Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB
RM2040EQ _52 Drivetrain _014703 AXLE AND DIFFERENTIAL _0074958 FRONT AXLE HUB A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB  REMOVAL  


CAUTION / NOTICE / HINT

NOTICE:

When the brake pedal is first depressed after replacing the brake pads or pushing back the disc brake piston, DTC C1214 may be output. As there is no malfunction, clear the DTC.


HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal, Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


Hide 2.REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

Hide 55702A 3.REMOVE FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 4. DISABLE BRAKE CONTROL

Hide 5.REMOVE FRONT WHEEL

Hide 89543 7.SEPARATE FRONT SPEED SENSOR

a.
C238961

Remove the bolt, disengage the clamp and separate the front speed sensor and front flexible hose.

NOTICE:

Be sure to separate the front speed sensor from the front shock absorber assembly completely.



b.
C238448

Remove the bolt and front speed sensor from the steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.




Hide 8.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 9.REMOVE FRONT DISC

Hide 45470 10.SEPARATE TIE ROD ASSEMBLY

Hide 43420 11.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

a.
C238968C06
2.875,0.646 2.604,0.646 2.604,0.646 2.604,1.656 false 3.042,1 2.604,1 false 2.521,1.646 2.823,1.927 0.302,0.281 10 false *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


b.

Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

If it is difficult to separate, tap the end of the front drive shaft assembly using a brass bar and a hammer.


Hide 48069 12.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

a.
C238969

Remove the bolt and 2 nuts, and separate the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.


Hide 13.REMOVE FRONT AXLE ASSEMBLY

a.
C238980

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:
·

When removing the nuts, keep the bolts from rotating.

·

Be careful not to damage the drive shaft boot or speed sensor rotor.




Hide 43246B 14.REMOVE FRONT NO. 1 WHEEL BEARING DUST DEFLECTOR

a.
C238978C04
1.948,0.99 2.615,0.99 false 2.646,0.896 2.906,1.135 0.26,0.24 10 false *1
*1 Vinyl Tape


Using a screwdriver with its tip wrapped with vinyl tape, remove the front No. 1 wheel bearing dust deflector.

NOTICE:

Be careful not to damage the steering knuckle.



Hide 43502G 15.REMOVE FRONT AXLE HUB HOLE SNAP RING

a.
C238979

Using snap ring pliers, remove the front axle hub hole snap ring.


Hide 43502C 16.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C238975N05
2.125,2.385 2.125,2.75 false 1.771,0.521 1.771,0.292 1.771,0.292 2.167,0.292 false 1.99,2.771 2.458,3.073 0.469,0.302 10 false SST 2.208,0.219 2.708,0.51 0.5,0.292 10 false SST

Hold the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Using SST, remove the front axle hub sub-assembly.

SST
09520-00031  


c.
C167711N03
1.073,2.073 0.49,1.521 0.49,1.521 0.74,2.167 false 0.51,1.531 1.094,1.698 false 2.385,1.042 2.156,0.625 2.156,0.625 2.458,0.625 false 2.885,1.333 2.885,0.635 2.885,0.635 2.969,0.635 false 0.188,1.438 0.729,1.75 0.542,0.313 10 false SST 1.865,0.552 2.375,0.865 0.51,0.313 10 false SST 3.01,0.563 3.396,0.844 0.385,0.281 10 false SST

Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.

SST
09555-55010  
09950-60010  (09951-00440)
09950-70010  (09951-07100)

NOTICE:

Be careful not to drop the front axle hub sub-assembly.



Hide 47782 17.REMOVE FRONT DISC BRAKE DUST COVER

a.
C238976

Remove the 4 bolts and front disc brake dust cover from the steering knuckle.


Hide 43502E 18.REMOVE FRONT AXLE HUB BEARING

a.
C202363C08
2.583,1.531 2.583,1.833 false 2.438,1.313 2.229,0.969 2.229,0.969 2.479,0.969 false 0.885,3.219 0.885,3.313 0.885,3.313 1.979,3.313 false 1.729,2.979 1.729,3.313 false 0.813,1.948 0.521,1.625 0.521,1.625 0.906,1.625 false 0.354,2.448 0.354,3 false 2.438,1.854 2.885,2.135 0.448,0.281 10 false SST 1.938,0.875 2.417,1.177 0.479,0.302 10 false SST 2,3.229 2.24,3.427 0.24,0.198 10 false *2 0.229,1.542 0.635,1.802 0.406,0.26 10 false SST 0.26,3.021 0.5,3.271 0.24,0.25 10 false *1
*1 Steel Plate
*2 V-block


Place the bearing inner race (outside) on the front axle hub bearing.


b.

Using SST, a steel plate, V-blocks and a press, remove the front axle hub bearing from the steering knuckle.

SST
09950-60010  (09951-00440, 09952-06010)
09950-60020  (09951-00750)
09950-70010  (09951-07100)

NOTICE:

Keep the steering knuckle level.