Home › Engine / Hybrid System › 2GR-FE ENGINE CONTROL › SFI SYSTEM
RM2030EQ _51 Engine / Hybrid System _014634 2GR-FE ENGINE CONTROL _0074393 SFI SYSTEM C

2GR-FE ENGINE CONTROL  SFI SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  P0018  Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A)  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the intake camshaft and camshaft timing oil control valve assembly (for intake camshaft), and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) Deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 1) signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 1)

·

Oil control valve filter (RH)

·

Oil pipe

·

Camshaft timing gear assembly (bank 1)

·

ECM


Comes on (Euro-OBD) / Does not come on (except Euro-OBD) DTC stored
P0018 Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor A) Deviation in the crankshaft position sensor signal and VVT sensor (for intake camshaft of bank 2) signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly (for intake camshaft of bank 2)

·

Oil control valve filter (LH)

·

Oil pipe

·

Camshaft timing gear assembly (bank 2)

·

ECM


Comes on (Euro-OBD) / Does not come on (except Euro-OBD) DTC stored

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM stores DTC P0016 (bank 1) or P0018 (bank 2).

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing gear assembly
Required Sensors/Components (Related) VVT sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 500 to 1000 rpm

CONFIRMATION DRIVING PATTERN

A197314E13
0.161,0.66 1.086,0.809 0.924,0.149 10 Vehicle Speed 1.514,2.102 1.719,2.303 0.205,0.201 10 [A] 2.162,1.659 2.388,1.829 0.225,0.170 10 [B] 3.188,1.648 3.396,1.801 0.208,0.152 10 [C] 3.826,3.013 4.037,3.169 0.211,0.156 10 [D] 4.681,0.853 4.875,1.047 0.194,0.194 10 [E] 5.656,1.617 5.850,1.811 0.194,0.194 10 [F] 6.372,3.021 6.614,3.205 0.243,0.184 10 [G] 0.667,1.753 1.052,1.937 0.385,0.184 10 Idling 4.815,0.256 6.292,0.618 1.477,0.362 10 There is no designated vehicle speed 0.209,2.034 1.138,2.349 0.928,0.316 10 Ignition Switch ON 1.907,2.503 2.698,2.839 0.791,0.336 10 Warming up the engine 2.737,2.524 3.893,2.687 1.156,0.163 10 5 minutes or more 5.266,2.531 6.421,2.694 1.156,0.163 10 5 minutes or more 4.121,2.566 5.020,2.736 0.899,0.170 10 2 to 3 minutes 4.257,1.074 4.6,0.443 4.6,0.443 4.754,0.443 false

1.

Connect the intelligent tester to the DLC3.

2.

Turn the ignition switch to ON and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the ignition switch off and wait for at least 30 seconds.

5.

Turn the ignition switch to ON and turn the tester on [A].

6.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

7.

Idle the engine for 5 minutes or more [C].

8.

Enter the following menus: Powertrain / Engine / DTC [D].

9.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



10.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

11.

Input the DTC: P0016 or P0018.

12.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



13.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


14.

Idle the engine for 5 minutes or more [F].

15.

Enter the following menus: Powertrain / Engine / DTC [G].

16.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



17.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transaxle.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016 OR P0018)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine / DTC.


e.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0016 or P0018 is output A
DTC P0016 or P0018 and other DTCs are output B


HINT:

If any DTCs other than P0016 or P0018 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the intelligent tester to the DLC3.


b.

Start the engine.


c.

Turn the A/C switch on.


d.

Turn the tester on.


e.

Enter the following menus: Powertrain / Engine / Active Test / Control the VVT Linear (Bank 1) or Control the VVT Linear (Bank 2) / All Data / VVT Change Angle #1 or VVT Change Angle #2.

Powertrain > Engine > Active Test
Active Test Display
Control the VVT Linear (Bank1)
Data List Display
VVT Change Angle #1
50004 234 32 305
Powertrain > Engine > Active Test
Active Test Display
Control the VVT Linear (Bank2)
Data List Display
VVT Change Angle #2
50004 234 31 308

f.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.



Result:
Proceed to
OK
NG



OK

3.ADJUST VALVE TIMING

NG

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)
3.ADJUST VALVE TIMING

Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine > Clear DTCs
50002 234

e.

Turn the ignition switch off and wait for at least 30 seconds.


f.

Turn the ignition switch to ON.


g.

Turn the tester on.


h.

Start the engine and warm it up.


i.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


j.

Enter the following menus: Powertrain / Engine / DTC / Pending.


k.

Read the pending DTCs.

Powertrain > Engine > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P0016 or P0018 is output B




A

END

B

5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

OK

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR INTAKE CAMSHAFT)

6.INSPECT OIL CONTROL VALVE FILTER AND OIL PIPE

OK

7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY

NG

REPLACE OIL CONTROL VALVE FILTER AND OIL PIPE

7.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
a.

Inspect the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE MECHANICAL>ENGINE UNIT>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.

Click hereEngine / Hybrid System>2GR-FE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016 OR P0018)

NG

REPLACE CAMSHAFT TIMING GEAR ASSEMBLY