Home › Suspension › FRONT SUSPENSION › FRONT LOWER SUSPENSION ARM(for Automatic Transaxle) › from 2015.04
RM19V0EQ _53 Suspension _014588 FRONT SUSPENSION _0074020 FRONT LOWER SUSPENSION ARM(for Automatic Transaxle) A

FRONT SUSPENSION  FRONT LOWER SUSPENSION ARM(for Automatic Transaxle)  INSTALLATION  


PROCEDURE

Hide 48069 1.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH (for LH Side)

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly LH.


b.
C167143E01
0.656,0.357 0.795,0.515 0.139,0.158 10 1 1.147,0.24 1.286,0.398 0.139,0.158 10 2 2.467,0.926 2.613,1.077 0.146,0.150 10 3

Install the front lower No. 1 suspension arm sub-assembly LH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt 1, 2 : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt 3 : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

While keeping the nut from rotating, tighten the bolt.



c.
C238972C04
0.323,2.877 3.177,4.29 2.853,1.413 1.786,2.877 1.786,4.29 false 1.26,3.745 1.429,3.915 0.169,0.171 10 *a 2.703,3.745 2.872,3.915 0.169,0.171 10 *b 0.418,2.961 0.611,3.118 0.193,0.157 10 *A 1.896,2.961 2.078,3.114 0.181,0.153 10 *B
*A Type A Nut
*B Type B Nut
*a 20 mm (0.787 in.)
*b 22 mm (0.866 in.)
V100135

Bolt
V100136

Nut


Install the front lower No. 1 suspension arm sub-assembly LH to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
Type A Nut and Bolt : 75 N*m (765 kgf*cm, 55 ft.*lbf)
Type B Nut and Bolt : 92 N*m (938 kgf*cm, 68 ft.*lbf)

NOTICE:
·

The tightening torque for the bolt differs depending on the type of nut.

·

Make sure to tighten the bolt to the same torque as the nuts.




Hide 12372A 2.INSTALL ENGINE MOUNTING INSULATOR LH (for LH Side)

a.
C224297C01
1.781,0.823 2.26,0.823 false 2.281,0.75 2.604,1.021 0.323,0.271 10 false *a
*a Pin


Set the engine mounting insulator LH on the front frame assembly.


b.

Slowly lower the engine assembly with transaxle using a jack and a wooden block.

NOTICE:
·

Match the position of the pin (stopper).

·

Do not position the wooden block on the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.




c.
C246183C01
1.396,1.208 0.844,1.625 0.844,1.625 0.844,2.292 true 2.313,0.823 2.531,1.031 0.219,0.208 10 true *a 0.719,2.313 1.073,2.542 0.354,0.229 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the nut to the engine mounting insulator LH.

SST
09961-00950  

Torque:
Specified tightening torque : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

This torque value is effective when SST is parallel to the torque wrench.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 380 mm (1.25 ft.)):

68 N*m (695 kgf*cm, 50 ft.*lbf)




d.
C239289

Install the engine mounting insulator LH with the 3 nuts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


e.

Install the 2 hole plugs.


Hide 48068 3.INSTALL FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH (for RH Side)

a.

Install the front lower arm bushing stopper to the front lower No. 1 suspension arm sub-assembly RH.


b.
C239314E01
2.639,0.27 2.746,0.422 0.106,0.152 10 1 2.15,0.233 2.257,0.385 0.106,0.152 10 2 0.853,0.937 0.959,1.089 0.106,0.152 10 3

Install the front lower No. 1 suspension arm sub-assembly RH to the front frame assembly with the 3 bolts and nut in the order shown in the illustration.

Torque:
Bolt 1, 2 : 200 N*m (2039 kgf*cm, 148 ft.*lbf)
Bolt 3 : 135 N*m (1377 kgf*cm, 100 ft.*lbf)

NOTICE:

While keeping the nut from rotating, tighten the bolt.



c.
C239315C02
0.315,2.887 3.168,4.3 2.853,1.413 1.778,2.887 1.778,4.3 false 1.268,3.755 1.435,3.91 0.166,0.155 10 *a 2.712,3.755 2.879,3.91 0.166,0.155 10 *b 0.41,2.972 0.602,3.128 0.193,0.157 10 *A 1.888,2.972 2.069,3.125 0.181,0.153 10 *B
*A Type A Nut
*B Type B Nut
*a 20 mm (0.787 in.)
*b 22 mm (0.866 in.)
V100135

Bolt
V100136

Nut


Install the front lower No. 1 suspension arm sub-assembly RH to the front lower ball joint assembly with the bolt and 2 nuts.

Torque:
Type A Nut and Bolt : 75 N*m (765 kgf*cm, 55 ft.*lbf)
Type B Nut and Bolt : 92 N*m (938 kgf*cm, 68 ft.*lbf)

NOTICE:
·

The tightening torque for the bolt differs depending on the type of nut.

·

Make sure to tighten the bolt to the same torque as the nuts.




Hide 12362A 4.INSTALL ENGINE MOUNTING INSULATOR RH (for RH Side)

a.
C247223C01
2.469,0.417 2.75,0.802 2.75,0.802 2.448,1.26 false 2.781,0.729 3.063,1.021 0.281,0.292 10 false *a
*a Cutout


Set the engine mounting insulator RH on the front frame assembly.


b.

Slowly lower the engine assembly with transaxle using a jack and a wooden block.

NOTICE:
·

Match the position of the cutout (stopper).

·

Do not position the wooden block on the oil pan.

·

Do not damage the components surrounding the engine assembly with transaxle.

·

Ensure that the jack and wooden block are stable.




c.
C246184C01
2.104,1.281 2.438,1.729 2.438,1.729 2.438,2.406 true 0.938,0.927 1.146,1.115 0.208,0.188 10 true *a 2.313,2.417 2.719,2.688 0.406,0.271 10 false SST
*a Torque Wrench Fulcrum Length


Using SST, install the nut to the engine mounting insulator RH.

SST
09961-00950  

Torque:
Specified tightening torque : 95 N*m (969 kgf*cm, 70 ft.*lbf)

NOTICE:

This torque value is effective when SST is parallel to the torque wrench.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using SST (fulcrum length of 150 mm (5.91 in.)) + torque wrench (fulcrum length of 380 mm (1.25 ft.)):

68 N*m (695 kgf*cm, 50 ft.*lbf)




d.
C247221

Install the engine mounting insulator RH with the 3 nuts.

Torque:
87 N*m (887 kgf*cm, 64 ft.*lbf)


e.

Install the 2 hole plugs.


Hide 12309 5.INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY (for RH Side)

a.
C239312

Temporarily install the engine moving control rod sub-assembly with the 4 bolts.


b.

Fully tighten the engine moving control rod sub-assembly with the 4 bolts.

Torque:
38 N*m (387 kgf*cm, 28 ft.*lbf)


Hide 12327A 6.INSTALL NO. 2 ENGINE MOUNTING STAY RH (for RH Side)

Hide 82284 7.INSTALL EARTH WIRE (for RH Side)

Hide 12361A 8.INSTALL FRONT ENGINE MOUNTING INSULATOR

a.

Install the front engine mounting insulator to the front frame assembly with the 3 nuts.

Torque:
52 N*m (530 kgf*cm, 38 ft.*lbf)


Hide 53737B 9.INSTALL FRONT FENDER APRON SEAL LH (for LH Side)

Hide 53736 10.INSTALL FRONT FENDER APRON SEAL RH (for RH Side)

Hide 51442C 11.INSTALL ENGINE UNDER COVER LH

Hide 51441C 12.INSTALL ENGINE UNDER COVER RH

Hide 53852K 13.INSTALL FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)

Hide 53851Z 14.INSTALL FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)

Hide 15.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 16.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 55702A 18.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for LHD)

Hide 55702A 19.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY (for RHD)

Hide 20.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for LHD)

Hide 21.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY (for RHD)

Hide 22.INSTALL FRONT WHEELS

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 23.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 24.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT