DTC P0014 Camshaft Position "B" - Timing Over-Advanced or System Performance (Bank 1) |
DTC P0015 Camshaft Position "B" - Timing Over-Retarded (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0014 | Exhaust valve timing is stuck at a certain value when in the advance range (2 trip detection logic). |
|
| P0015 | Exhaust valve timing is stuck at a certain value when in the retard range (1 trip detection logic). |
| Related DTCs | P0014: Advanced camshaft timing P0015: Retarded camshaft timing |
| Required Sensors/Components (Main) | Camshaft timing oil control valve Camshaft timing exhaust gear assembly |
| Required Sensors/Components (Related) | Crankshaft position sensor Camshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Continuous |
| Duration | Within 10 seconds |
| MIL Operation | Advanced camshaft timing: 2 driving cycles Retarded camshaft timing: Immediate |
| Sequence of Operation | None |
| Monitor runs whenever the following DTCs are not stored | P0013 (Exhaust VVT oil control valve) P0017 (Exhaust VVT system - misalignment) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0335 (Crankshaft position sensor) P0340, P0342, P0343 (Camshaft position sensor) |
| Battery voltage | 11 V or higher |
| Engine speed | 500 to 4000 rpm |
| Engine coolant temperature | 75 to 100°C (167 to 212°F) |
| Both of the following conditions are met | - |
| Deviation of actual valve timing and target valve timing | More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit. |
| Valve timing | No change at advanced valve timing |
| Both of the following conditions are met | - |
| Deviation of actual valve timing and target valve timing | More than 5°CA (Crankshaft Angle) for 5 seconds or more after the VVT hold duty ratio learned value reaches the upper or lower limit. |
| Valve timing | No change at retarded valve timing |
| Monitor ID | Test ID | Scaling | Unit | Description |
| $35 | $85 | Multiply by 0.01 | Second | Forced movement of oil control valve time |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0014 OR P0015) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0014 or P0015 is output | A |
| DTC P0014 or P0015 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE VVT EXHAUST LINEAR) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Turn the A/C switch on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1).
Check the engine speed while operating the camshaft timing oil control valve assembly (for exhaust camshaft) using the Techstream.
| Techstream Operation | Specified Condition |
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0014 or P0015 is output | B |
|
| ||||
| A | ||
| ||
| 4.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH) |

| *1 | Timing Mark | - | - |
Remove the cylinder head cover sub-assembly.
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
|
| ||||
| OK | |
| 5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT) |
Inspect the camshaft timing oil control valve assembly (for exhaust camshaft) (Click here).
|
| ||||
| OK | |
| 6.INSPECT OIL CONTROL VALVE FILTER |
Remove the oil control valve filter .
Check that the filter is not clogged.
|
| ||||
| OK | |
| 7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY |
Replace the camshaft timing exhaust gear assembly (Click here).
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P0014 OR P0015) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON.
Turn the Techstream on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read the pending DTCs.
| Result | Proceed to |
| DTC is not output | A |
| DTC P0014 or P0015 is output | B |
|
| ||||
| A | ||
| ||