DTC P3190 Poor Engine Power |
DTC P3191 Engine does not Start |
DTC P3193 Fuel Run Out |
| DTC No. | DTC Detection Condition | Trouble Area |
| P3190 | Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic):
|
|
| P3191 | Following conditions continue at a fixed engine speed or a fixed length of time (1 trip detection logic):
|
|
| P3193 | Fuel low level signal input into ECM (1 trip detection logic). |
|
| Frequency of Operation | Continuous |
| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P3190, P3191 AND/OR P3193) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P3190, P3191 and/or P3193 are output | A |
| DTC P3190, P3191 and/or P3193 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK SHORTAGE OF FUEL |
Check the amount of fuel remaining.
|
| ||||
| OK | |
| 3.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks (Click here).
|
| ||||
| OK | |
| 4.CHECK FOR UNUSUAL NOISE OR VIBRATION WHEN STARTING ENGINE OR REVVING UP |
|
| ||||
| OK | |
| 5.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 6.INSPECT FREEZE FRAME DATA |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC / Freeze Frame Data.
Calculate the requested torque* and compare it with Actual Engine Torque.
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 7.INSPECT THROTTLE WITH MOTOR BODY ASSEMBLY |
Inspect the throttle with motor body assembly (Click here).
|
| ||||
| OK | |
| 8.INSPECT MASS AIR FLOW METER SUB-ASSEMBLY |
Inspect the mass air flow meter sub-assembly (Click here).
|
| ||||
| OK | |
| 9.INSPECT ENGINE COOLANT TEMPERATURE SENSOR |
Inspect the engine coolant temperature sensor (Click here).
|
| ||||
| OK | |
| 10.INSPECT CRANKSHAFT POSITION SENSOR |
Inspect the crankshaft position sensor (Click here).
|
| ||||
| OK | |
| 11.REPLACE CAMSHAFT POSITION SENSOR |
Replace the camshaft position sensor (Click here).
| NEXT | |
| 12.CHECK WHETHER DTC OUTPUT RECURS (DTC P3190, P3191 AND/OR P3193) |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Allow the engine to idle for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the pending DTCs.
| Result | Proceed to |
| DTC P3190, P3191 and/or P3193 is output | A |
| DTC is not output | B |
|
| ||||
| A | |
| 13.REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 14.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Turn the power switch on (IG).
Turn the tester on.
Clear the DTCs (Click here).
Turn the power switch off and wait for at least 30 seconds.
Turn the power switch on (IG) and turn the tester on.
Put the engine in inspection mode (maintenance mode) (Click here).
Start the engine.
Allow the engine to idle for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P3190, P3191 or P3193.
Check the DTC judgment result.
| NEXT | ||
| ||