Use the same procedure for the RH side and LH side.
The procedure listed below is for the LH side.
43502E
1.INSTALL FRONT AXLE HUB BEARING
Using SST and a press, install a new front axle hub bearing to the steering knuckle.
47782
2.INSTALL FRONT DISC BRAKE DUST COVER
Install the front disc brake dust cover to the steering knuckle with the 4 bolts.
43502C
3.INSTALL FRONT AXLE HUB SUB-ASSEMBLY
Using SST and a press, install the front axle hub sub-assembly to the steering knuckle.
43502G
4.INSTALL FRONT AXLE HUB HOLE SNAP RING
Using snap ring pliers, install a new front axle hub hole snap ring.
43246B
5.INSTALL FRONT NO. 1 WHEEL BEARING DUST DEFLECTOR
Set a new front No. 1 wheel bearing dust deflector to the steering knuckle while aligning the cutout for the speed sensor in the front No. 1 wheel bearing dust deflector with the hole of the steering knuckle.
Using SST and a hammer, install the front No. 1 wheel bearing dust deflector.
6.INSTALL FRONT AXLE ASSEMBLY
Install the front axle assembly to the front shock absorber assembly with the 2 bolts and 2 nuts.
When installing the nuts, keep the bolts from rotating.
43420
7.INSTALL FRONT DRIVE SHAFT ASSEMBLY
| *a | Matchmark |
Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
Be careful not to damage the drive shaft boot or speed sensor rotor.
48069
8.CONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY
| *A | Type A Nut |
| *B | Type B Nut |
| *a | 20 mm (0.787 in.) |
| *b | 22 mm (0.866 in.) |
|
Bolt |
|
Nut |
Connect the front lower No. 1 suspension arm sub-assembly to the front lower ball joint assembly with the bolt and 2 nuts.
The tightening torque for the bolt differs depending on the type of nut.
Make sure to tighten the bolt to the same torque as the nuts.
45470
9.CONNECT TIE ROD ASSEMBLY
43512
10.INSTALL FRONT DISC
11.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
43502H
12.INSTALL FRONT AXLE SHAFT NUT
Clean the threaded parts on the front drive shaft assembly and a new front axle shaft nut using a non-residue solvent.
Be sure to perform this work even, when using a new front drive shaft assembly.
Keep the threaded parts free of oil and foreign matter.
Using a socket wrench (30 mm), install the front axle shaft nut.
Stake the nut after inspecting for looseness and runout in the following steps.
Keep depressing the brake pedal to prevent the front drive shaft from rotating.
13.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY
43512
14.REMOVE FRONT DISC
Click hereBrake>BRAKE (FRONT)>FRONT BRAKE>REMOVAL
15.INSPECT FRONT AXLE HUB BEARING LOOSENESS
16.INSPECT FRONT AXLE HUB RUNOUT
43512
17.INSTALL FRONT DISC
18.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY
89543
19.INSTALL FRONT SPEED SENSOR
Install the front speed sensor and front flexible hose to the front shock absorber assembly with the bolt and clamp.
Do not twist the front speed sensor when installing it.
Install the speed sensor harness bracket first and then the front flexible hose.
Install the front speed sensor to the steering knuckle with the bolt.
Do not twist the front speed sensor when installing it.
43502H
20.STAKE FRONT AXLE SHAFT NUT
Using a chisel and a hammer, stake the front axle shaft nut.
21.INSTALL FRONT WHEEL
22.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
23.CHECK FOR SPEED SENSOR SIGNAL