Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P0340  Camshaft Position Sensor Circuit Malfunction  P0342  Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)  P0343  Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)  


DESCRIPTION

The camshaft position sensor for the intake camshaft (VV1 signal) consists of a magnet and MRE (Magneto Resistance Element).

The camshaft has a timing rotor for the camshaft position sensor. When the camshaft rotates, changes occur in the air gaps between the timing rotor and MRE, which affects the magnetic field. As a result, the resistance of the MRE material fluctuates. The camshaft position sensor converts the camshaft rotation data to pulse signals, uses the pulse signals to determine the camshaft angle, and sends it to the ECM. Then the ECM uses this data to control fuel injection duration and injection timing.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0340 Camshaft Position Sensor Circuit Malfunction Either of the following conditions is met (1 trip detection logic):
·

No camshaft position sensor signal to the ECM at an engine speed of 600 rpm or higher.

·

A missing camshaft position sensor signal despite the crankshaft position sensor inputs being normal at an engine speed of 600 rpm or higher.


·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

Intake camshaft

·

Valve timing

·

ECM


Comes on DTC stored
P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) The output voltage of the camshaft position sensor is less than 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

ECM


Comes on DTC stored
P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) The output voltage is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in camshaft position sensor circuit

·

Camshaft position sensor

·

ECM


Comes on DTC stored

A254147E01
2.986,0.993 3.323,1.14 0.337,0.147 10 GND 1.159,1.916 1.903,2.063 0.744,0.147 10 20 ms./DIV. 2.748,0.059 3.284,0.206 0.536,0.147 10 5 V/DIV.

Reference: Inspection using an oscilloscope.

HINT:

The correct waveform is as shown.


ECM Terminal Name Between VV1+ and VV1-
Tester Range 5 V/DIV., 20 ms./DIV.
Condition Idling


MONITOR DESCRIPTION

If no pulse signal is transmitted by the camshaft position sensor despite the camshaft rotating, or the rotation of the camshaft and the crankshaft is not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at less than 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft position sensor
Required Sensors/Components (Related) Crankshaft position sensor
Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on.

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine.

8.

Idle the engine for 10 seconds or more.

9.

Enter the following menus: Powertrain / Engine and ECT / DTC.

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0340, P0342 or P0343.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.




WIRING DIAGRAM

A255253E41
1.083,1.906 1.417,2.052 0.333,0.146 10 false E55 1.083,2.063 4.219,2.26 3.135,0.198 10 false Camshaft Position Sensor (for Intake Camshaft) 5.177,0.417 5.573,0.563 0.396,0.146 10 false VCV1 5.708,2.198 6.031,2.375 0.323,0.177 10 false E28 5.708,2.365 6.052,2.552 0.344,0.188 10 false ECM 4.823,0.417 5.104,0.604 0.281,0.188 10 false 113 4.896,0.958 5.104,1.156 0.208,0.198 10 false 82 4.823,1.49 5.073,1.656 0.25,0.167 10 false 114 2.646,0.365 2.771,0.531 0.125,0.167 10 false 3 2.646,0.896 2.75,1.073 0.104,0.177 10 false 1 2.646,1.448 2.75,1.594 0.104,0.146 10 false 2 2.323,0.375 2.542,0.552 0.219,0.177 10 false VC 2.167,0.906 2.542,1.073 0.375,0.167 10 false VVI+ 2.198,1.438 2.573,1.604 0.375,0.167 10 false VVI- 5.177,0.958 5.552,1.125 0.375,0.167 10 false VV1+ 5.177,1.49 5.552,1.656 0.375,0.167 10 false VV1- 1.615,0.896 1.75,1.063 0.135,0.167 10 false * 0.063,2.375 4.385,2.615 4.323,0.24 10 false *: MRE (Outputs a voltage corresponding to changes in magnetic flux)

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

If no problem is found through this diagnostic troubleshooting procedure, there may be a mechanical problem with the engine.



PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CAMSHAFT POSITION SENSOR)
a.
A194108C17
0.211,0.202 0.397,0.376 0.186,0.174 10 *a 0.364,2.3 0.827,2.586 0.463,0.286 0.443,2.354 0.712,2.495 0.27,0.141 10 E55 2.216,3.107 2.537,3.271 0.321,0.163 10 VC 2.006,2.513 2.287,3.077 false
*a Front view of wire harness connector
(to Camshaft Position Sensor


Disconnect the camshaft position sensor connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E55-3 (VC) - Body ground Power switch on (IG) 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)

NG

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
2.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E55-1 (VVI+) - E28-82 (VV1+) Always Below 1 Ω
E55-2 (VVI-) - E28-114 (VV1-) Always Below 1 Ω
E55-1 (VVI+) or E28-82 (VV1+) - Body ground Always 10 kΩ or higher
E55-2 (VVI-) or E28-114 (VV1-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (CAMSHAFT POSITION SENSOR)
a.
B319222E02
0.469,1.771 0.74,1.969 0.271,0.198 10 OK 2.667,1.771 2.948,1.969 0.281,0.198 10 NG 1.719,1.552 2.396,1.76 0.677,0.208 10 Clearance

Check the camshaft position sensor installation.

OK:

Camshaft position sensor is installed correctly.



Result:
Proceed to
OK
NG



OK

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)

NG

SECURELY REINSTALL CAMSHAFT POSITION SENSOR

4.INSPECT INTAKE CAMSHAFT (TIMING ROTOR)
a.

Check the timing rotor of the intake camshaft.

OK:

Timing rotor does not have any cracks or deformation.


HINT:

Perform "Inspection After Repair" after replacing the intake camshaft.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

NG

5.CHECK VALVE TIMING (CHECK FOR LOOSE TIMING CHAIN AND JUMPED TEETH)

OK

6.REPLACE CAMSHAFT POSITION SENSOR

NG

6.REPLACE CAMSHAFT POSITION SENSOR
a.

Result:
Proceed to
NEXT



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0340, P0342 OR P0343)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the tester on.


h.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

i.

Start the engine.


j.

Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / DTC.


l.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0340, P0342 or P0343 is output A
DTC is not output B


HINT:

If the engine does not start, replace the ECM.




A

B

END

8.CHECK HARNESS AND CONNECTOR (CAMSHAFT POSITION SENSOR - ECM)
a.

Disconnect the camshaft position sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E55-3 (VC) - E28-113 (VCV1) Always Below 1 Ω
E55-3 (VC) or E28-113 (VCV1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR