Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART ENTRY AND START SYSTEM(for Start Function) › from 2015.04
RM2040EQ _58 Vehicle Interior _014723 THEFT DETERRENT / KEYLESS ENTRY _0075054 SMART ENTRY AND START SYSTEM(for Start Function) C

THEFT DETERRENT / KEYLESS ENTRY  SMART ENTRY AND START SYSTEM(for Start Function)  B2285  Steering Lock Position Signal Circuit Malfunction  


DESCRIPTION

This DTC is stored when the steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication do not match.

HINT:

When the cable is disconnected and reconnected to the negative (-) auxiliary battery terminal, the power source mode returns to the state it was in before the cable was disconnected.


DTC No. Detection Item DTC Detection Condition Trouble Area Note
B2285 Steering Lock Position Signal Circuit Malfunction The steering lock position signal sent by the steering lock ECU (steering lock actuator assembly) via direct line and the steering lock position signal sent via LIN communication (1-trip detection logic*) do not match.
·

AM2 fuse

·

Steering lock ECU (steering lock actuator assembly)

·

Power management control ECU

·

Wire harness or connector


DTC Output Confirmation Operation

Disconnect the cable from the negative (-) auxiliary battery terminal, wait 30 seconds and then reconnect the cable to the negative (-) auxiliary battery terminal. Wait 40 seconds or more with the power switch off (with the steering wheel locked), then turn the power switch on (ACC) (with the steering unlocked) and wait 40 seconds or more.



*: Only detected while a malfunction is present and the power switch is on (IG)


Vehicle Condition and Fail-safe Function when Malfunction Detected
Vehicle Condition when Malfunction Detected Fail-safe Function when Malfunction Detected
The hybrid control system cannot be started. The ECU does not send an hybrid control system start request.

WIRING DIAGRAM

B293339E16
0.74,1.771 1.021,1.948 0.281,0.177 10 false I24 0.51,2.375 2.323,2.552 1.813,0.177 10 false :LIN Communication Line 2.948,0.406 3.281,0.583 0.333,0.177 10 false AM2 1.021,1.771 2.833,2.135 1.813,0.365 10 false Steering Lock ECU (Steering Lock Actuator Assembly) 4.25,1.813 5.531,2.219 1.281,0.406 10 false Power Management Control ECU 2.615,1.375 2.708,1.531 0.094,0.156 10 false 4 2.167,1.438 2.604,1.615 0.438,0.177 10 false SLP1 5.073,0.26 5.51,0.406 0.438,0.146 10 false E01 5.51,0.073 5.625,0.219 0.115,0.146 10 false 5 5.49,0.26 5.76,0.448 0.271,0.188 10 false I3 5.073,0.656 5.51,0.802 0.438,0.146 10 false E02 5.51,0.469 5.625,0.615 0.115,0.146 10 false 5 5.5,0.656 5.771,0.844 0.271,0.188 10 false I4 5.146,1.042 5.583,1.188 0.438,0.146 10 false E1 5.49,0.875 5.604,1.021 0.115,0.146 10 false 6 5.479,1.052 5.75,1.24 0.271,0.188 10 false I3 5.063,1.448 5.5,1.594 0.438,0.146 10 false E12 5.5,1.271 5.615,1.417 0.115,0.146 10 false 4 5.49,1.458 5.76,1.646 0.271,0.188 10 false I4 1.552,0.26 2.417,0.573 0.865,0.313 10 false from Auxiliary Battery 4.448,0.26 4.885,0.406 0.438,0.146 10 false AM21 4.167,0.104 4.281,0.25 0.115,0.146 10 false 7 4.146,0.271 4.354,0.458 0.208,0.188 10 false I4 4.448,0.667 4.885,0.813 0.438,0.146 10 false AM22 4.167,0.49 4.281,0.635 0.115,0.146 10 false 1 4.146,0.677 4.417,0.865 0.271,0.188 10 false I3 4.146,0.885 4.323,1.031 0.177,0.146 10 false 11 4.167,1.052 4.375,1.24 0.208,0.188 10 false I4 4.146,1.281 4.396,1.427 0.25,0.146 10 false 12 4.167,1.458 4.438,1.646 0.271,0.188 10 false I4 4.448,1.448 4.885,1.594 0.438,0.146 10 false SLP 4.458,1.073 4.896,1.219 0.438,0.146 10 false LIN2 2.594,0.927 2.688,1.083 0.094,0.156 10 false 5 2.281,1.073 2.635,1.25 0.354,0.177 10 false LIN

CAUTION / NOTICE / HINT

NOTICE:
·

When using the intelligent tester with the power switch off, perform either of the following: 1) Turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the intelligent tester and vehicle begins, or 2) connect the intelligent tester to the vehicle, select the vehicle type under manual mode, and then enter the following menus:

for Power Source Control: Body / Power Source Control / DTC.

for Entry&Start: Body / Entry&Start / DTC.

·

The smart entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before replacing the steering lock ECU (steering lock actuator assembly), refer to the smart entry and start system (for Start Function) precaution (See page Vehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>SMART ENTRY AND START SYSTEM(for Start Function)>PRECAUTION).

·

Before replacing the power management control ECU, refer to the Service Bulletin.

·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After performing repairs, perform the operation that fulfills the DTC output confirmation operation, and then confirm that no DTCs are output again.



HINT:
Related Data List and Active Test Items
DTC Data List Item Active Test Item
B2285
Power Source Control

Steering Unlock Switch


Entry&Start
·

Power Supply Short

·

Motor Driver Short

·

Lock Bar Stuck Error


-


PROCEDURE

1.CHECK FOR DTC (LIN COMMUNICATION SYSTEM)
a.

Check for DTCs.

Click herePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>DTC CHECK / CLEAR

Body Electrical > Power Source Control > Trouble Codes
50001 223
OK:

LIN communication system DTC B2785 is not output simultaneously.


HINT:
·

If the steering wheel cannot be locked or unlocked, the power switch cannot be turned on (IG) and the hybrid control system cannot be started.

·

If LIN communication is not available, the steering wheel cannot be locked or unlocked.




Result:
Proceed to
OK
NG



OK

2.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)

NG

2.READ VALUE USING INTELLIGENT TESTER (STEERING UNLOCK SWITCH)
a.

Connect the intelligent tester to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the intelligent tester on.


d.

Enter the following menus: Body / Power Source Control / Data List.


e.

According to the display on the intelligent tester, read the Data List.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Steering Unlock Switch Switch State of steering unlock sensor signal output from steering lock actuator assembly ON or OFF ON: Steering unlocked
OFF: Steering locked
·

When the shift lever is in P and the power switch is off, if any door is opened or closed, the steering is locked.

·

When the electrical key transmitter sub-assembly is inside the vehicle and the power switch is turned on (ACC) or on (IG), the steering unlocks.

·

The hybrid control system cannot be started when the steering unlock signal is off.


Body Electrical > Power Source Control > Data List
Tester Display
Steering Unlock Switch
50003 223 2

Result:
Result Proceed to
Data List item does not change A
Data List item changes B



A

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

B

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE)

OK

4.CHECK HARNESS AND CONNECTOR (GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE

4.CHECK HARNESS AND CONNECTOR (GROUND)

OK

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.INSPECT STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)
a.
C197722C46
0.25,0.594 0.698,0.833 0.448,0.24 1.156,1.948 1.333,1.948 1.333,1.948 1.719,1.177 false 0.802,1.875 1.167,2.063 0.365,0.188 10 false SLP1 0.104,0.021 0.344,0.208 0.24,0.188 10 false *a 0.354,0.635 0.646,0.792 0.292,0.156 10 false I24
*a Component with harness connected(Steering Lock ECU (Steering Lock Actuator Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive (+) tester probe → I24-4 (SLP1)
Negative (-) tester probe → Body ground
Steering locked* 10 kΩ or higher
Steering unlocked* Below 1 Ω


HINT:
·

*: If any of the doors are opened then closed with the shift lever in P and the power switch off, the steering wheel will be locked. If the power switch is then turned on (ACC) or on (IG), the steering wheel will be unlocked.

·

DTC B2285 may be stored due to a malfunction in the steering lock ECU (steering lock actuator assembly). The steering lock position signal and unlock position signal are sent from the steering lock ECU (steering lock actuator assembly) to the power management control ECU individually.




Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))

NG

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY)

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY))
a.

Disconnect the I4 connector from the power management control ECU.


b.

Disconnect the I24 connector from the steering lock ECU (steering lock actuator assembly).


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I4-12 (SLP) - I24-4 (SLP1) Always Below 1 Ω
I4-12 (SLP) or I24-4 (SLP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR