The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the ABS warning light remains on:
The skid control ECU (brake booster with master cylinder assembly) connector is disconnected from the brake booster with master cylinder assembly.
There is a malfunction in the skid control ECU (brake booster with master cylinder assembly) internal circuit.
There is an open in the wire harness between the combination meter assembly and the skid control ECU (brake booster with master cylinder assembly).
The ABS control system is defective.
In some cases, the intelligent tester cannot be used when the skid control ECU (brake booster with master cylinder assembly) is malfunctioning.
When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION
Check if CAN communication system DTCs are output.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM
| Result | Proceed to |
|---|---|
| DTC is not output. | A |
| DTC is output. | B |
A
B
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.
The connector is securely connected.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the auxiliary battery voltage.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| Auxiliary battery | Power switch on (IG) | 11 to 14 V |
| Auxiliary battery | Power switch on (READY) | 11 to 15.5 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Disconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-16 (IG1) - Body ground | Power switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Skid Control ECU (Brake Booster with Master Cylinder Assembly)) |
Turn the power switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A28-28 (GND) - Body ground | Always | Below 1 Ω |
| A28-27 (GND2) - Body ground | Always | Below 1 Ω |
| A28-26 (GND3) - Body ground | Always | Below 1 Ω |
| A28-25 (GND4) - Body ground | Always | Below 1 Ω |
| A28-24 (GND5) - Body ground | Always | Below 1 Ω |
| A28-23 (GND6) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the A28 skid control ECU (brake booster with master cylinder assembly) connector.
Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
Check the combination meter assembly.
The ABS warning light turns on or off in accordance with intelligent tester operation.
If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.
| Proceed to |
|---|
| OK |
| NG |
OK
NG