Home › Engine / Hybrid System › 2AR-FXE ENGINE CONTROL › SFI SYSTEM › from 2015.04
RM2040EQ _51 Engine / Hybrid System _014691 2AR-FXE ENGINE CONTROL _0074871 SFI SYSTEM J

2AR-FXE ENGINE CONTROL  SFI SYSTEM  Fuel Pump Control Circuit  


DESCRIPTION

When the engine is cranked, the start request signal output from the power management control ECU is input to the ECM, and the NE signal generated by the crankshaft position sensor is also input to the NE+ terminal. Thus, the ECM interprets that the engine has been cranked, and turns transistor Tr1 in the ECM internal circuit on. Current flows to the C/OPN (Circuit Opening) relay by turning Tr1 on. Then, the fuel pump operates.

While the NE signal is input to the ECM with the engine running, the ECM turns Tr1 on continuously.

WIRING DIAGRAM

A334845E02
5.688,1.313 6.927,1.74 1.24,0.427 10 false Power Management Control ECU 6.26,8.052 7.073,8.354 0.813,0.302 10 false ECM 2.51,7.813 3.74,8.01 1.229,0.198 10 false Fuel Pump 2.396,5.552 3.979,5.833 1.583,0.281 10 false No. 1 Integration Relay 0.708,7.896 1.271,8.333 0.563,0.438 10 false Auxiliary Battery 2.521,7.677 2.979,7.875 0.458,0.198 10 false N11 5.948,6.958 6.26,7.156 0.313,0.198 10 false FC 5.927,0.594 6.542,0.792 0.615,0.198 10 false IG2D 5.688,1.156 6.146,1.354 0.458,0.198 10 false A39 5.719,0.469 5.875,0.667 0.156,0.198 10 false 2 5.677,6.969 5.99,7.167 0.313,0.198 10 false 21 6.615,6.469 7.073,6.667 0.458,0.198 10 false Tr1 5.958,3.51 6.573,3.708 0.615,0.198 10 false MREL 5.688,3.417 6,3.615 0.313,0.198 10 false 46 0.594,6.24 1.208,6.438 0.615,0.198 10 false MAIN 1.969,7.344 2.125,7.542 0.156,0.198 10 false 4 1.979,8.271 2.135,8.469 0.156,0.198 10 false 5 1.958,7.552 2.115,7.75 0.156,0.198 10 false B 1.958,8.042 2.115,8.24 0.156,0.198 10 false E 0.927,5.01 2.917,5.208 1.99,0.198 10 false EFI-MAIN NO. 2 0.938,3.333 2.927,3.531 1.99,0.198 10 false EFI-MAIN NO. 1 1.073,1.896 2.302,2.094 1.229,0.198 10 false IG2-MAIN 3.417,2.385 3.875,2.583 0.458,0.198 10 false IG2 3.24,3.854 4.063,4.063 0.823,0.208 10 false EFI MAIN 3.208,5.188 4.031,5.396 0.823,0.208 10 false EFI MAIN2 3.313,6.854 4.083,7.052 0.771,0.198 10 false C/OPN 4.448,1.469 4.76,1.667 0.313,0.198 10 false 1C 5.021,3.521 5.333,3.719 0.313,0.198 10 false 1C 2.438,1.708 2.75,1.906 0.313,0.198 10 false 1D 2.427,4.833 2.74,5.031 0.313,0.198 10 false 1D 2.448,3.146 2.76,3.344 0.313,0.198 10 false 1B 2.438,3.521 2.75,3.719 0.313,0.198 10 false 1E 4.385,1.271 4.542,1.469 0.156,0.198 10 false 8 5.063,3.313 5.219,3.51 0.156,0.198 10 false 7 2.49,1.51 2.646,1.698 0.156,0.188 10 false 3 2.479,2.938 2.635,3.125 0.156,0.188 10 false 1 2.479,3.344 2.635,3.531 0.156,0.188 10 false 2 2.458,4.625 2.615,4.813 0.156,0.188 10 false 1 4.25,5.302 4.563,5.5 0.313,0.198 10 false 1C 4.771,5.302 5.083,5.5 0.313,0.198 10 false 1C 4.219,5.094 4.375,5.281 0.156,0.188 10 false 6 4.719,5.104 4.875,5.292 0.156,0.188 10 false 5 3.885,5.99 4.042,6.177 0.156,0.188 10 false 5 3.094,6.417 3.25,6.604 0.156,0.188 10 false 2 3.896,6.417 4.052,6.604 0.156,0.188 10 false 1 3.073,5.969 3.229,6.156 0.156,0.188 10 false 3 4.042,6.719 5.729,6.917 1.688,0.198 10 false ECU-IG2 NO. 1 5.927,8.052 6.385,8.25 0.458,0.198 10 false A25

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (CONTROL THE FUEL PUMP / SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

e.

Check whether the fuel pump operating sound occurs when performing the Active Test on the GTS.


Result:
Result Proceed to
Fuel pump operating sound does not occur A
Fuel pump operating sound occurs B



A

2.INSPECT C/OPN RELAY

B

10.READ VALUE USING GTS (STARTER COUNT)
2.INSPECT C/OPN RELAY

Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)

NG

REPLACE C/OPN RELAY

3.CHECK HARNESS AND CONNECTOR (ECM - C/OPN RELAY)
a.

Disconnect the ECM connector.


b.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A25-21 (FC) - C/OPN relay terminal 2 Always Below 1 Ω
A25-21 (FC) or C/OPN relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - NO. 1 INTEGRATION RELAY)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C/OPN relay terminal 1 - 1C-5 Always Below 1 Ω
C/OPN relay terminal 5 - 1C-6 Always Below 1 Ω
C/OPN relay terminal 1 or 1C-5 - Body ground Always 10 kΩ or higher
C/OPN relay terminal 5 or 1C-6 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (C/OPN RELAY - FUEL PUMP)
a.

Remove the C/OPN relay from the engine room relay block and junction block assembly.


b.

Disconnect the fuel pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C/OPN relay terminal 3 - N11-4 (B) Always Below 1 Ω
C/OPN relay terminal 3 or N11-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (FUEL PUMP - BODY GROUND)
a.

Disconnect the fuel pump connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N11-5 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

7.INSPECT FUEL PUMP

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT FUEL PUMP
a.

Inspect the fuel pump.

Click hereEngine / Hybrid System>2AR-FXE FUEL>FUEL PUMP>INSPECTION

HINT:

Perform "Inspection After Repair" after replacing the fuel pump.

Click hereEngine / Hybrid System>2AR-FXE ENGINE CONTROL>SFI SYSTEM>INITIALIZATION



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 1 INTEGRATION RELAY

NG

8.INSPECT NO. 1 INTEGRATION RELAY
a.

Result:
Proceed to
OK
NG



OK

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

9.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


A256530C08
0.719,1.094 1.083,1.365 0.365,0.271 0.188,0.115 0.448,0.271 0.26,0.156 10 false *a 0.813,1.156 1.135,1.323 0.323,0.167 10 false 1D
*a Front view of wire harness connector
(to No. 1 Integration Relay)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1D-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY - AUXILIARY BATTERY)

10.READ VALUE USING GTS (STARTER COUNT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Count.

Powertrain > Engine and ECT > Data List
Tester Display
Starter Count
50003 234 371

f.

Check the result when the power switch on (IG) and while cranking.

OK:
Condition Starter Count
Power switch on (IG) 0
Power switch on (READY) (while cranking) 1 or more (value changes)


Result:
Proceed to
OK
NG




OK

11.READ VALUE USING GTS (ENGINE SPEED)

NG

11.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Put the engine in inspection mode (maintenance mode).

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 236 2103

e.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

Powertrain > Engine and ECT > Data List
Tester Display
Engine Speed
50003 234 9

f.

Read the values displayed on the GTS while cranking.

OK:

Values are displayed continuously.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

CHECK CRANKSHAFT POSITION SENSOR CIRCUIT