Refer to DTC P0010 (See page Engine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>P0010).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory |
|---|---|---|---|---|---|
| P0011 | Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1) | Intake valve timing is stuck at a certain value when in the advance range (1 trip detection logic). | ·
Valve timing ·
Camshaft timing oil control valve assembly ·
Oil control valve filter ·
Camshaft timing gear assembly ·
ECM |
Comes on | DTC stored |
| P0012 | Camshaft Position "A" - Timing Over-Retarded (Bank 1) | Intake valve timing is stuck at a certain value when in the retard range (2 trip detection logic). | ·
Valve timing ·
Camshaft timing oil control valve assembly ·
Oil control valve filter ·
Camshaft timing gear assembly ·
ECM |
Comes on | DTC stored |
The ECM optimizes the intake valve timing using the Variable Valve Timing (VVT) system to control the intake camshaft. The VVT system includes the ECM, the camshaft timing oil control valve assembly and the VVT controller (camshaft timing gear assembly). The ECM sends a target duty-cycle control signal to the camshaft timing oil control valve assembly. This control signal regulates the oil pressure supplied to the VVT controller. The VVT controller can advance or retard the intake camshaft.
If the difference between the target and actual intake valve timing is large, and changes in the actual intake valve timing are small, the ECM interprets this as a VVT controller stuck malfunction and stores a DTC.
Example:
A DTC is stored when the following conditions "A" and "B" are met:
It takes 5 seconds or more to change the valve timing by 5°CA (Condition "A").
After the above condition is met, the camshaft timing oil control valve assembly is forcibly activated for 10 seconds (Condition "B").
DTC P0011 (Advanced Cam Timing) is subject to 1 trip detection logic.
DTC P0012 (Retarded Cam Timing) is subject to 2 trip detection logic.
These DTCs indicate that the VVT controller cannot operate properly due to a camshaft timing oil control valve assembly malfunction or the presence of foreign objects in the camshaft timing oil control valve assembly.
| Required Sensors/Components (Main) | Camshaft timing oil control valve assembly
Camshaft timing gear assembly |
| Required Sensors/Components (Related) | Crankshaft position sensor
Camshaft position sensor Engine coolant temperature sensor |
| Frequency of Operation | Continuous |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG) and turn the tester on.
Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).
P0011 is output:
Clear the DTC without using the tester.
P0012 is output:
Clear the DTC with using the tester.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on [A].
Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].
Accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for 10 seconds or more [C].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
If the engine stops, further depress the accelerator pedal to restart the engine.
Idle the engine for 100 seconds or more [D].
Enter the following menus: Powertrain / Engine and ECT / DTC [E].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0011 or P0012.
Check the DTC judgment result.
| Tester Display | Description |
|---|---|
| NORMAL | ·
DTC judgment completed ·
System normal |
| ABNORMAL | ·
DTC judgment completed ·
System abnormal |
| INCOMPLETE | ·
DTC judgment not completed ·
Perform driving pattern after confirming DTC enabling conditions |
| N/A | ·
Unable to perform DTC judgment ·
Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit |
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
If the judgment result shows INCOMPLETE or N/A, perform steps [F] through [H].
Accelerate the vehicle to 60 km/h (37 mph) or more by depressing the accelerator pedal for 10 seconds or more [F].
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Idle the engine for 100 seconds or more [G].
Enter the following menus: Powertrain / Engine and ECT / DTC [H].
Read the pending DTCs.
If a pending DTC is output, the system is malfunctioning.
If a pending DTC is not output, perform the following procedure.
Check the DTC judgment result again.
If the judgment result shows NORMAL, the system is normal.
If the judgment result shows ABNORMAL, the system has a malfunction.
Refer to DTC P0010 (See page Engine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>P0010).
DTC P0011 or P0012 may be stored when foreign objects in the engine oil are caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. Those foreign objects may then be captured by the oil filter.
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC P0011 or P0012 is output | A |
| DTC P0011 or P0012 and other DTCs are output | B |
If any DTCs other than P0011 or P0012 are output, troubleshoot those DTCs first.
A
B
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1).
| Tester Display |
|---|
| Control the VVT Linear (Bank1) |
Check the engine speed while operating the camshaft timing oil control valve assembly (for intake camshaft) using the tester.
| Tester Operation | Specified Condition |
|---|---|
| 0% | Normal engine speed |
| 100% | Engine idles roughly or stalls |
Refer to "Data List / Active Test" [VVT OCV Duty #1 and VVT Change Angle #1].
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DATA LIST / ACTIVE TEST
If the result is not acceptable, cool the engine (engine coolant temperature is 50°C (122°F) or less) and perform the Active Test again.
Test not possible with the shift lever in P during charge control. Move the shift lever to N to perform test.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
P0011 is output:
Clear the DTC without using the tester.
P0012 is output:
Clear the DTC with the tester.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P0011 or P0012 is output | B |
DTC P0011 or P0012 may be stored when foreign objects in the engine oil is caught in some parts of the system. The DTC will remain stored even if the system returns to normal after a short time. These foreign objects may then be captured by the oil filter.
A
B
| *1 | Timing Mark | - | - |
Remove the cylinder head cover sub-assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY
Turn the crankshaft pulley and align its groove with the "0" timing mark of the timing chain cover.
Check that the timing marks of the camshaft timing gear assembly and camshaft timing exhaust gear assembly are at the positions shown in the illustration.
If the timing marks are not as shown, turn the crankshaft one revolution clockwise.
Timing marks on camshaft timing gear assembly and camshaft timing sprocket are aligned as shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the camshaft timing oil control valve assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the oil control valve filter.
Click hereEngine / Hybrid System>2AR-FXE ENGINE MECHANICAL>ENGINE UNIT>DISASSEMBLY
Check that the oil control valve filter is not clogged.
Oil control valve filter is not clogged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the camshaft timing gear assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE MECHANICAL>CAMSHAFT>REMOVAL
Perform "Inspection After Repair" after replacing the camshaft timing gear assembly.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs.
Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR
P0011 is output:
Clear the DTC without using the tester.
P0012 is output:
Clear the DTC with using the tester.
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the tester on.
Put the engine in inspection mode (maintenance mode).
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE
| Tester Display |
|---|
| Inspection Mode |
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
Read the pending DTCs.
| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTC P0011 or P0012 is output | B |
A
B