Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM J

2GR-FE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump control ECU assembly (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump control ECU assembly. Based on the signal sent from the ECM, the fuel pump ECU adjust the fuel pump operation speed.

WIRING DIAGRAM

A266397E04
5.938,1.073 6.333,1.302 0.396,0.229 10 false FPC 5.917,4.552 6.365,4.75 0.448,0.198 10 false MREL 3.896,1.083 4.271,1.323 0.375,0.24 10 false FPC 5.646,4.458 5.885,4.635 0.24,0.177 10 false 46 5.948,5.854 6.25,6.031 0.302,0.177 10 false A25 3.052,5.333 4.615,5.583 1.563,0.25 10 false No. 1 Integration Relay 0.979,4.302 2.156,4.521 1.177,0.219 10 false EFI-MAIN NO. 1 3.396,4.875 4.094,5.125 0.698,0.25 10 false EFI MAIN 0.396,2.188 1.125,2.375 0.729,0.188 10 false Fuel Pump 0.396,2.031 0.677,2.177 0.281,0.146 10 false N11 0.823,0.948 1.052,1.188 0.229,0.24 10 false B 0.823,1.635 1.052,1.865 0.229,0.229 10 false E 4,2.417 4.333,2.646 0.333,0.229 10 false +B 2.656,3.125 4.813,3.542 2.156,0.417 10 false Fuel Pump Control ECU Assembly 3.24,2.344 3.375,2.51 0.135,0.167 10 false E 3.24,1.719 3.667,2.021 0.427,0.302 10 false FP- 3.24,0.99 3.594,1.281 0.354,0.292 10 false FP 2.656,4.552 3.083,4.802 0.427,0.25 10 false 1E 4.573,4.552 4.813,4.771 0.24,0.219 10 false 1C 4.615,4.375 4.76,4.542 0.146,0.167 10 false 7 2.698,4.375 2.979,4.635 0.281,0.26 10 false 2 2.698,3.948 2.823,4.104 0.125,0.156 10 false 1 3.021,0.865 3.135,1.01 0.115,0.146 10 false 6 4.302,0.938 4.427,1.094 0.125,0.156 10 false 2 4.302,2.271 4.417,2.427 0.115,0.156 10 false 1 3.021,2.25 3.135,2.396 0.115,0.146 10 false 4 3.021,1.583 3.135,1.729 0.115,0.146 10 false 5 1.052,0.938 1.302,1.188 0.25,0.25 10 false 4 1.052,1.625 1.229,1.802 0.177,0.177 10 false 5 4.615,3.948 4.781,4.104 0.167,0.156 10 false 6 5.646,0.979 5.917,1.177 0.271,0.198 10 false 18 0.74,5.646 1.396,5.906 0.656,0.26 10 false Battery 0.604,4.781 1.26,5.031 0.656,0.25 10 false FL MAIN 6.323,5.854 6.74,6.063 0.417,0.208 10 false ECM 2.646,4.146 2.854,4.292 0.208,0.146 10 false 1B 4.573,4.135 4.875,4.354 0.302,0.219 10 false 1C 2.656,2.979 3.094,3.24 0.438,0.26 10 false N30

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 230

e.

Check whether fuel pump operating sounds can be heard while operating the fuel pump using the tester.

OK:

Operating sounds can be heard from fuel pump.



Result:
Result Proceed to
NG A
OK B



A

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)

B

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP DUTY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL PUMP CONTROL ECU ASSEMBLY)
a.
A256531C01
0.573,1.125 1.031,1.406 0.458,0.281 1.323,1.469 1.271,1.792 false 0.698,1.188 1.198,1.625 0.5,0.438 10 N30 0.542,0.229 1.073,0.594 0.531,0.365 10 *a 1.115,1.802 1.51,2.177 0.396,0.375 10 +B
*a Front view of wire harness connector
(to Fuel Pump Control ECU Assembly)


Disconnect the fuel pump control ECU assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
N30-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)

NG

9.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - BODY GROUND)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - FUEL PUMP)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-6 (FP) - N11-4 (B) Always Below 1 Ω
N30-5 (FP-) - N11-5 (E) Always Below 1 Ω
N30-6 (FP) or N11-4 (B) - Body ground Always 10 kΩ or higher
N30-5 (FP-) or N11-5 (E) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-2 (FPC) - A25-18 (FPC) Always Below 1 Ω
N30-2 (FPC) or A25-18 (FPC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
a.

Replace the fuel pump control ECU assembly.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG

9.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - NO. 1 INTEGRATION RELAY)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-1 (+B) - 1C-6 Always Below 1 Ω
N30-1 (+B) or 1C-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.INSPECT NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)
a.

Inspect the No. 1 integration relay (EFI MAIN relay).

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>INTEGRATION RELAY>INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 INTEGRATION RELAY (EFI MAIN RELAY)

11.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE FUEL PUMP DUTY)
a.
A240046C02
1.927,0.958 2.344,1.677 false 1.521,0.958 1.083,1.677 false 0.125,0.115 0.323,0.281 0.198,0.167 10 *a 2.333,1.708 2.552,1.927 0.219,0.219 10 B 1,1.708 1.24,1.927 0.24,0.219 10 E
*a Component with harness connected
(Fuel Pump)


Remove the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>REMOVAL


b.

Clean the fuel pump to completely remove any remaining fuel.


c.

Connect the fuel pump connector.

CAUTION:

Confirm that no fuel remains inside or on the outside of the fuel pump.



d.

Connect the intelligent tester to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the tester on.


g.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump Duty.

Powertrain > Engine > Active Test
Tester Display
Control the Fuel Pump Duty
50004 234 229

h.

Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tester Operation Specified Condition
4 (B) - 5 (E) Fuel pump control duty: 25% 3.4 to 4.1 V
Fuel pump control duty: 80% 10.0 to 12.5 V



i.

Enter the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump / Speed.


j.

Operate the fuel pump using the active test function and measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Tester Operation Specified Condition
4 (B) - 5 (E) ON (Fuel pump control duty: 90%) 10.2 to 14.0 V


HINT:
·

Be sure to measure the voltage with the all connectors connected.

·

Before performing this inspection, check that the battery voltage is between 11 and 14 V (not depleted).




Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)

NG

14.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
12.CHECK HARNESS AND CONNECTOR (FUEL PUMP CONTROL ECU ASSEMBLY - ECM)
a.

Disconnect the fuel pump control ECU assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N30-2 (FPC) - A25-18 (FPC) Always Below 1 Ω
N30-2 (FPC) or A25-18 (FPC) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE FUEL PUMP
a.

Replace the fuel pump.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
14.REPLACE FUEL PUMP CONTROL ECU ASSEMBLY
a.

Replace the fuel pump control ECU assembly.

Click hereEngine / Hybrid System>2GR-FE FUEL>FUEL PUMP ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
15.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Check the fuel pump operation.

OK:

Malfunction has been repaired successfully.



Result:
Proceed to
OK
NG



OK

END

NG