DTC P1603 Engine Stall History |
DTC P1605 Rough Idling |
| DTC No. | DTC Detection Condition | Trouble Area |
| P1603 | After monitoring for startability problems (P1604) finishes and 5 seconds or more elapse after starting the engine, with the engine running, the engine stops (the engine speed drops to 200 rpm or less) without the ignition switch being operated for 0.5 seconds or more (1 trip detection logic). |
|
| DTC No. | DTC Detection Condition | Trouble Area |
| P1605 | After 5 seconds or more elapse after starting the engine, with the engine running, the engine speed drops to 400 rpm or less (1 trip detection logic). |
|
| Reference waveforms showing a normal cold engine start |

| Reference waveforms showing a normal warm engine start |

| Reference values when there is an air leak in the intake system during rough idling |
| Parameter | -3 | -2 | -1 | 0 | 1 | Unit |
| Engine Speed | 533 | 516 | 612 | 420 | 416 | rpm |
| Calculate Load | 39.2 | 40.0 | 40.0 | 41.1 | 42.3 | % |
| Vehicle Load | 24.7 | 27.0 | 16.8 | 40.7 | 35.2 | % |
| MAF | 3.56 | 3.75 | 2.81 | 4.59 | 3.93 | gm/sec |
| Atmosphere Pressure | 14.5 | 14.5 | 14.5 | 14.5 | 14.5 | psi(gauge) |
| Coolant Temp | 189 | 189 | 189 | 189 | 189 | F |
| Intake Air | 109 | 109 | 109 | 109 | 109 | F |
| Battery Voltage | 13.105 | 13.144 | 13.359 | 12.949 | 12.910 | V |
| Throttle Sensor Volt % | 17.2 | 15.6 | 15.2 | 16.8 | 16.4 | % |
| Throttl Sensor #2 Volt % | 49.4 | 47.4 | 47.0 | 49.0 | 48.6 | % |
| Throttle Sensor Position | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | % |
| Throttle Motor DUTY | 17.6 | 15.2 | 15.2 | 15.2 | 16.8 | % |
| Injector (Port) | 4160 | 4194 | 4056 | 4979 | 5042 | μs |
| Injection Volum (Cylinder 1) | 0.175 | 0.175 | 0.228 | 0.228 | 0.228 | ml |
| Fuel Pump/Speed Status | ON | ON | ON | ON | ON | |
| EVAP (Purge) VSV | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | % |
| Evap Purge Flow | 0.0 | 0.0 | 0.0 | 0.0 | 0.0 | % |
| Purge Density Learn Value | 0.000 | 0.000 | 0.000 | 0.000 | 0.000 | |
| EVAP Purge VSV | OFF | OFF | OFF | OFF | OFF | |
| Target Air-Fuel Ratio | 0.999 | 0.999 | 0.999 | 0.999 | 0.999 | |
| AF Lambda B1S1 | 1.232 | 1.232 | 1.232 | 1.232 | 1.232 | |
| AFS Voltage B1S1 | 4.996 | 4.996 | 4.996 | 4.996 | 4.996 | V |
| O2S B1S2 | 0.000 | 0.000 | 0.000 | 0.000 | 0.000 | V |
| Short FT #1 | 18.750 | 18.750 | 18.750 | 18.750 | 18.750 | % |
| Long FT #1 | 3.906 | 3.906 | 3.906 | 3.906 | 3.906 | % |
| Total FT #1 | 0.000 | 0.000 | 0.000 | 0.000 | 0.000 | |
| Fuel System Status #1 | CL | CL | CL | CL | CL | |
| IGN Advance | 15.0 | 14.0 | 14.5 | 15.0 | 0.5 | deg |
| Knock Feedback Value | -3.0 | -3.0 | -3.0 | -3.0 | -3.0 | °CA |
| Knock Correct Learn Value | 19.0 | 19.0 | 19.0 | 19.0 | 19.0 | °CA |
| VVT Control Status #1 | OFF | OFF | OFF | OFF | OFF | |
| Starter Signal | Close | Close | Close | Close | Close |
| Symptom | Suspected Area |
| Engine vibration occurs and engine stops | Air fuel ratio abnormal |
| Engine stops with no engine vibration | Ignition system, injection stoppage, high load from external parts |
| Engine can be started with accelerator pedal depressed | Insufficient air volume |
| Rough idling after engine started | Air fuel ratio abnormal, abnormal combustion |

| Vehicle State | Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Idling or decelerating | Slowly decreases and engine stalls | Air fuel ratio abnormal | Air suction |
| 3 to 6 |
| Sensor malfunction (value from sensor too lean) |
| 7 to 16 | |||
| Sensor malfunction (value from sensor too rich) | 25 to 34 | ||||
| Fuel supply problem |
| 17 to 24 | |||
| Intake air volume insufficient | ISC flow rate |
| 35 to 37 | ||
| Excessive valve overlap |
| 38, 39 | |||
| Ignition timing incorrect | Does not operate as expected |
| 40 to 42 | ||
| Rapidly decreases and engine stalls | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 43, 44 | |
| External part malfunctioning | Increase in load |
| 47 to 50 | ||
| Accelerating | - | Crankshaft position sensor, camshaft position sensor malfunction | Power temporarily cut |
| 1 |
| Mass air flow meter sub-assembly | Foreign matter adhesion |
| 52 | ||
| Fuel supply problem | Fuel leak, clog |
| 55 to 57 | ||
| Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 53, 54 | ||

| Engine Speed | Suspected Area | Primary Parts to Inspect | Procedure | |
| Slowly decreases | Air fuel ratio abnormal | Air suction |
| 3 to 6 |
| Sensor malfunction (value from sensor too lean) |
| 7 to 16 | ||
| Sensor malfunction (value from sensor too rich) | 25 to 34 | |||
| Fuel supply problem |
| 17 to 24 | ||
| Intake air volume insufficient | ISC flow rate |
| 35 to 37 | |
| Ignition timing incorrect | Does not operate as expected |
| 40 to 42 | |
| Rapidly decreases | Ignition and injection stops (electrical system malfunction) | Power temporarily cut |
| 43, 44 |
| External part malfunctioning | Increase in load |
| 47 to 50 | |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1603 AND/OR P1605) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs (Click here).
| Result | Proceed to |
| DTC P1603 and/or P1605 is output | A |
| DTC P1603 or P1605 and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Problem Symptom | Freeze Frame Data Item | Suspected Area | Proceed to | ||
| Closed Throttle Position SW | Engine Speed | Total of Short FT #1 and Long FT #1 | |||
| When idling or decelerating, engine speed slowly decreases (and engine stalls) | All 5 sets of freeze frame data are ON | Decreases slowly*1 | All 5 sets of freeze frame data are +15% or higher*2 |
| A |
| At least 1 of the 5 sets of freeze frame data is -15% or less*3 | Sensor malfunction (value from sensor too rich) | B | |||
| All 5 sets of freeze frame data are between -15% and +15% |
| C | |||
| When idling or decelerating, engine speed rapidly decreases (and engine stalls) | Decreases rapidly*1 | - |
| D | |
| When accelerating or driving at constant speed, engine stalls*4 | At least one is OFF | - | - |
| E |

|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK INTAKE SYSTEM |
Check for air leaks in the intake system (vacuum hose disconnection, cracks, damaged gaskets, etc.) .
|
| ||||
| OK | |
| 4.CHECK PURGE VSV |
![]() |
Disconnect the fuel vapor feed hose (on the canister side) of the purge VSV.
| *1 | Fuel Vapor Feed Hose (to Canister) |
| *2 | Connector |
| *3 | Purge VSV |
Start the engine.
Idle the engine.
Disconnect the connector of the purge VSV.
Check if air flows through the purge VSV.
|
| ||||
| OK | |
| 5.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Stop Light Switch | At least 1 of the 5 sets of freeze frame data is ON | Air suction from brake booster assembly | A |
| All 5 sets of freeze frame data are OFF | - | B |
|
| ||||
| A | |
| 6.READ VALUE USING INTELLIGENT TESTER (SHORT FT #1) |
![]() |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Start the engine and warm it up until the engine coolant temperature stabilizes.
Idle the engine.
Using the tester, read [Short FT #1] of the Data List while depressing the brake pedal.
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 7.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Calculate Load | Below 90% of the current value of the vehicle*1 | Mass air flow meter sub-assembly | A |
| AFS Voltage B1S1 | 3.3 V or higher*2 |
| B |
| Both freeze frame data items listed above | Values are other than above | - | C |
|
| ||||
|
| ||||
| A | |
| 8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Remove the mass air flow meter sub-assembly.
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
|
| ||||
| A | ||
| ||
| 9.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2.
Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.
| Tester Display | Specified Condition |
| Control the Injection Volume (12%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume (-12%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR) |
Check the harnesses and connectors, referring to DTC P0031 inspection procedure .
|
| ||||
| OK | |
| 11.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P2237 inspection procedure .
|
| ||||
| OK | ||
| ||
| 12.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Proceed to |
| Initial Engine Coolant Temp, Initial Intake Air Temp | Difference in temperature between each item is below 10°C (18°F)*1 | A |
| Difference in temperature between each item is 10°C (18°F) or higher*2 | B |
|
| ||||
| A | |
| 13.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).

| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 14.INSPECT THERMOSTAT |
Inspect the thermostat (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 15.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C (248°F) or higher | Engine coolant temperature sensor | A |
| Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher | Engine coolant temperature sensor | ||
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 16.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 17.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| EVAP (Purge) VSV | At least 1 of the 5 sets of freeze frame data is not 0% | Purge VSV | A |
| All 5 sets of freeze frame data are 0% | - | B |
|
| ||||
| A | |
| 18.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL) |
![]() |
Disconnect the fuel vapor feed hose (on the canister side) of the purge VSV.
| *1 | Purge VSV |
| *2 | Fuel Vapor Feed Hose (to Canister) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
Operate the purge VSV and check the air flow.
| Activate the VSV for Evap Control | Specified Condition |
| ON | Air flows |
| OFF | Air does not flow |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 19.INSPECT PURGE VSV |
Inspect the purge VSV (Click here).
|
| ||||
| OK | |
| 20.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV) |
Check the harnesses and connectors, referring to DTC P0443 inspection procedure .
|
| ||||
| OK | |
| 21.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
Check the harnesses and connectors, referring to DTC P0443 inspection procedure .
|
| ||||
| OK | ||
| ||
| 22.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 23.INSPECT FUEL PUMP (RESISTANCE) |
Inspect the fuel pump (Click here).
|
| ||||
| OK | ||
| ||
| 24.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | ||
| ||
| 25.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Calculate Load | 110% or higher of the current value of the vehicle*1 | Mass air flow meter sub-assembly | A |
| AFS Voltage B1S1 | Below 3.3 V*2 |
| B |
| Both freeze frame data items listed above | Values are other than above | - | C |
|
| ||||
|
| ||||
| A | |
| 26.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Remove the mass air flow meter sub-assembly.
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
|
| ||||
| A | ||
| ||
| 27.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE INJECTION VOLUME) |
![]() |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / All Data / AFS Voltage B1S1 and O2S B1S2.
Change the fuel injection volume using the tester, and monitor the voltage output of the air fuel ratio and heated oxygen sensors displayed on the tester.
| Tester Display | Specified Condition |
| Control the Injection Volume (12%) | Air fuel ratio sensor output voltage is below 3.1 V |
| Control the Injection Volume (-12%) | Air fuel ratio sensor output voltage is higher than 3.4 V |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 28.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR) |
Check the harnesses and connectors, referring to DTC P0031 inspection procedure .
|
| ||||
| OK | |
| 29.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Check the harnesses and connectors, referring to DTC P2237 inspection procedure .
|
| ||||
| OK | ||
| ||
| 30.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Proceed to |
| Initial Engine Coolant Temp, Initial Intake Air Temp | Difference in temperature between each item is below 10°C (18°F)*1 | A |
| Difference in temperature between each item is 10°C (18°F) or higher*2 | B |
|
| ||||
| A | |
| 31.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions present when the DTC was stored which are recorded in the freeze frame data (Click here).

| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Initial Engine Coolant Temp, Coolant Temp, Engine Run Time | Range A |
| A |
| Range B | Engine coolant temperature sensor | B | |
| Range C | - | C |
|
| ||||
|
| ||||
| A | |
| 32.INSPECT THERMOSTAT |
Inspect the thermostat (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 33.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Coolant Temp | 120°C (248°F) or higher | Engine coolant temperature sensor | A |
| Engine coolant temperature is lower than outside temperature* by 15°C (27°F) or higher | Engine coolant temperature sensor | ||
| Both freeze frame data items listed above | Values are other than above | - | B |
|
| ||||
| A | |
| 34.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 35.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Total of ISC Learning Value and ISC Feedback Value | Below 80% of the current value of the vehicle*1 | Throttle with motor body assembly | A |
| 120% or higher of the current value of the vehicle*2 | B | ||
| From 80 to 120% of the current value of the vehicle | - | C |
|
| ||||
|
| ||||
| A | |
| 36.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY |
Check for foreign matter and signs that the throttle with motor body assembly was stuck, and also check that the valve and shaft move smoothly during operation.
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | ||
| ||
| 37.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY |
Check if carbon is in the air flow passage of the throttle with motor body assembly.
| Result | Proceed to |
| Carbon in passage | A |
| No carbon in passage | B |
|
| ||||
| A | ||
| ||
| 38.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR) |
Perform the Active Test, referring to DTC P0011 inspection procedure .
|
| ||||
| OK | |
| 39.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT EXHAUST LINEAR) |
Perform the Active Test, referring to DTC P0014 inspection procedure .
|
| ||||
| OK | |
| 40.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
| IGN Advance | Knock Correct Learn Value | ||
| Differs from the current value of the vehicle by 10 deg or higher | Below 3°CA |
| A |
| 3°CA or higher | - | B | |
| Differs from the current value of the vehicle by less than 10 deg | - | - | |
|
| ||||
| A | |
| 41.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
| Result | Proceed to |
| Normal | A |
| Abnormal | B |
|
| ||||
| A | |
| 42.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY (INTAKE AIR TEMPERATURE SENSOR) |
Inspect the mass air flow meter sub-assembly (intake air temperature sensor) (Click here).
| Result | Proceed to |
| Normal | A |
| Abnormal | B |
|
| ||||
| A | ||
| ||
| 43.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40) |
Check the harnesses and connectors, referring to DTC P0300 inspection procedure .
|
| ||||
| OK | |
| 44.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY) |
Check the harnesses and connectors, referring to DTC P0351 inspection procedure .
|
| ||||
| OK | |
| 45.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Idle Spark Advn Ctrl (#1 to #4) | At least one cylinder shows a value of 4°CA or higher |
| A |
| All cylinders show a value of less than 4°CA | - | B |
|
| ||||
| A | |
| 46.READ VALUE USING INTELLIGENT TESTER (IDLE SPARK ADVN CTRL #) |
Change the location of the ignition coil assembly for the cylinder whose Idle Spark Advn Ctrl (#1 to #4) was 4°CA or more in step 45.
Connect the intelligent tester to the DLC3.
Start the engine.
Using the tester, select [Idle Spark Advn Ctrl (#1 to #4)] of the Data List.
| Result | Proceed to |
| Same as result in step 45 | A |
| Different from result in step 45 | B |
|
| ||||
| A | |
| 47.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | ||
| A/C Signal | Air Conditioner FB Val | Power Steering Signal | ||
| A/C Signal display changes from OFF to ON | Value displayed for Air Conditioner FB Val increases | Does not change from OFF | A/C system | B |
| Changes from OFF to ON | Power steering system | A | ||
| A/C Signal display does not change from OFF | Value displayed for Air Conditioner FB Val does not increase | Changes from OFF to ON | ||
| Does not change from OFF | - | |||
|
| ||||
| A | |
| 48.CHECK AUTOMATIC TRANSAXLE ASSEMBLY |
Start the engine.
Move the shift lever to R and confirm that the vehicle can move rearward.
|
| ||||
| OK | |
| 49.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |||
| Electrical Load Signal 1 (3) | Electric Load Feedback Val | Difference between Engine Speed and SPD (NT) | Vehicle Speed | ||
| Electrical Load Signal 1 (3) display changes from OFF to ON*1, or value displayed for Electric Load Feedback Val increases*1 | Value displayed for Electric Load Feedback Val changes | - | - | Electrical load signal circuit | A |
| Value displayed for Electric Load Feedback Val does not change | At least 1 of the 5 sets of freeze frame data is below 100 rpm | Below 15 km/h (9 mph) | A/T system | B | |
| 15 km/h (9 mph) or more | - | C | |||
| All 5 sets of freeze frame data are 100 rpm or higher | - | - | C | ||
| Electrical Load Signal 1 (3) display does not change from OFF, or value displayed for Electric Load Feedback Val does not increase | - | At least 1 of the 5 sets of freeze frame data is below 100 rpm | Below 15 km/h (9 mph) | A/T system | B |
| 15 km/h (9 mph) or more | - | C | |||
| All 5 sets of freeze frame data are 100 rpm or higher | - | - | C | ||
|
| ||||
|
| ||||
| A | ||
| ||
| 50.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Suspected Area | Proceed to | |
| Shift SW Status (P or N Range) | Neutral Position SW Signal | ||
| P and N position are both OFF in at least one data set | ON when Shift SW Status D or R | Park/neutral position switch | A |
| OFF when Shift SW Status D or R | A/T system | B | |
| All 5 sets of freeze frame data are ON | - | - | C |
|
| ||||
|
| ||||
| A | ||
| ||
| 51.READ FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Using the tester, confirm the vehicle conditions recorded in the freeze frame data which were present when the DTC was stored (Click here).
| Freeze Frame Data Item | Result | Suspected Area | Proceed to |
| Throttle Sensor Position, Calculate Load | Calculate Load decreases while Throttle Sensor Position increases | Mass air flow meter sub-assembly | A |
| Calculate Load does not decrease while Throttle Sensor Position increases | - | B |
|
| ||||
| A | |
| 52.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Remove the mass air flow meter sub-assembly.
Check for foreign matter in the air flow passage of the mass air flow meter sub-assembly.
| Result | Proceed to |
| Visible foreign matter is present | A |
| Visible foreign matter is not present | B |
|
| ||||
| A | ||
| ||
| 53.CHECK TERMINAL VOLTAGE (#10, #20, #30 AND/OR #40) |
Check the harnesses and connectors, referring to DTC P0300 inspection procedure .
|
| ||||
| OK | |
| 54.CHECK TERMINAL VOLTAGE (POWER SOURCE OF IGNITION COIL ASSEMBLY) |
Check the harnesses and connectors, referring to DTC P0351 inspection procedure .
|
| ||||
| OK | |
| 55.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.
When performing the Active Test, check for an operating sound from the fuel pump.
| Control the Fuel Pump / Speed | Specified Condition |
| ON | Operating sound heard |
| OFF | Operating sound not heard |
| Result | Proceed to |
| Abnormal | A |
| Normal | B |
|
| ||||
| A | |
| 56.INSPECT FUEL PUMP |
Inspect the fuel pump (Click here).
|
| ||||
| OK | ||
| ||
| 57.CHECK FUEL SYSTEM |
Check for foreign matter such as iron particles around the fuel pump, and for signs that the fuel pump was stuck.
| Result | Proceed to |
| There is foreign matter or signs that fuel pump was stuck | A |
| There is no foreign matter and no signs that fuel pump was stuck | B |
|
| ||||
| A | ||
| ||
| 58.REPLACE MALFUNCTIONING PARTS |
If the malfunction could not be identified in steps 3 to 24, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 6 | Brake booster assembly replacement |
| Step 8 | Mass air flow meter sub-assembly replacement |
| Step 9 | Air fuel ratio sensor replacement |
| Step 16 | Engine coolant temperature sensor replacement |
| Step 18 | Purge VSV replacement |
| Step 24 | Fuel pump replacement |
If the malfunction could not be identified in steps 25 to 34, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 26 | Mass air flow meter sub-assembly replacement |
| Step 27 | Air fuel ratio sensor replacement |
| Step 34 | Engine coolant temperature sensor replacement |
If the malfunction could not be identified in steps 35 to 42, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 36, 37 | Throttle with motor body assembly replacement |
| Step 40 | Knock control sensor replacement |
If the malfunction could not be identified in steps 43 to 50, inspect and repair the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 47 | A/C system inspection and repair Power steering system inspection and repair |
| Step 48 | A/T system inspection and repair |
| Step 49 | Electrical load signal system inspection and repair A/T system inspection and repair |
| Step 50 | Park/neutral position switch inspection and repair A/T system inspection and repair |
If the malfunction could not be identified in steps 51 to 57, replace the part which is suspected to be malfunctioning according to the step where an inspection was performed.
| Performed Step | Inspection or Part to Replace |
| Step 52 | Mass air flow meter sub-assembly replacement |
| NEXT | |
| 59.CLEAR DTC |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Clear the DTCs (Click here).
| NEXT | |
| 60.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Check if engine stall symptoms are present.
|
| ||||
| OK | ||
| ||