DTC C1430 Brake Pedal Load Sensing Switch OFF Stuck Malfunction |
DTC C1431 Brake Pedal Load Sensing Switch ON Stuck Malfunction |
| DTC No. | DTC Detection Condition | Trouble Area |
| C1430 | Either of the following is detected:
|
|
| C1431 | Either of the following is detected:
|
|
| 1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH ASSEMBLY AND BRAKE PEDAL LOAD SENSING SWITCH) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| Brake Pedal Load Sensing SW | Brake pedal load sensing switch / ON or OFF | ON: Brake pedal depressed beyond a specified point OFF: Brake pedal not depressed beyond a specified point | - |
Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to brake pedal operation.
Slowly depress the brake pedal, and check when the stop light switch and brake pedal load sensing switch turn on.
| Result | Proceed to |
| OK | A |
| NG (Turning on of the brake pedal load sensing switch is not confirmed.) | B |
| NG (The brake pedal load sensing switch turns on first.) | C |
|
| ||||
|
| ||||
| A | |
| 2.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Perform a road test.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1430 and C1431 are not output. | A |
| DTCs C1430 and/or C1431 are output. | B |
|
| ||||
| A | ||
| ||
| 3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH |
![]() |
Turn the ignition switch off.
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the brake pedal load sensing switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (FSW+) - 1 (FSW-) | Switch OFF (Brake pedal depressed) | 950 to 1050 Ω |
| 2 (FSW+) - 1 (FSW-) | Switch ON (Brake pedal released) | 203 to 223 Ω |
| *a | Component without harness connected (Brake Pedal Load Sensing Switch (Brake Pedal Support Assembly)) |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH) |
Make sure that there is no looseness at the locking part and the connecting part of the connector.
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-34 (FSW+) - A40-2 (FSW+) | Always | Below 1 Ω |
| A49-34 (FSW+) - Body ground | Always | 10 kΩ or higher |
| A40-1 (FSW-) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION |
Turn the ignition switch off.
Check the brake pedal height and stop light switch assembly installation (Click here for LHD or Click here for RHD).
| Result | Proceed to |
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||