DTC P0171 System Too Lean (Bank 1) |
DTC P0172 System Too Rich (Bank 1) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0171 | With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the lean side (2 trip detection logic). |
|
| P0172 | With a warm engine and stable air fuel ratio feedback, the fuel trim is considerably in error to the rich side (2 trip detection logic). |
|

| Required Sensors/Components | Air fuel ratio sensor Mass air flow meter sub-assembly Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Fuel system status | Closed loop |
| Auxiliary battery voltage | 11 V or higher |
| Either of the following conditions is met | 1 or 2 |
| 1. Engine speed | Less than 1100 rpm |
| 2. Engine load | 10% or higher |
| Purge-cut | Executing |
| Either of the following conditions is met | 1 or 2 |
| 1. Average between short-term fuel trim and long-term fuel trim | 35% or higher (varies with engine coolant temperature) |
| 2. Average between short-term fuel trim and long-term fuel trim | -35% or less (varies with engine coolant temperature) |

| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0171 OR P0172) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0171 or P0172 is output | A |
| DTC P0171 or P0172 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections (Click here).
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 4.PERFORM ACTIVE TEST USING GTS (CONTROL THE INJECTION VOLUME FOR A/F SENSOR) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Idle the engine for 5 minutes or more with the shift lever in P.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / All Data / AFS Voltage B1S1 and O2S B1S2.
Perform the Control the Injection Volume for A/F Sensor operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
Monitor the voltage outputs of the air fuel ratio sensor and the heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2) displayed on the GTS.
| GTS Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 (Air fuel ratio) | 12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 (Heated oxygen) | 12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status AFS Voltage B1S1 | Status O2S B1S2 | Air Fuel Ratio Condition and Air Fuel Ratio Sensor Condition | Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal | - | A |
| Lean | Lean | Actual air fuel ratio lean |
| A |
| Rich | Rich | Actual air fuel ratio rich |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction |
| B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction |
| B |
|
| ||||
| A | |
| 5.READ VALUE USING GTS (COOLANT TEMP) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the Data List twice, when the engine is both cold and warmed up.
| GTS Display | Condition | Specified Condition |
| Coolant Temp | Cold engine | Same as ambient air temperature |
| Warm engine | Between 75 and 100°C (167 and 212°F) |
|
| ||||
| OK | |
| 6.READ VALUE USING GTS (MAF) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.
Allow the engine to idle until Coolant Temp reaches 75°C (167°F) or higher.
Read MAF with the engine speed at 2500 rpm.
| GTS Display | Condition | Specified Condition |
| MAF | Shift lever position: N A/C: Off Engine Speed: 2500 rpm | Between 5.0 gm/sec and 9.0 gm/sec |
|
| ||||
| OK | |
| 7.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 8.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks.
|
| ||||
| OK | |
| 9.CHECK FOR SPARK (SPARK TEST) |
Perform a spark test .
| NEXT | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME) |
Check the injection and volume.
|
| ||||
|
| ||||
| 11.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
Inspect the air fuel ratio sensor (Click here).
|
| ||||
| OK | |
| 12.CHECK TERMINAL VOLTAGE (POWER SOURCE OF AIR FUEL RATIO SENSOR) |
![]() |
Disconnect the air fuel ratio sensor connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E19-2 (+B) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector (to Air Fuel Ratio Sensor) |
|
| ||||
| OK | |
| 13.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM) |
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E19-1 (HA1A) - E28-23 (HA1A) | Always | Below 1 Ω |
| E19-3 (A1A+) - E28-133 (A1A+) | Always | Below 1 Ω |
| E19-4 (A1A-) - E28-134 (A1A-) | Always | Below 1 Ω |
| E19-1 (HA1A) or E28-23 (HA1A) - Body ground | Always | 10 kΩ or higher |
| E19-3 (A1A+) or E28-133 (A1A+) - Body ground | Always | 10 kΩ or higher |
| E19-4 (A1A-) or E28-134 (A1A-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 14.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 15.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0171 or P0172 is output | A |
| DTCs are not output | B |
|
| ||||
| A | |
| 16.PERFORM ACTIVE TEST USING GTS (CONTROL THE EGR STEP POSITION) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the EGR Step Position / Data List / All Data / MAP and Throttle Idle Position.
Confirm that Throttle Idle Position is ON and check the MAP value in the Data List while performing the Active Test.
| - | EGR Step Position (Active Test) | |
| 0 Steps | 0 to 30 Steps | |
| MAP (Data List) | (EGR valve is fully closed) | MAP value is at least +10 kPa (75 mmHg) higher than when EGR valve is fully closed |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 17.INSPECT EGR VALVE ASSEMBLY |
Remove the EGR valve assembly (Click here).
Check if the EGR valve is stuck open.
|
| ||||
| OK | |
| 18.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY CONNECTOR CONNECTION) |
Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter sub-assembly and ECM (Click here).
| NEXT | |
| 19.CHECK WHETHER DTC OUTPUT RECURS (DTC P0171 OR P0172) |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P0171 or P0172 is output | A |
| DTCs are not output | B |
|
| ||||
| A | |
| 20.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E14-4 (E2G) - E28-92 (E2G) | Always | Below 1 Ω |
|
| ||||
| OK | |
| 21.REPLACE MASS AIR FLOW METER SUB-ASSEMBLY |
Replace the mass air flow meter sub-assembly (Click here).
| NEXT | |
| 22.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Turn the GTS on.
Clear the DTCs (Click here).
Turn the power off and wait for at least 30 seconds.
Turn the power switch on (IG).
Turn the GTS on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTCs are not output | A |
| DTC P0171 or P0172 is output | B |
|
| ||||
| A | ||
| ||
| 23.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - NO. 1 INTEGRATION RELAY) |
Disconnect the air fuel ratio sensor connector.
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E19-2 (+B) - 1A-7 | Always | Below 1 Ω |
| E19-2 (+B) or 1A-7 - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 24.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY) |
![]() |
Remove the No. 1 integration relay from the engine room relay block and junction block assembly.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1D-1 - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector (to No. 1 Integration Relay) |
|
| ||||
| OK | ||
| ||