1. PRECAUTION
Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
67914
3.REMOVE FRONT DOOR SCUFF PLATE LH
62112A
4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH
62312B
5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH
Disconnect the front door opening trim weatherstrip LH.
55318C
6.REMOVE INSTRUMENT SIDE PANEL LH
Using a moulding remover, disengage the 4 claws as shown in the illustration.
Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.
55474C
7.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD)
Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.
55431B
8.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)
Disengage the 4 clips to remove the upper instrument panel finish panel as shown in the illustration.
w/ Smart Entry and Start System
Disconnect the connector.
55650
9.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Disengage the 2 clips as shown in the illustration.
Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.
55410C
10.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.
Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.
Disengage the 5 claws, 5 clips and 2 guides.
Disconnect each connector.
Remove the instrument cluster finish panel assembly as shown in the illustration.
83100
11.REMOVE COMBINATION METER ASSEMBLY
53922B
12.REMOVE FRONT PANEL GARNISH LH
Disengage the claw, 5 clips and 6 guides to remove the front panel garnish LH.
53601
13.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY
Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.
14.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)
Remove the 2 bolts <B>.
Disengage the 5 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.
15.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for RHD)
Remove the 2 bolts <B>.
Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.
Disconnect each connector.
53921B
16.REMOVE FRONT PANEL GARNISH RH
Disengage the claw, 5 clips and 6 guides to remove the front panel garnish RH.
33504F
17.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY
Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.
58805C
18.REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY
Move the shift lever to N.
Disengage the 4 clips.
Disconnect each connector and remove the rear console upper panel sub-assembly.
58801E
19.REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY
58864B
20.REMOVE NO. 4 CONSOLE BOX DUCT
58815A
21.REMOVE CONSOLE BOX CARPET
22.REMOVE REAR CONSOLE BOX ASSEMBLY
23.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY
Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.
Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.
Disengage the 3 claws and 2 clips as shown in the illustration.
Disengage the clamp.
Disconnect the connector to remove the center instrument cluster finish panel assembly.
55660
24.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY
Pull the No. 2 instrument panel register assembly as shown in the illustration to disengage the 6 clips and remove the No. 2 instrument panel register assembly.
58916
25.REMOVE BOX BOTTOM MAT
Remove the box bottom mat.
58804A
26.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
Remove the 2 screws <C> or <D>.
Disengage the 4 clips and guide as shown in the illustration.
Disconnect each connector to remove the upper console panel sub-assembly.
27.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver)
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Remove the 4 bolts.
Pull the center instrument cluster finish panel with air conditioning control assembly toward the rear of the vehicle and disengage the 10 clips.
Disconnect the connector and remove the center instrument cluster finish panel with air conditioning control assembly.
28.REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)
29.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)
55510F
30.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY
Disengage the 8 clips as shown in the illustration.
Disconnect the connector to remove the No. 1 speaker opening cover assembly.
86160J
31.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)
67911B
32.REMOVE FRONT DOOR SCUFF PLATE RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62111A
33.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62311B
34.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH
Disconnect the front door opening trim weatherstrip RH.
55317A
35.REMOVE INSTRUMENT SIDE PANEL RH
Using a moulding remover, disengage the 4 claws as shown in the illustration.
Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.
55607
36.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY
Disengage the 4 claws.
Disengage the 2 guides.
Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.
55303B
37.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
Remove the bolt <B> and screw <C> or <D>.
Open the lower instrument panel door.
Remove the 3 screws <C> or <D>.
Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.
55475A
38.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
Disengage the 5 clips to remove the No. 2 instrument cluster finish panel garnish as shown in the illustration.
55670
39.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Disengage the 2 clips as shown in the illustration.
Using a moulding remover, disengage the 2 clips to remove the No. 3 instrument panel register assembly.
62212
40.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)
62212
41.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)
55408F
42.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 clips and 3 claws.
Disengage the 2 guides to remove the No. 1 instrument panel speaker panel sub-assembly.
86160P
43.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)
62211
44.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
62211
45.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)
Use the same procedure as for the LH side.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL
55409F
46.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY
| *1 | Protective Tape |
Apply protective tape to the area shown in the illustration.
Using a moulding remover, disengage the 2 clips and 3 claws.
Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.
86160P
47.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)
Use the same procedure as for the LH side.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
55480D
48.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
Disengage the 4 clips to remove the lower instrument panel finish panel assembly.
for LHD with Smart Entry and Start System:
Disconnect the connector.
58817A
49.REMOVE FRONT NO. 2 CONSOLE BOX INSERT
Remove the 2 screws <C> or <D>.
Disengage the clip and 3 guides and remove the front No. 2 console box insert as shown in the illustration.
for LHD with Automatic Air Conditioning System:
Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.
58816B
50.REMOVE CONSOLE BOX INSERT
Remove the 2 screws <C> or <D>.
Disengage the clip and 3 guides and remove the console box insert as shown in the illustration.
for RHD with Automatic Air Conditioning System:
Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.
55011A
51.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY
Disengage the 10 clips to remove the No. 1 instrument panel garnish sub-assembly as shown in the illustration.
82142A
52.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE
53.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
Disconnect each connector.
Disengage each clamp.
Remove the 2 passenger airbag bolts <A>.
| *1 | Passenger Airbag Bolt <A> | *2 | Bolt <B> |
| *3 | Nut <F> or <G> | *4 | Clip |
Remove the 3 bolts <B> and nut <F> or <G>.
Remove the 2 clips.
Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.
Do not damage the instrument panel safety pad assembly.
Do not allow the wire harnesses to interfere with the surrounding parts.