AIR CONDITIONING UNIT > INSTALLATION |
| 1. INSTALL AIR CONDITIONING UNIT ASSEMBLY |
Install the air conditioning unit assembly to the instrument panel reinforcement assembly with the 3 bolts.

| 2. INSTALL TRANSPONDER KEY ECU ASSEMBLY (w/ Engine Immobiliser System) |
Connect the connector and install the transponder key ECU assembly.
| 3. INSTALL INSTRUMENT PANEL REINFORCEMENT ASSEMBLY WITH AIR CONDITIONING UNIT |
w/ Engine Immobiliser System:
Disengage the 3 guides and temporarily install the instrument panel reinforcement assembly with air conditioning unit as shown in the illustration.

| *A | w/ Engine Immobiliser System | - | - |
Install the instrument panel reinforcement assembly with the 3 bolts <A> and 2 new bolts <B>in the order shown in the illustration.

| *1 | Movable Collar | *2 | Body |
| *3 | Instrument Panel Reinforcement | - | - |
| *a | Step 1 | *b | Step 2 |
| *c | Step 3 | *d | Step 4 |
Install the bolt.
Install the instrument panel reinforcement assembly with air conditioning unit with the nut.
![]() |
Pass the cooler drain hose through the vehicle securely.
![]() |
Install the 2 bolts.
Engage each clamp.
Connect each connector.
Connect the bolts and connect the 3 earth wires.
for Power Tilt and Power Telescopic Steering Column:
Connect the protector with the nut.
Engage the claw to connect the airbag connector as shown in the illustration.

![]() |
Engage the 2 claws to lock the retainer as shown in the illustration.
| *1 | Retainer |
![]() |
Engage each clamp.
| *A | w/ Smart Key System |
| *a | Airbag Sensor Assembly |
Connect each connector.
Engage the 2 clamps.
Connect the connector to the airbag sensor assembly as shown in the illustration.
![]() |
Engage the 3 claws to close the 3 clamps as shown in the illustration.
w/ Manual (SOS) Switch:
Engage the clamp.
for 10 Speakers:
Engage the 3 clamps.
| 4. INSTALL FRONT LOWER PANEL PACKING |
![]() |
Install the 2 front lower panel packings shown in the illustration.
| 5. INSTALL INSTRUMENT PANEL SAFETY PAD CAP |
![]() |
Install 5 new instrument panel safety pad caps.
| *A | for LH Side |
| *B | for RH Side |
| 6. INSTALL NO. 2 INSTRUMENT PANEL BRACE SUB-ASSEMBLY |
Install the screw and 2 nuts.
Install the No. 2 instrument panel brace sub-assembly with the bolt.
Connect the earth wire with the bolt.
Engage each clamp.
Connect the connector.
| 7. INSTALL INSTRUMENT PANEL TO COWL BRACE SUB-ASSEMBLY |
Install the screw and 2 nuts.
Install the instrument panel to cowl brace sub-assembly with the bolt.
Connect the earth wire with the bolt.
Engage each clamp.
Connect each connector.
| 8. INSTALL NO. 1 CONSOLE BOX DUCT (w/ Rear Register Duct) |
Install the No. 1 console box duct with the clip.
| 9. INSTALL REAR NO. 3 AIR DUCT |
Engage the 2 claws to install the rear No. 3 air duct.
| 10. INSTALL FLOOR CARPET BRACKET LH |
Engage the 2 guides.
Install the floor carpet bracket LH with the 2 clips.
| 11. INSTALL REAR NO. 4 AIR DUCT |
![]() |
Engage the 4 claws to install the rear No. 4 air duct as shown in the illustration.
![]() |
Engage the guide to install the floor carpet to the original position as shown in the illustration.
| 12. CONNECT FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY |
![]() |
Engage the guide to connect the fuel lid lock open lever sub-assembly as shown in the illustration.
Install the screw.
| 13. INSTALL REAR NO. 1 AIR DUCT |
Engage the 2 claws to install the rear No. 1 air duct.
| 14. INSTALL FLOOR CARPET BRACKET RH |
Engage the 2 guides.
Install the floor carpet bracket RH with the 2 clips.
| 15. INSTALL REAR NO. 2 AIR DUCT |
![]() |
Engage the 4 claws to install the rear No. 2 air duct as shown in the illustration.
![]() |
Engage the guide to install the floor carpet to the original position as shown in the illustration.
| 16. INSTALL FLOOR CARPET HOOK |
Engage the 6 claws to install the 6 floor carpet hooks.
Engage the 6 guides.
| 17. INSTALL AIR CONDITIONING AMPLIFIER ASSEMBLY |
Engage the 2 guides.
Install the air conditioning amplifier assembly with the 2 screws.
Connect each connector.
| 18. INSTALL CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/o ECU Integration Box RH) |
w/ ECU Integration Box RH:
Engage the 2 claws and install the certification ECU (smart key ECU assembly).
w/o ECU Integration Box RH:
Install the certification ECU (smart key ECU assembly) with the nut and bolt.
Connect each connector.
| 19. INSTALL ECU INTEGRATION BOX RH (w/ ECU Integration Box RH) |
Install the ECU integration box RH with the 2 nuts and bolt.
Engage the clamp.
Connect each connector.
| 20. INSTALL STEERING COLUMN ASSEMBLY |
| 21. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY |
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
![]() |
Connect the airbag connector to the lower No. 1 instrument panel airbag assembly.
| *1 | Airbag Connector |
| *2 | Airbag Connector Lock |
Push in the lock to install the airbag connector.
Temporarily install the lower No. 1 instrument panel airbag assembly with the 2 hooks.
Engage the 2 claws to install the DLC3.
Install the 4 bolts.
| 22. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY |
| 23. INSTALL STEREO COMPONENT AMPLIFIER ASSEMBLY WITH BRACKET (for 10 Speakers) |
Engage the 2 guides to the vehicle body to temporarily install the stereo component amplifier assembly with bracket.
Install the stereo component amplifier assembly with bracket with the bolt.
Engage the clamp.
Connect each connector.
Connect the ground wire with the bolt.
| 24. INSTALL AUDIO AMPLIFIER COVER (for 10 Speakers) |
Install the audio amplifier cover with the 2 clips.
| 25. INSTALL FRONT SEAT ASSEMBLY LH (for TMMK Made Manual Seat) |
| 26. INSTALL FRONT SEAT ASSEMBLY LH (for TMMK Made Power Seat) |
| 27. INSTALL FRONT SEAT ASSEMBLY LH (for SIA Made Manual Seat) |
| 28. INSTALL FRONT SEAT ASSEMBLY LH (for SIA Made Power Seat) |
| 29. INSTALL DCM (TELEMATICS TRANSCEIVER) WITH BACK-UP BATTERY (w/ Manual (SOS) Switch) |
Engage the 2 guides to the vehicle body to temporarily install the DCM (telematics transceiver) with back-up battery.
Install the DCM (telematics transceiver) with back-up battery with the bolt.
Connect each connector.
Engage the 3 clamps.
| 30. INSTALL AUDIO AMPLIFIER COVER (w/ Manual (SOS) Switch) |
Install the audio amplifier cover with the 2 clips.
| 31. INSTALL FRONT SEAT ASSEMBLY RH (for TMMK Made Manual Seat) |
| 32. INSTALL FRONT SEAT ASSEMBLY RH (for TMMK Made Power Seat) |
| 33. INSTALL FRONT SEAT ASSEMBLY RH (for SIA Made Manual Seat) |
| 34. INSTALL FRONT SEAT ASSEMBLY RH (for SIA Made Power Seat) |
| 35. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY |
Remove the vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and fitting surface of the air conditioning tube and accessory assembly.
Install the O-ring to the air conditioning tube and accessory assembly.
Install the air conditioning tube and accessory assembly.
| 36. CONNECT SUCTION HOSE SUB-ASSEMBLY (for TMMK Made) |
Remove the vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction hose sub-assembly.
Connect the O-ring to the suction hose sub-assembly.
Connect the suction hose sub-assembly.
![]() |
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 37. CONNECT SUCTION PIPE SUB-ASSEMBLY (for SIA Made) |
Remove the vinyl tape from the pipe.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the suction pipe sub-assembly.
Connect the O-ring to the suction pipe sub-assembly.
Connect the suction pipe sub-assembly.
![]() |
Move the hook connector in the direction indicated by the arrow in the illustration.
Insert the pipe joint into the fitting hole securely and tighten the bolt.
| 38. CONNECT HEATER INLET WATER HOSE |
Install the heater inlet water hose and attach the clip.
| 39. CONNECT HEATER OUTLET WATER HOSE |
Install the heater outlet water hose and attach the clip.
| 40. INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY |
Install the front outer cowl top panel sub-assembly with the 10 bolts.
Engage the 2 clamps to install the wire harness to the front outer cowl top panel sub-assembly.
| 41. INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY |
| 42. ADD ENGINE COOLANT (for 2AR-FE) |
Tighten the radiator drain cock plug by hand.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the No. 1 and No. 2 radiator hoses several times by hand to bleed air.
Stop the engine and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 43. ADD ENGINE COOLANT (for 2GR-FE) |
Tighten the radiator drain cock plug by hand.
Close the 2 cylinder block drain cock plugs.
Loosen the air drain cock plug on the water inlet housing.
Add TOYOTA Super Long Life Coolant (SLLC) to the radiator inlet opening until coolant overflows from the air drain cock hole. Then tighten the air drain cock plug to the water inlet housing.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reserve tank assembly until it reaches the full line.
Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reserve tank cap.
Bleed air from the cooling system.
Warm up the engine until the thermostat opens. While the thermostat is open, circulate the coolant for several minutes.
Maintain the engine speed at 2500 to 3000 rpm.
Squeeze the inlet and outlet radiator hoses several times by hand to bleed air.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the full line on the radiator reserve tank assembly.
| 44. INSPECT FOR COOLANT LEAK (for 2AR-FE) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 45. INSPECT FOR COOLANT LEAK (for 2GR-FE) |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 46. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT |
Perform vacuum purging using a vacuum pump or appropriate equipment.
Charge the air conditioning system with refrigerant.

| *a | Sub-cool System | *b | High Pressure |
| *c | Refrigerant Amount | *d | Standard charge amount |
| *e | Charge additional 100g (3.5oz.) | *f | Point where bubbles disappear |
| *g | Mean value in proper range | *h | Overcharged |
| 47. WARM UP ENGINE |
Keep the A/C switch on for at least 2 minutes to warm up the compressor.
| 48. INSPECT FOR REFRIGERANT LEAK |
After recharging the air conditioning system with refrigerant, inspect for refrigerant leaks using a halogen leak detector.
Carry out the test under the following conditions:
![]() |
Using a halogen leak detector, inspect for refrigerant leaks from the air conditioning system.
| *1 | Halogen Leak Detector |
| *a | Inspect for Leak |
![]() |
Bring the halogen leak detector close to the drain hose with the detector power off, and then turn the detector on.
| *1 | Halogen Leak Detector |
| *2 | Drain Hose |
If a refrigerant leak is not detected from the drain hose, remove the blower motor control from the cooling unit. Insert the halogen leak detector sensor into the unit and check for a leak.
Disconnect the pressure sensor connector and leave it for approximately 20 minutes. Bring the halogen leak detector close to the pressure sensor and check for a leak.
| 49. INITIALIZATION SERVO MOTOR (for Automatic Air Conditioning System) |
| 50. INITIALIZATION SERVO MOTOR (for Manual Air Conditioning System) |