Home › Vehicle Interior › INTERIOR PANELS / TRIM › INSTRUMENT PANEL SAFETY PAD › 2014.05–2015.04
RM19V0EQ _58 Vehicle Interior _014615 INTERIOR PANELS / TRIM _0074204 INSTRUMENT PANEL SAFETY PAD A

INTERIOR PANELS / TRIM  INSTRUMENT PANEL SAFETY PAD  REMOVAL  


PROCEDURE

Hide 1. PRECAUTION

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 67914 3.REMOVE FRONT DOOR SCUFF PLATE LH

Hide 62112A 4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

Hide 62312B 5.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP LH

a.
B292349

Disconnect the front door opening trim weatherstrip LH.


Hide 55318C 6.REMOVE INSTRUMENT SIDE PANEL LH

a.
B292350

Using a moulding remover, disengage the 4 claws as shown in the illustration.


b.
B292353

Disengage the 3 guides and remove the instrument side panel LH as shown in the illustration.


Hide 55474C 7.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH (for LHD)

a.
B292354

Disengage the 3 clips to remove the No. 1 instrument cluster finish panel garnish as shown in the illustration.


Hide 55431B 8.REMOVE UPPER INSTRUMENT PANEL FINISH PANEL (for RHD)

a.
B292351

Disengage the 4 clips to remove the upper instrument panel finish panel as shown in the illustration.


b.

w/ Smart Entry and Start System

i.

Disconnect the connector.



Hide 55650 9.REMOVE NO. 1 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B292355C01
2.24,1.542 2.615,1.198 false 2.635,1.031 3.073,1.333 0.438,0.302 10 false *1
*1 Protective Tape


Apply protective tape to the area shown in the illustration.


b.
B292356

Disengage the 2 clips as shown in the illustration.


c.
B292357

Using a moulding remover, disengage the 2 clips to remove the No. 1 instrument panel register assembly.


Hide 55410C 10.REMOVE INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.

Operate the tilt and telescopic lever to fully extend and lower the steering column assembly.


b.
B279860

Using a moulding remover, disengage the 2 claws, 4 clips and 2 guides.


c.
B292358

Disengage the 5 claws, 5 clips and 2 guides.


d.

Disconnect each connector.


e.
B292359

Remove the instrument cluster finish panel assembly as shown in the illustration.


Hide 83100 11.REMOVE COMBINATION METER ASSEMBLY

Hide 53922B 12.REMOVE FRONT PANEL GARNISH LH

a.
B279866

Disengage the 3 claws, 2 clips and 8 guides to remove the front panel garnish LH.


Hide 53601 13.DISCONNECT HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

a.
B279865

Disengage the claw and 2 guides to disconnect the hood lock control lever sub-assembly.


Hide 14.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for LHD)

a.
B292360

Remove the 2 bolts <B>.


b.
B292362

Disengage the 5 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.


Hide 15.REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL ASSEMBLY (for RHD)

a.
B293624

Remove the 2 bolts <B>.


b.
B292361

Disengage the 4 claws, 9 clips and 3 guides to remove the lower No. 1 instrument panel finish panel assembly.


Hide 53921B 16.REMOVE FRONT PANEL GARNISH RH

a.
B279869

Disengage the 3 claws, 2 clips and 8 guides to remove the front panel garnish RH.


Hide 33504F 17.REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

a.
B279870

Turn the shift lever knob sub-assembly counterclockwise and remove the shift lever knob sub-assembly.


Hide 58805C 18.REMOVE REAR CONSOLE UPPER PANEL SUB-ASSEMBLY

a.

Move the shift lever to N.


b.
B279872

Disengage the 4 clips.


c.

Disconnect each connector and remove the rear console upper panel sub-assembly.


Hide 58801E 19.REMOVE UPPER CONSOLE BOX SUB-ASSEMBLY

Hide 58864B 20.REMOVE NO. 4 CONSOLE BOX DUCT

Hide 58815A 21.REMOVE CONSOLE BOX CARPET

Hide 22.REMOVE REAR CONSOLE BOX ASSEMBLY

Hide 23.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

a.
B279875

Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.


b.
B279876

Using a moulding remover, disengage the 2 claws and 2 clips as shown in the illustration.


c.
B279877

Disengage the 3 claws and 2 clips as shown in the illustration.


d.
B279874

Disengage the clamp.


e.

Disconnect the connector to remove the center instrument cluster finish panel assembly.


Hide 55660 24.REMOVE NO. 2 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B279890

Pull the No. 2 instrument panel register assembly in the direction indicated by the arrow to disengage the 6 clips to remove the No. 2 instrument panel register assembly.


Hide 58916 25.REMOVE BOX BOTTOM MAT

a.
B279879

Remove the box bottom mat.


Hide 58804A 26.REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

a.
B279880

Remove the 2 screws <C> or <D>.


b.
B279881

Disengage the 4 clips and guide as shown in the illustration.


c.

Disconnect each connector to remove the upper console panel sub-assembly.


Hide 27.REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Radio Receiver)

a.
B293635C01
2.802,0.938 2.49,0.854 false 2.854,0.854 3.26,1.115 0.406,0.26 10 false *1
*1 Protective Tape


Apply protective tape to the areas shown in the illustration.


b.
B293620

Remove the 4 bolts.


c.
B293621

Pull the center instrument cluster finish panel with air conditioning control assembly toward the rear of the vehicle and disengage the 10 clips.


d.

Disconnect the connector and remove the center instrument cluster finish panel with air conditioning control assembly.


Hide 28.REMOVE RADIO RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/o Navigation System)

Hide 29.REMOVE NAVIGATION RECEIVER ASSEMBLY WITH AIR CONDITIONING CONTROL ASSEMBLY (w/ Navigation System)

Hide 55510F 30.REMOVE NO. 1 SPEAKER OPENING COVER ASSEMBLY

a.
B279889

Disengage the 8 clips as shown in the illustration.


b.

Disconnect the connector to remove the No. 1 speaker opening cover assembly.


Hide 86160J 31.REMOVE FRONT NO. 3 SPEAKER ASSEMBLY (for 10 Speakers)

Hide 67911B 32.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62111A 33.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62311B 34.DISCONNECT FRONT DOOR OPENING TRIM WEATHERSTRIP RH

a.
B279882

Disconnect the front door opening trim weatherstrip RH.


Hide 55317A 35.REMOVE INSTRUMENT SIDE PANEL RH

a.
B279883

Using a moulding remover, disengage the 4 claws as shown in the illustration.


b.
B279885

Disengage the 3 guides to remove the instrument side panel RH as shown in the illustration.


Hide 55607 36.REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

a.
B279888

Disengage the 4 claws.


b.

Disengage the 2 guides.


c.

Disconnect the connector and remove the No. 2 instrument panel under cover sub-assembly.


Hide 55303B 37.REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

a.
B281767

Remove the bolt <B> and screw <C> or <D>.


b.

Open the lower instrument panel door.


c.
B281768

Remove the 3 screws <C> or <D>.


d.
B281769

Disengage the 2 clips, 4 guides and remove the lower instrument panel sub-assembly as shown in the illustration.


Hide 55475A 38.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
B279887

Disengage the 5 clips to remove the No. 2 instrument cluster finish panel garnish as shown in the illustration.


Hide 55670 39.REMOVE NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY

a.
B279892C02
1.156,1.49 0.792,1.188 false 0.625,1.052 1.01,1.302 0.385,0.25 10 false *1
*1 Protective Tape


Apply protective tape to the area shown in the illustration.


b.
B279893

Disengage the 2 clips as shown in the illustration.


c.
B279894

Using a moulding remover, disengage the 2 clips to remove the No. 3 instrument panel register assembly.


Hide 62212 40.REMOVE FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

Hide 62212 41.REMOVE FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

Hide 55408F 42.REMOVE NO. 1 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B280301C02
2.406,1.677 2.292,1.313 false 2.365,1.708 2.906,2.021 0.542,0.313 10 false *1
*1 Protective Tape


Apply protective tape to the area shown in the illustration.


b.
B280302

Using a moulding remover, disengage the 2 clips and 3 claws.


c.

Disengage the 2 guides to remove the No.1 instrument panel speaker panel sub-assembly.


Hide 86160P 43.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)

Hide 62211 44.REMOVE FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 62211 45.REMOVE FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

HINT:

Use the same procedure as for the LH side.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>ROOF HEADLINING>REMOVAL


Hide 55409F 46.REMOVE NO. 2 INSTRUMENT PANEL SPEAKER PANEL SUB-ASSEMBLY

a.
B279896C05
1.302,1.333 1.208,1.552 false 1.094,1.573 1.521,1.844 0.427,0.271 10 false *1
*1 Protective Tape


Apply protective tape to the area shown in the illustration.


b.
B279897

Using a moulding remover, disengage the 2 clips and 3 claws.


c.

Disengage the 2 guides to remove the No. 2 instrument panel speaker panel sub-assembly.


Hide 86160P 47.REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:

Use the same procedure as for the LH side.

Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL


Hide 55480D 48.REMOVE LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

a.
B279899

Disengage the 4 clips to remove the lower instrument panel finish panel assembly.


b.

for LHD with Smart Entry and Start System:

i.

Disconnect the connector.



Hide 58817A 49.REMOVE FRONT NO. 2 CONSOLE BOX INSERT

a.
B280291

Remove the 2 screws <C> or <D>.


b.
B280292

Disengage the clip and 3 guides and remove the front No. 2 console box insert as shown in the illustration.


c.

for LHD with Automatic Air Conditioning System:

i.
B292376

Disengage the 2 claws to disconnect the room temperature sensor from the front No. 2 console box insert.



Hide 58816B 50.REMOVE CONSOLE BOX INSERT

a.
B279900

Remove the 2 screws <C> or <D>.


b.
B279901

Disengage the clip and 3 guides and remove the console box insert as shown in the illustration.


c.

for RHD with Automatic Air Conditioning System:

i.
B281942

Disengage the 2 claws to disconnect the room temperature sensor from the console box insert.



Hide 55011A 51.REMOVE NO. 1 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY

a.

Disengage the 10 clips to remove the No.1 instrument panel garnish sub-assembly as shown in the illustration.

B280294


Hide 82142A 52.DISCONNECT NO. 2 INSTRUMENT PANEL WIRE

Hide 53.REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY

a.

Disconnect each connector.

B280296


b.

Disengage each clamp.


c.

Remove the 2 passenger airbag bolts <A>.

B280297C03
6.438,2.656 5.375,3.469 false 6.031,2.115 6.208,2.115 false 1.958,3.74 2.115,3.74 false 4.646,0.531 4.448,0.531 false 1.25,0.719 0.917,0.719 false 3.833,0.979 3.01,2.146 false 4.927,3.708 4.25,3.917 false 4.479,3.24 4.531,3.052 false 2.146,3.667 2.552,3.938 0.406,0.271 10 false *2 4.083,3.844 4.417,4.125 0.333,0.281 10 false *1 6.448,2.563 6.844,2.802 0.396,0.24 10 false *1 6.24,2 6.563,2.208 0.323,0.208 10 false *2 1.302,0.625 1.677,0.865 0.375,0.24 10 false *4 4.302,0.448 4.583,0.635 0.281,0.188 10 false *4 3.865,0.875 4.198,1.083 0.333,0.208 10 false *3 4.375,3.26 4.781,3.531 0.406,0.271 10 false *2
*1 Passenger Airbag Bolt <A> *2 Bolt <B>
*3 Nut <F> or <G> *4 Clip



d.

Remove the 3 bolts <B> and nut <F> or <G>.


e.

Remove the 2 clips.


f.

Disengage the 5 guides and remove the instrument panel safety pad assembly as shown in the illustration.

B280298

NOTICE:
·

Do not damage the instrument panel safety pad assembly.

·

Do not allow the wire harnesses to interfere with the surrounding parts.