1. PRECAUTION
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD
3.SECURE STEERING WHEEL
4.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
5.REMOVE FRONT WHEELS
53852K
6.REMOVE FRONT WHEEL OPENING EXTENSION PAD LH (for RHD)
51442C
7.REMOVE ENGINE UNDER COVER LH
53851Z
8.REMOVE FRONT WHEEL OPENING EXTENSION PAD RH (for RHD)
51441C
9.REMOVE ENGINE UNDER COVER RH
53737B
10.REMOVE FRONT FENDER APRON SEAL LH
53736
11.REMOVE FRONT FENDER APRON SEAL RH
12601B
12.REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
17750A
13.REMOVE INLET AIR CLEANER ASSEMBLY
17735
14.REMOVE AIR CLEANER CAP SUB-ASSEMBLY
17801
15.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
17701
16.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
28800
17.REMOVE BATTERY
82121
18.DISCONNECT ENGINE WIRE
17771A
19.REMOVE NO. 1 AIR CLEANER BRACKET
17410
20.REMOVE FRONT EXHAUST PIPE ASSEMBLY
43502H
21.REMOVE FRONT AXLE SHAFT NUT LH
43501H
22.REMOVE FRONT AXLE SHAFT NUT RH
Perform the same procedure as for the LH side.
48810
23.SEPARATE FRONT STABILIZER LINK ASSEMBLY LH
48820B
24.SEPARATE FRONT STABILIZER LINK ASSEMBLY RH
Perform the same procedure as for the LH side.
45470
25.SEPARATE TIE ROD ASSEMBLY LH
45460
26.SEPARATE TIE ROD ASSEMBLY RH
Perform the same procedure as for the LH side.
48069
27.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
48068
28.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
43420
29.SEPARATE FRONT DRIVE SHAFT ASSEMBLY LH
43410
30.SEPARATE FRONT DRIVE SHAFT ASSEMBLY RH
Perform the same procedure as for the LH side.
45220
31.SEPARATE STEERING INTERMEDIATE SHAFT ASSEMBLY
12361A
32.SEPARATE FRONT ENGINE MOUNTING INSULATOR
Remove the 3 nuts and separate the front engine mounting insulator from the front frame assembly.
12372A
33.SEPARATE ENGINE MOUNTING INSULATOR LH
Remove the 2 hole plugs.
Remove the 3 nuts and separate the engine mounting insulator LH from the front frame assembly.
12362
34.SEPARATE ENGINE MOUNTING INSULATOR RH
Remove the 2 hole plugs.
Remove the 3 nuts and separate the engine mounting insulator RH from the front frame assembly.
12364A
35.SEPARATE ENGINE LATERAL CONTROL ROD (for Manual Transaxle)
Remove the 2 hole plugs.
Remove the 2 nuts to separate the engine lateral control rod from the front frame assembly.
12327A
36.REMOVE NO. 2 ENGINE MOUNTING STAY RH
37.INSTALL ENGINE HANGERS
| *1 | No. 1 Engine Hanger |
| *2 | No. 2 Engine Hanger |
Install the 2 engine hangers with the 2 bolts as shown in the illustration.
| Item | Part No. |
|---|---|
| No. 1 engine hanger | 12281-36020 |
| No. 2 engine hanger | 12282-36021 |
| Bolt | 91552-81040 or 91552-81025 |
38.INSTALL ENGINE SUPPORT BRIDGE
Remove the 2 hood support assemblies.
Click hereVehicle Exterior>DOOR / HATCH>HOOD SUPPORT>REMOVAL
Install SST to the vehicle body as shown in the illustration.
| *a | Support Shaft | *b | Side Member |
| *c | Cloth | *d | Front Side |
| *e | Correct | *f | Incorrect |
| *g | Front Suspension Nut | - | - |
| *a | Fuse Shackle |
| *b | Shackle (A) |
| *c | Correct |
| *d | Incorrect |
Make sure the fuse shackle is on the chain block side and the shackle (A) is on the division bar side as shown in the illustration so that the fuse bolt is visible and can be checked for deformation easily.
| *a | Fuse Bolt |
| *b | Correct |
| *c | Incorrect |
Make sure the fuse bolt is not deformed.
Prevent SST from contacting the vehicle body or windshield.
To prevent damage to the engine hood, place pieces of cloth between the engine hood and SST.
Lightly shake SST by hand to make sure it is securely installed while performing work.
Set the support shafts on level surfaces.
| *a | Support Shaft |
| *b | Sub Beam |
| *c | Side Member |
| *d | Threaded Portion |
Turn the threaded portion of each support shaft to adjust its height and make the sub beams parallel to the ground.
Connect the chain to the division bar with the shackle at the position shown in the illustration.
| *1 | No. 1 Engine Hanger | *2 | No. 2 Engine Hanger |
| *a | Division Bar | *b | Shackle (A) |
| *c | Shackle (B) | - | - |
Connect the division bar and No. 1 engine hanger with the shackle (B).
Connect the 2nd link of the chain to the No. 2 engine hanger.
Make sure the distance between the chain block assembly and suspension ring is 20 mm (0.787 in.) or more.
| *a | Chain Block Assembly | *b | Suspension Ring |
| *c | 20 mm (0.787 in.) or more | - | - |
Adjust the position of the chain block assembly so that the chain is perpendicular to the main beam and sub beams as shown in the illustration.
| *a | Chain Block Assembly | *b | Main Beam |
| *c | Sub Beam | *d | Dimension (A) |
| *e | Dimension (B) | *f | Correct |
| *g | Incorrect | *h | Right to Left Adjustment |
| *i | Front to Rear Adjustment | - | - |
To prevent the engine assembly with transaxle assembly from falling, make sure that the dimension (A) and dimension (B) are equal.
Tighten the 6 wing bolts and 2 bolts.
| *a | Approximately 50 mm (1.97 in.) |
Move the chain block assembly approximately 50 mm (1.97 in.) as shown in the illustration.
| *a | Turn |
Tighten the chain block assembly until it cannot be moved any further by hand.
| *a | Chain Block Assembly |
| *b | Suspension Ring |
| *c | Roller |
| *d | Incorrect |
| *e | Correct |
If the suspension ring contacts the roller of the chain block assembly, the chain block assembly may be damaged. Do not tighten the chain block assembly excessively.
When suspending the engine assembly with transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).
Do not shake the engine assembly with transaxle assembly excessively while it is being suspended.
39.INSTALL BELT
Remove the bolt and nut.
Loosen the bolt and disconnect the windshield washer jar assembly from the vehicle body.
Do not remove the bolt.
Install SST to the vehicle body as shown in the illustration.
Using the SST ratchet buckle, tighten the SST belt until there is no slack.
| *a | Ratchet Buckle | - | - |
51100G
40.REMOVE FRONT FRAME ASSEMBLY
| *a | Chain Block Assembly |
Wind the chain with the chain block assembly to lift the engine assembly with transaxle assembly.
When suspending the engine assembly with transaxle assembly, do not tighten the chain block assembly more than 50 N*m (510 kgf*cm, 37 ft.*lbf).
Lift the engine assembly with transaxle assembly until the engine assembly is slightly raised off the front frame assembly.
Do not lift the engine assembly with transaxle assembly excessively.
| *a | Engine Lifter |
| *b | Attachment |
|
Attachment Placement Location |
Support the front frame assembly with an engine lifter using 4 attachments or equivalent tools as shown in the illustration.
The front frame assembly is a heavy component. Make sure that it is supported securely.
Make sure to secure the front frame assembly to prevent it from dropping.
Use the attachments to keep the front frame assembly level.
Remove the 4 bolts, 2 nuts and frame side rail plates RH and LH.
Remove the 4 bolts, 2 nuts and front suspension member rear braces RH and LH.
Slowly lower the front frame assembly.
When lowering the front frame assembly, be careful not to damage the vehicle body or other components installed to the vehicle.
48829A
41.REMOVE FRONT NO. 1 STABILIZER BRACKET LH
48824A
42.REMOVE FRONT NO. 1 STABILIZER BRACKET RH
Perform the same procedure as for the LH side.
43.REMOVE FRONT STABILIZER BAR WITH FRONT STABILIZER LINK ASSEMBLY
Remove the front stabilizer bar with 2 front stabilizer link assemblies from the front frame assembly.
44.REMOVE STEERING LINK ASSEMBLY
48069
45.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH
Remove the 3 bolts, nut and front lower No. 1 suspension arm sub-assembly LH from the front frame assembly.
When removing the bolt, keep the nut from rotating.
Remove the front lower arm bushing stopper from the front lower No. 1 suspension arm sub-assembly LH.
48068
46.REMOVE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY RH
Perform the same procedure as for the LH side.
51227B
47.REMOVE FRONT SUSPENSION MEMBER DYNAMIC DAMPER
Remove the 2 bolts and front suspension member dynamic damper from the front frame assembly.
52213A
48.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT STOPPER
Remove the 2 front suspension member body mounting front stoppers from the front frame assembly.
52216B
49.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR STOPPER
Remove the 2 front suspension member body mounting rear stoppers from the front frame assembly.
52211J
50.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING FRONT CUSHION
| *1 | Front Suspension Member Body Mounting Front Cushion |
Install SST as shown in the illustration.
| *a | Turn |
| *b | Hold |
Using SST, remove the front suspension member body mounting front cushion from the front frame assembly.
Make sure that the claws of SST are securely hung onto the mounting cushion.
Tighten SST slowly and evenly.
Be careful as the mounting cushion may fly out.
The mounting cushion cannot be reused.
52217E
51.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION LH
| *1 | Front Suspension Member Body Mounting Rear Cushion LH |
Install SST as shown in the illustration.
| *a | Turn |
| *b | Hold |
Using SST, remove the front suspension member body mounting rear cushion LH from the front frame assembly.
Make sure that the claws of SST are securely hung onto the mounting cushion.
Tighten SST slowly and evenly.
Be careful as the mounting cushion may fly out.
The mounting cushion cannot be reused.
52215
52.REMOVE FRONT SUSPENSION MEMBER BODY MOUNTING REAR CUSHION RH
Perform the same procedure as for the LH side.
53.REMOVE HOLE PLUG
for Automatic Transaxle:
Remove 5 hole plugs from the front frame assembly.
for Manual Transaxle:
Remove 4 hole plugs from the front frame assembly.