Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB BOLT
RM2040EQ _52 Drivetrain _014703 AXLE AND DIFFERENTIAL _0074957 FRONT AXLE HUB BOLT A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB BOLT  REPLACEMENT  


CAUTION / NOTICE / HINT

NOTICE:

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55702A 3.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 4. DISABLE BRAKE CONTROL

Hide 5.REMOVE FRONT WHEEL

Hide 6.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Remove the 2 bolts and separate the front disc brake caliper assembly.

NOTICE:

Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging down by the front flexible hose.



Hide 43512 7.REMOVE FRONT DISC

Hide 43502D 8.REMOVE FRONT AXLE HUB BOLT

a.
C238962

Position the front axle hub bolt to be removed as shown in the illustration.


b.
C239298C01
2.104,0.927 2.104,0.583 2.104,0.583 2.833,0.313 false 2.448,1.104 2.448,0.458 false 1.552,1.292 1.125,1.292 false 0.844,1.208 1.208,1.438 0.365,0.229 10 false SST 2.885,0.24 3.115,0.479 0.229,0.24 10 false *1
*1 Nut


Temporarily install 2 nuts to the front axle hub bolts as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the nuts to prevent damage to the front axle hub bolts.



c.

Using SST and a screwdriver or an equivalent tool to hold the front axle hub, remove the front axle hub bolt.

SST
09628-10011  


Hide 43502D 9.INSTALL FRONT AXLE HUB BOLT

a.
C238962

Position a new front axle hub bolt as shown in the illustration.


b.

Temporarily install the front axle hub bolt to the front axle hub.


c.
C239299C01
0.656,0.969 0.656,1.552 false 0.958,1.302 0.958,0.823 false 0.896,1.323 1.208,1.479 0.313,0.156 10 false *1 0.583,1.573 0.896,1.729 0.313,0.156 10 false *2
*1 Nut
*2 Washer


Install a washer and nut to the front axle hub bolt as shown in the illustration.

Recommended service nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



d.

Using a screwdriver or an equivalent tool to hold the front axle hub, install the front axle hub bolt by tightening the nut.

NOTICE:
·

Install the nuts to prevent damage to the front axle hub bolts.

·

Do not damage the threads of the front axle hub bolts.




e.

Remove the 3 nuts and washer from the 3 front axle hub bolts.


Hide 43512 10.INSTALL FRONT DISC

Hide 11.INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY

a.

Install the front disc brake caliper assembly to the steering knuckle with the 2 bolts.

Torque:
107 N*m (1090 kgf*cm, 79 ft.*lbf)

NOTICE:

Do not twist the flexible hose when installing the front disc brake caliper assembly.



Hide 12.INSTALL FRONT WHEEL

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 13.CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

a.

Connect the cable to the negative (-) auxiliary battery terminal.

Click herePower Source / Network>2AR-FXE BATTERY / CHARGING>AUXILIARY BATTERY>INSTALLATION


b.

Connect the reservoir level switch connector.



Hide 55702A 14.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 15.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY