Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  C1271/71  Low Output Signal of Front Speed Sensor RH (Test Mode DTC)  C1272/72  Low Output Signal of Front Speed Sensor LH (Test Mode DTC)  C1464/31  Front Speed Sensor RH Circuit  C1465/32  Front Speed Sensor LH Circuit  


DESCRIPTION

Each speed sensor detects wheel speed and sends signals to the skid control ECU. These signals are used for ABS control.

DTCs C1271/71 and C1272/72 can be cleared when the speed sensor sends a wheel speed signal or when Test Mode ends. DTCs C1271/71 and C1272/72 are output only in Test Mode.

C172023E10
5.21,1.818 5.988,1.986 0.778,0.168 10 High speed 4.267,1.818 4.973,1.970 0.705,0.152 10 Low speed 6.295,1.378 6.685,1.546 0.391,0.168 10 0.7 V 6.295,1.013 6.685,1.181 0.391,0.168 10 1.4 V 0.413,0.161 1.344,0.362 0.930,0.201 10 Speed Sensor 1.039,2.104 2.332,2.305 1.293,0.201 10 Speed Sensor Rotor 1.503,0.802 1.503,0.27 1.503,0.27 1.366,0.27 false

DTC No. Detection Item INF Code DTC Detection Condition Trouble Area Note
C1271/71 Low Output Signal of Front Speed Sensor RH (Test Mode DTC) - Detected only during Test Mode.
·

Front speed sensor RH

·

Sensor installation

·

Front speed sensor rotor RH (Front drive outboard joint shaft RH)


ABS Test Mode DTC
C1272/72 Low Output Signal of Front Speed Sensor LH (Test Mode DTC) - Detected only during Test Mode.
·

Front speed sensor LH

·

Sensor installation

·

Front speed sensor rotor LH (Front drive outboard joint shaft LH)


ABS Test Mode DTC
C1464/31 Front Speed Sensor RH Circuit 501
502
503
504
506
507
508
·

INF Code: 501

·

While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 502

·

A malfunction occurs in 2 or more wheels.



·

INF Code: 503

·

An open is detected in the speed sensor signal circuit for 0.05 seconds or more.



·

INF Code: 504

·

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 506

·

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 507

·

While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 508

·

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 501, 502, 504, 507

·

Open or short in speed sensor


·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


·

Open or short in wire harness


·

Improperly connected connector, deformation or corrosion of terminals


·

Front speed sensor RH


·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 503

·

Open or short in speed sensor


·

Open or short in wire harness


·

Improperly connected connector, deformation or corrosion of terminals


·

Front speed sensor RH


·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 506, 508

·

Open or short in wire harness


·

Skid control ECU (Brake booster with master cylinder assembly)



ABS DTC
C1465/32 Front Speed Sensor LH Circuit 511
512
513
514
516
517
518
·

INF Code: 511

·

While driving at 10 km/h (6 mph) or more, speed sensor output from one or two wheels is lower than that from other wheels for 15 seconds or more.



·

INF Code: 512

·

A malfunction occurs in 2 or more wheels.



·

INF Code: 513

·

An open is detected in the speed sensor signal circuit for 0.05 seconds or more.



·

INF Code: 514

·

Instantaneous interruption of sensor signal from the malfunctioning wheel occurs 255 times or more.



·

INF Code: 516

·

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 0.5 seconds or more.



·

INF Code: 517

·

While driving at 10 km/h (6 mph) or more, speed sensor output from one wheel is 0 km/h (0 mph) for 1 second or more.



·

INF Code: 518

·

When VM1 voltage is 8.6 V or more, sensor supply voltage drops for 60 seconds or more.



·

INF Code: 511, 512, 514, 517

·

Open or short in speed sensor


·

Improperly installed speed sensor, or abnormal clearance between sensor and rotor


·

Open or short in wire harness


·

Improperly connected connector, deformation or corrosion of terminals


·

Front speed sensor LH


·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 513

·

Open or short in speed sensor


·

Open or short in wire harness


·

Improperly connected connector, deformation or corrosion of terminals


·

Front speed sensor LH


·

Skid control ECU (Brake booster with master cylinder assembly)



·

INF Code: 516, 518

·

Open or short in wire harness


·

Skid control ECU (Brake booster with master cylinder assembly)



ABS DTC

HINT:
·

DTCs C1464/31 and C1271/71 are for the front speed sensor RH.

·

DTCs C1465/32 and C1272/72 are for the front speed sensor LH.



WIRING DIAGRAM

C269757E05
1.188,1.458 2.802,1.729 1.615,0.271 10 false Front Speed Sensor RH 1.396,1 1.583,1.25 0.188,0.25 10 false 1 2.313,1 2.427,1.167 0.115,0.167 10 false 2 1.115,3.438 2.635,3.604 1.521,0.167 10 false Front Speed Sensor LH 1.396,2.979 1.51,3.146 0.115,0.167 10 false 1 2.302,2.979 2.417,3.146 0.115,0.167 10 false 2 5,4 7.104,4.5 2.104,0.5 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 5.781,0.99 6.042,1.354 0.26,0.365 10 false 5 5.99,0.542 6.469,0.875 0.479,0.333 10 false FR+ 5.708,0.427 6,0.729 0.292,0.302 10 false 18 5.99,1.115 6.375,1.354 0.385,0.24 10 false FR- 5.708,2.969 6.125,3.323 0.417,0.354 10 false 32 5.99,2.5 6.448,2.802 0.458,0.302 10 false FL+ 5.708,2.417 6.083,2.708 0.375,0.292 10 false 31 5.99,3.063 6.323,3.26 0.333,0.198 10 false FL- 1.188,1.313 1.583,1.51 0.396,0.198 10 false A53 1.115,3.281 1.583,3.583 0.469,0.302 10 false A16 3.771,1.49 4.438,1.656 0.667,0.167 10 false Shielded 3.76,3.49 4.427,3.656 0.667,0.167 10 false Shielded 5,3.844 5.719,4.219 0.719,0.375 10 false A28 1.552,3.073 2.063,3.292 0.51,0.219 10 false FL+ 2,3.073 2.5,3.313 0.5,0.24 10 false FL- 1.552,1.104 2.021,1.344 0.469,0.24 10 false FR+ 2,1.104 2.375,1.385 0.375,0.281 10 false FR-

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION)
a.

Using the intelligent tester, check for any momentary interruptions in the wire harness and connector corresponding to a DTC.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>CHECK FOR INTERMITTENT PROBLEMS

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Speed Open Front speed sensor RH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
FL Speed Open Front speed sensor LH open detection Error or Normal Error: Momentary interruption
Normal: Normal
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Speed Open
FL Speed Open
50003 105 200,201
OK:

There are no momentary interruptions.


HINT:

Perform the above inspection before removing the sensor and connector.



Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.READ VALUE USING INTELLIGENT TESTER (FRONT SPEED SENSOR)
a.

Select the Data List on the intelligent tester.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DATA LIST / ACTIVE TEST

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front speed sensor RH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front speed sensor LH Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) Vehicle stopped: 0 km/h (0 mph) When driving at constant speed: No large fluctuations
Chassis > ABS/VSC/TRC > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
50003 105 1,2

b.

Check the speed value output from the speed sensor displayed on the intelligent tester.

HINT:

Factors that affect the indicated vehicle speed include tire size, tire inflation, and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, see the reference chart.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>ON-VEHICLE INSPECTION


OK:

The speed value output from the speed sensor displayed on the intelligent tester is similar to the speed indicated on the speedometer.



Result:
Proceed to
OK
NG



OK

3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
3.PERFORM TEST MODE INSPECTION (SIGNAL CHECK)
a.

Turn the power switch off.


b.

Perform the sensor check in the Test Mode Procedure.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 3
OK:

All Test Mode DTCs are cleared.



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

5.CHECK FRONT SPEED SENSOR INSTALLATION
4.RECONFIRM DTC
a.

Turn the power switch off.


b.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

c.

Turn the power switch on (READY).


d.

Perform a road test.


e.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1464/31 and C1465/32 are not output. A
DTCs C1464/31 and/or C1465/32 are output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

B

10.REPLACE FRONT SPEED SENSOR
5.CHECK FRONT SPEED SENSOR INSTALLATION
a.
C144929C04
0.833,1.625 0.833,0.667 0.833,0.667 1,0.667 false 0.708,2.49 1,2.865 1,2.865 1.177,2.865 false 0.49,2.979 0.771,3.177 0.281,0.198 10 *c 2.677,2.969 3,3.167 0.323,0.198 10 *d 1.25,2.781 2.167,2.979 0.917,0.198 10 *b 1.031,0.573 1.573,0.771 0.542,0.198 10 *a 0.25,0.167 1.698,0.365 1.448,0.198 10 *1
*1 Front Speed Sensor
*a 8.5 Nm
*b No clearance
*c OK
*d NG


Turn the power switch off.


b.

Check the speed sensor installation.

OK:

There is no clearance between the sensor and the front steering knuckle.

The installation bolt is tightened properly.



Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR TIP

NG

6.CHECK FRONT SPEED SENSOR TIP

b.

Check the speed sensor tip.

OK:

The sensor tip is free of scratches, oil, and foreign matter.


NOTICE:

Check the speed sensor signal after cleaning or replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)

NG

CLEAN OR REPLACE FRONT SPEED SENSOR

7.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR)
a.

Install the front speed sensor.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A28 skid control ECU (brake booster withmaster cylinder assembly) connector and the A53 or A16 front speed sensor connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RH
Tester Connection Condition Specified Condition
A28-18 (FR+) - A53-1 (FR+) Always Below 1 Ω
A28-18 (FR+) - Body ground Always 10 kΩ or higher
A28-5 (FR-) - A53-2 (FR-) Always Below 1 Ω
A28-5 (FR-) - Body ground Always 10 kΩ or higher

for LH
Tester Connection Condition Specified Condition
A28-31 (FL+) - A16-1 (FL+) Always Below 1 Ω
A28-31 (FL+) - Body ground Always 10 kΩ or higher
A28-32 (FL-) - A16-2 (FL-) Always Below 1 Ω
A28-32 (FL-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT SKID CONTROL ECU (SENSOR OUTPUT)
a.
C248346C07
0.177,1.219 0.615,1.51 0.438,0.292 1.76,1.219 2.198,1.51 0.438,0.292 2.604,1.948 3.115,2.729 false 1.188,1.958 1.708,2.729 false 0.146,0.177 0.865,0.927 0.719,0.75 10 false *a 1.552,2.76 1.844,2.917 0.292,0.156 10 false FR+ 2.99,2.75 3.281,2.906 0.292,0.156 10 false FL+ 0.292,1.281 0.646,1.531 0.354,0.25 10 false A53 1.885,1.281 2.396,1.656 0.51,0.375 10 false A16
*a Front view of wire harness connector
(to Front Speed Sensor)


Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RH
Tester Connection Condition Specified Condition
A53-1 (FR+) - Body ground Power switch on (IG) 5.7 to 14 V

for LH
Tester Connection Condition Specified Condition
A16-1 (FL+) - Body ground Power switch on (IG) 5.7 to 14 V



Result:
Proceed to
OK
NG



OK

9.RECONFIRM DTC

NG

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

9.RECONFIRM DTC
a.

Turn the power switch off.


b.

Reconnect the A53 or A16 front speed sensor connector.


c.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

d.

Turn the power switch on (READY).


e.

Perform a road test.


f.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1464/31 and/or C1465/32 are output. A
DTCs C1464/31 and C1465/32 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

10.REPLACE FRONT SPEED SENSOR

B

10.REPLACE FRONT SPEED SENSOR
a.

Turn the power switch off.



Result:
Proceed to
NEXT



NEXT

11.RECONFIRM DTC
11.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch on (READY).


c.

Perform a road test.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1464/31 and/or C1465/32 are output. A
DTCs C1464/31 and C1465/32 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

12.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY

B

END

12.REPLACE FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY
a.

Turn the power switch off.


b.

Replace the front speed sensor rotor (front drive outboard joint shaft assembly).

Click hereDrivetrain>DRIVE SHAFT / PROPELLER SHAFT>FRONT DRIVE SHAFT ASSEMBLY>DISASSEMBLY

HINT:

If the front speed sensor rotor needs to be replaced, replace the front drive outboard joint shaft assembly.


NOTICE:

Check the speed sensor signal after replacement.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>TEST MODE PROCEDURE



Result:
Proceed to
NEXT



NEXT

13.RECONFIRM DTC
13.RECONFIRM DTC
a.

Clear the DTCs.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105

b.

Turn the power switch on (READY).


c.

Perform a road test.


d.

Check if the same DTC is output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Result Proceed to
DTCs C1464/31 and/or C1465/32 are output. A
DTCs C1464/31 and C1465/32 are not output. B


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE




A

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

B

END