Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM › from 2015.04
RM2040EQ _54 Brake _014708 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0074978 ELECTRONICALLY CONTROLLED BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM  Slip Indicator Light Remains ON  


DESCRIPTION

The skid control ECU (brake booster with master cylinder assembly) is connected to the combination meter assembly via CAN communication.

If the skid control ECU stores a DTC, the slip indicator light comes on in the combination meter assembly.

The slip indicator light blinks during ABS, VSC and/or TRC operation.

When the system fails, the slip indicator light comes on to warn the driver.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>DIAGNOSIS SYSTEM

WIRING DIAGRAM

C239015E22
5,3.927 7.063,4.448 2.063,0.521 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.688,3.938 5.135,4.25 0.448,0.313 10 false A28 0.417,3.917 1.594,4.406 1.177,0.49 10 false Combination Meter Assembly 0.125,3.917 0.552,4.146 0.427,0.229 10 false I18 5.969,1.135 6.573,1.427 0.604,0.292 10 false CA1L 5.969,3.135 6.469,3.448 0.5,0.313 10 false CA1H 5.698,1.042 5.99,1.313 0.292,0.271 10 false 38 5.698,3.052 6.01,3.313 0.313,0.26 10 false 37 0.885,1.135 1.438,1.427 0.552,0.292 10 false CANL 0.885,3.125 1.448,3.385 0.563,0.26 10 false CANH 1.396,1.042 1.76,1.271 0.365,0.229 10 false 16 1.396,3.042 1.813,3.271 0.417,0.229 10 false 17

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake booster with master cylinder assembly), perform initialization and calibration of the linear solenoid valve.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>INITIALIZATION


PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM


Result:
Result Proceed to
DTC is not output. A
DTC is output. B



A

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED

B

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake booster with master cylinder assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK AUXILIARY BATTERY

NG

CONNECT CONNECTOR TO SKID CONTROL ECU CORRECTLY

3.CHECK AUXILIARY BATTERY
a.

Check the auxiliary battery voltage.

Standard Voltage:
Tester Connection Condition Specified Condition
Auxiliary battery Power switch on (IG) 11 to 14 V
Auxiliary battery Power switch on (READY) 11 to 15.5 V



Result:
Proceed to
OK
NG



OK

4.INSPECT COMBINATION METER ASSEMBLY

NG

CHARGE OR REPLACE AUXILIARY BATTERY

4.INSPECT COMBINATION METER ASSEMBLY
a.

Perform the Active Test of the combination meter assembly (meter CPU) using the intelligent tester.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST


b.

Check the combination meter assembly.

OK:

The slip indicator light turns on or off in accordance with intelligent tester operation.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing the part.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE BOOSTER WITH MASTER CYLINDER ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY