DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2A00 | The calculated value for the air fuel ratio sensor response rate deterioration level is less than the threshold (2 trip detection logic). |
|

| Related DTCs | P2A00: Air fuel ratio sensor (sensor 1) slow response |
| Required Sensors/Components (Main) | Air fuel ratio sensor |
| Required Sensors/Components (Related) | Vehicle speed sensor Crankshaft position sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | 10 to 15 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0016 (VVT system - misalignment) P0017 (Exhaust VVT system - misalignment) P0031, P0032, P101D (Air fuel ratio sensor heater) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0128 (Thermostat) P0171, P0172 (Fuel system) P0301 - P0304 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) P0451, P0452, P0453 (EVAP system) P0500 (Vehicle speed sensor) P0505 (IAC valve) P219A (Air fuel ratio imbalance) |
| Active air fuel ratio control | Performing |
| Active air fuel ratio control is performed when the following conditions met | - |
| Battery voltage | 11 V or higher |
| Engine coolant temperature | 75°C (167°F) or higher |
| Idling | Off |
| Engine speed | 1200 rpm or higher, and less than 4000 rpm |
| Air fuel ratio sensor status | Activated |
| Fuel-cut | Off |
| Engine load | 10% or higher, and less than 70% |
| Shift position | 2nd or more |
| Catalyst monitor | Not yet |
| Mass air flow | 10 gm/sec or more, and less than 40 gm/sec |
| Response rate deterioration level | Below 0.12 V |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $01 | $8E | Multiply by 0.001 | V | A/F sensor deterioration level |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P2A00 is output | A |
| DTC P2A00 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume / Gas AF Control / AFS Voltage B1S1 and O2S B1S2.
Perform the Control the Injection Volume operation with the engine idling.
Monitor the output voltages of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | +12% | Rich | Below 3.1 V |
| AFS Voltage B1S1 (Air fuel ratio) | -12% | Lean | Higher than 3.4 V |
| O2S B1S2 (Heated oxygen) | +12% | Rich | Higher than 0.55 V |
| O2S B1S2 (Heated oxygen) | -12% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 | Status of O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Proceed to |
| Lean/Rich | Lean/Rich | Normal | A |
| Lean | Lean | Actual air fuel ratio lean | B |
| Rich | Rich | Actual air fuel ratio rich | B |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | C |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2A00.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P2A00 is output) | B |
|
| ||||
| A | ||
| ||
| 4.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 5.CHECK INTAKE SYSTEM |
Check the intake system .
|
| ||||
| OK | |
| 6.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 7.INSPECT FUEL INJECTOR ASSEMBLY |
Inspect the fuel injector assembly (Click here).
|
| ||||
| OK | |
| 8.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2A00.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P2A00 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 10.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 11.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P2A00.
Check that the DTC judgment result is NORMAL.
| NEXT | ||
| ||
| 12.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||