Always Below 1 Ω
E4-9 (L), ST relay terminal 2 or A25-22 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - PARK/NEUTRAL POSITION SWITCH ASSEMBLY AND ECM)
a.

Disconnect the park/neutral position switch assembly connector.


b.

Disconnect the certification ECU (smart key ECU assembly) connector.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A43-5 (STAR) - E4-4 (B) Always Below 1 Ω
A43-5 (STAR) - E26-63 (NSW) Always Below 1 Ω
A43-5 (STAR) or E4-4 (B) or E26-63 (NSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY, ECM AND CERTIFICATION ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - ST RELAY, ECM AND CERTIFICATION ECU)
a.

Remove the ST relay from the engine room relay block and junction block assembly.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Disconnect the ECM connector.


d.

Disconnect the certification ECU (smart key ECU assembly) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
ST relay terminal 2 - E4-9 (L) Always Below 1 Ω
ST relay terminal 2 or E4-9 (L) or A25-22 (STA) or A43-7 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
a.

Inspect the ignition or starter switch assembly.

Click hereEngine / Hybrid System>2AR-FE STARTING>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

20.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY AND ECM)

NG

REPLACE IGNITION OR STARTER SWITCH ASSEMBLY

20.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY AND ECM)
a.

Disconnect the ignition or starter switch assembly connector.


b.

Remove the ST relay from the engine room relay block and junction block assembly.


c.

Disconnect the ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I36-3 (ST1) - A25-22 (STA) Always Below 1 Ω
I36-3 (ST1), ST relay terminal 2 or A25-22 (STA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - IGNITION OR STARTER SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

21.READ VALUE USING INTELLIGENT TESTER (STARTER SIGNAL)
a.

Connect the intelligent tester to DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Signal
50003 234 118

e.

Check the value displayed on the tester when the ignition switch is turned to the ON and START positions.

OK:
Ignition Switch Position Starter Signal
ON Close (OFF)
START Open (ON)



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ST RELAY - ECM)