Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM C

2AR-FXE ENGINE CONTROL  SFI SYSTEM  P0016  Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A)  


DESCRIPTION

In the VVT (Variable Valve Timing) system, the appropriate intake valve open and close timing is controlled by the ECM. The ECM performs intake valve control by performing the following: 1) controlling the camshaft and camshaft timing oil control valve assembly, and operating the camshaft timing gear assembly; and 2) changing the relative positions of the camshaft and crankshaft.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0016 Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor A) Deviation in crankshaft position sensor signal and camshaft position sensor signal (2 trip detection logic).
·

Valve timing

·

Camshaft timing oil control valve assembly

·

Oil control valve filter

·

Camshaft timing gear assembly

·

ECM


Comes on DTC stored

MONITOR DESCRIPTION

To monitor the correlation of the intake camshaft position and crankshaft position, the ECM checks the VVT learned value while the engine is idling. The VVT learned value is calibrated based on the camshaft position and crankshaft position. The intake valve timing is set to the most retarded angle while the engine is idling. If the VVT learned value is out of the specified range in consecutive driving cycles, the ECM illuminates the MIL and stores a DTC.

MONITOR STRATEGY

Required Sensors/Components (Main) Camshaft timing gear assembly
Required Sensors/Components (Related) Camshaft position sensor
Crankshaft position sensor
Frequency of Operation Continuous

TYPICAL ENABLING CONDITIONS

Engine speed 900 to 1100 rpm

CONFIRMATION DRIVING PATTERN

A197314E69
4.26,1.115 4.604,0.49 4.604,0.49 4.75,0.49 false 0.156,0.656 1.094,1.021 0.938,0.365 10 false Vehicle Speed 1.51,2.104 1.979,2.417 0.469,0.313 10 false [A] 2.167,1.656 2.594,1.958 0.427,0.302 10 false [B] 3.188,1.646 3.729,1.948 0.542,0.302 10 false [C] 3.823,3.01 4.594,3.479 0.771,0.469 10 false [D] 4.521,1.146 5,1.5 0.479,0.354 10 false [E] 5.656,1.615 6.115,1.906 0.458,0.292 10 false [F] 6.375,3.021 6.844,3.427 0.469,0.406 10 false [G] 0.719,1.75 1.104,1.938 0.385,0.188 10 false Idling 4.813,0.417 6.292,0.781 1.479,0.365 10 false There is no designated vehicle speed 0.208,2.031 1.167,2.531 0.958,0.5 10 false Power Switch on (IG) 1.906,2.573 2.698,2.906 0.792,0.333 10 false Warming up the engine 2.74,2.521 3.896,2.688 1.156,0.167 10 false 5 minutes or more 5.271,2.531 6.5,2.927 1.229,0.396 10 false 5 minutes or more 4.125,2.563 5.021,2.729 0.896,0.167 10 false 2 to 3 minutes

1.

Connect the intelligent tester to the DLC3.

2.

Turn the power switch on (IG) and turn the tester on.

3.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

4.

Turn the power switch off and wait for at least 30 seconds.

5.

Turn the power switch on (IG) and turn the tester on [A].

6.

Put the engine in inspection mode (maintenance mode) (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).

7.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher [B].

8.

Idle the engine for 5 minutes or more [C].

9.

Enter the following menus: Powertrain / Engine and ECT / DTC [D].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0016.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.

·

If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].



14.

Drive the vehicle for 2 to 3 minutes [E].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


15.

Idle the engine for 5 minutes or more [F].

16.

Enter the following menus: Powertrain / Engine and ECT / DTC [G].

17.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



18.

Check the DTC judgment result.

HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




CAUTION / NOTICE / HINT

HINT:
·

The monitor for this DTC detects when the timing chain is shifted by 2 to 3 teeth or more.

·

Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0016)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Enter the following menus: Powertrain / Engine and ECT / DTC.


e.

Read the DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC P0016 is output A
DTC P0016 and other DTCs are output B


HINT:

If any DTCs other than P0016 are output, troubleshoot those DTCs first.




A

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)

B

2.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (CONTROL THE VVT LINEAR)
HINT:

If the VVT system can be operated through the Active Test, it can be assumed that the VVT system is operating normally.


a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

d.

Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.


e.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Linear (Bank 1) / All Data / VVT Change Angle #1.

Powertrain > Engine and ECT > Active Test
Active Test Display
Control the VVT Linear (Bank1)
Data List Display
VVT Change Angle #1
50004 234 32 305

f.

Perform the Active Test. Check that the displacement angle varies.

OK:

Displacement angle varies.


HINT:

Test not possible with the shift lever in P during charge control. Move the shift lever to N to perform test.



Result:
Proceed to
OK
NG



OK

3.ADJUST VALVE TIMING

NG

4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
3.ADJUST VALVE TIMING
a.

Adjust the valve timing.

Click hereEngine / Hybrid System>2AR-FXE ENGINE MECHANICAL>ENGINE UNIT>REASSEMBLY

Result:
Proceed to
NEXT




NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
4.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>CAMSHAFT OIL CONTROL VALVE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.INSPECT OIL CONTROL VALVE FILTER

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

5.INSPECT OIL CONTROL VALVE FILTER

OK

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NG

6.REPLACE CAMSHAFT TIMING GEAR ASSEMBLY

NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0016)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the tester on.


d.

Clear the DTCs.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>DTC CHECK / CLEAR

Powertrain > Engine and ECT > Clear DTCs
50002 234

e.

Turn the power switch off and wait for at least 30 seconds.


f.

Turn the power switch on (IG).


g.

Turn the tester on.


h.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

i.

Start the engine and warm it up.


j.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


k.

Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.


l.

Read the pending DTCs.

Powertrain > Engine and ECT > Trouble Codes
50001 234
Result:
Result Proceed to
DTC is not output A
DTC P0016 is output B




A

END

B