Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE BOOSTER PUMP
RM2040EQ _54 Brake _014709 BRAKE SYSTEM (OTHER) _0074989 BRAKE BOOSTER PUMP A

BRAKE SYSTEM (OTHER)  BRAKE BOOSTER PUMP  INSTALLATION  


PROCEDURE

Hide 44590 1.INSTALL BRAKE ACTUATOR BRACKET ASSEMBLY

a.
C243039C02
0.99,0.927 0.469,0.927 true 0.313,0.833 0.594,1.094 0.281,0.26 10 false *a 1.896,1.031 2.156,1.271 0.26,0.24 9 false 1 0.927,2.813 1.125,3.01 0.198,0.198 9 false 2 0.365,2.792 0.583,3 0.219,0.208 9 false 3
*a Claw


Engage the claw to set the brake actuator bracket assembly to the vehicle body.


b.

Install the 3 bolts to secure the brake actuator bracket assembly to the vehicle body.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:

Tighten the 3 bolts in the order shown in the illustration.



c.

Engage the clamp to install the front No. 5 brake tube to the brake actuator bracket assembly.


d.

Engage the 2 clamps to install the 2 wire harnesses to the brake actuator bracket assembly.


Hide 2.INSTALL FRONT WHEEL LH

Torque:
103 N*m (1049 kgf*cm, 76 ft.*lbf)

Hide 47070 3.INSTALL BRAKE BOOSTER PUMP ASSEMBLY

a.

Insert the 2 studs of the brake booster pump assembly to the 2 holes of the brake actuator bracket assembly, and insert the pin of the brake actuator bracket assembly to the brake booster pump bushing.

C264316C01
4.885,0.854 4.438,0.854 false 4.979,1.417 4.688,2.167 4.688,2.167 5.24,1.385 false 5.542,2 6.177,2.083 6.177,2.083 6.01,1.74 false 1.979,0.865 1.219,0.865 true 2.042,0.875 2.521,0.875 true 2.021,0.958 2.021,1.146 2.021,1.146 2.177,1.146 true 4.271,0.802 4.583,0.958 0.313,0.156 10 *1 4.531,2.115 4.844,2.271 0.313,0.156 10 *2 6.219,2.031 6.531,2.188 0.313,0.156 10 *3 2.563,0.823 2.875,0.979 0.313,0.156 10 *4 1.073,0.813 1.385,0.969 0.313,0.156 10 *5 2.219,1.094 2.531,1.25 0.313,0.156 10 *6
*1 Union *2 Connector
*3 Stud *4 Pin
*5 Brake Booster Pump Bushing *6 Brake Booster Pump Collar


NOTICE:
·

Do not carry the brake booster pump assembly by the parts shown in bold (*1, *2 and *3) in the illustration.

·

Do not drop the brake booster pump assembly when carrying it.

·

Do not kink or damage the brake lines.

·

Be careful not to allow any brake fluid to enter the connector.

·

When installing the brake booster pump assembly to the brake actuator bracket assembly, confirm that the brake booster pump collar and brake booster pump bushing are installed on the brake booster pump assembly.

·

If installing a new brake booster pump assembly, do not remove the hole plug before connecting the brake lines because the brake booster pump assembly is filled with brake fluid.




b.

Install the 2 brake actuator case collars, 2 brake booster pump bushings and 2 nuts to the brake actuator bracket assembly.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


c.

Using a union nut wrench, connect the front No. 1 brake tube to the brake booster pump assembly.

Torque:
15 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION



d.

Connect the 2 connectors to the brake booster pump assembly.


Hide 47233 4.INSTALL RESERVOIR BRACKET

a.
C243030C02
0.781,1.25 0.781,1.427 0.781,1.427 0.979,1.427 false 0.99,1.323 1.229,1.563 0.24,0.24 10 false *a
*a Claw


Engage the claw to set the reservoir bracket to the brake actuator bracket assembly.


b.

Install the 2 bolts to secure the reservoir bracket to the brake actuator bracket assembly.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 44571A 5.CONNECT NO. 1 BRAKE ACTUATOR HOSE

a.
C243058C02
1.125,0.396 1.448,0.688 0.323,0.292 10 false 30° 0.802,0.396 1.104,0.656 0.302,0.26 10 false 30°
V100136

Up


Connect the No. 1 brake actuator hose to the brake booster pump assembly with the clip.

NOTICE:
·

When connecting the No. 1 brake actuator hose, face the identification mark up.

·

Match the identification mark of the No. 1 brake actuator hose and the rib of the brake booster pump assembly.

·

Make sure to install the hose to the proper location.

·

Install the clip within the range shown in the illustration.




Hide 47238C 6.BLEED RESERVOIR TUBE

Hide 47238C 7.INSTALL RESERVOIR TUBE

Hide 47220D 8.INSTALL BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

Hide 9.FILL RESERVOIR WITH BRAKE FLUID

Hide 10.CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

Hide 11.BLEED BRAKE SYSTEM

Hide 12.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17801 13.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 14.INSTALL AIR CLEANER CAP SUB-ASSEMBLY

Hide 17750A 15.INSTALL INLET AIR CLEANER ASSEMBLY

Hide 53295E 16.INSTALL COOL AIR INTAKE DUCT SEAL

Hide 55702A 17.INSTALL FRONT OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 18.INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY