This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication do not match.
When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2285 | Steering Lock Position Signal Circuit Malfunction | The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match. | ·
AM2 fuse ·
Steering lock ECU (steering lock actuator assembly) ·
Power management control ECU ·
Wire harness or connector |
DTC Output Confirmation Operation
Disconnect the cable from the negative (-) auxiliary battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) auxiliary battery terminal. Wait 40 seconds or more with the power switch off (with the steering wheel locked), then turn the power switch on (ACC) (with the steering unlocked) and wait 40 seconds or more. |
*: Only detected while a malfunction is present and the power switch is on (IG)
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The hybrid control system cannot be started. | The ECU does not send an hybrid control system start request. |
When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:
for Power Source Control: Body / Power Source Control / DTC.
for Entry&Start: Body / Entry&Start / DTC.
The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.
Before replacing the steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).
Before replacing the power management control ECU, refer to the Service Bulletin.
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.
| DTC | Data List Item | Active Test Item |
|---|---|---|
| B2285 | Power Source Control
Steering Unlock Switch Entry&Start
·
Power Supply Short ·
Motor Driver Short ·
Lock Bar Stuck Error |
- |
Check for DTCs.
Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR
LIN communication system DTC B2785 is not output simultaneously.
If the steering wheel cannot be locked or unlocked, the power switch cannot be turned on (IG) and the hybrid control system cannot be started.
If LIN communication is not available, the steering wheel cannot be locked or unlocked.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Power Source Control / Data List.
According to the display on the intelligent tester, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Steering Unlock Switch | Switch State of steering unlock sensor signal output from steering lock actuator assembly | ON or OFF | ON: Steering unlocked
OFF: Steering locked |
·
When the shift lever is in P and the power switch is off, if any door is opened or closed, the steering is locked. ·
When the electrical key transmitter sub-assembly is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks. ·
The hybrid control system cannot be started when the steering unlock signal is off. |
| Tester Display |
|---|
| Steering Unlock Switch |
| Result | Proceed to |
|---|---|
| Data List item does not change | A |
| Data List item changes | B |
A
B
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected(Steering Lock ECU (Steering Lock Actuator Assembly)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Positive (+) tester probe → I24-4 (SLP1)
Negative (-) tester probe → Body ground |
Steering locked* | 10 kΩ or higher |
| Steering unlocked* | Below 1 Ω |
*: If any of the doors are opened then closed with the shift lever in P and the power switch off, the steering wheel will be locked. If the power switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.
DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the power management control ECU individually.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the I4 connector from the power management control ECU.
Disconnect the I24 connector from the steering lock ECU (steering lock actuator assembly).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I4-16 (SLP) - I24-4 (SLP1) | Always | Below 1 Ω |
| I4-16 (SLP) or I24-4 (SLP1) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG