VEHICLE STABILITY CONTROL SYSTEM > Brake Warning Light Remains ON |

| 1.CHECK CAN COMMUNICATION SYSTEM |
Check if a CAN communication system DTC is output (Click here).
| Result | Proceed to |
| DTC is not output. | A |
| DTC is output. | B |
|
| ||||
| A | |
| 2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check if the skid control ECU connector is securely connected.
|
| ||||
| OK | |
| 3.CHECK BATTERY |
Check the battery voltage.
| Result | Proceed to |
| OK | A |
| NG (for 2GR-FE) | B |
| NG (for 2AR-FE) | C |
| NG (for 6AR-FSE) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL) |
![]() |
Disconnect the skid control ECU connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-25 (+BS) - Body ground | Always | 11 to 14 V |
| A49-25 (+BS) - A49-38 (GND1) | Always | 11 to 14 V |
| A49-28 (IG1) - Body ground | Ignition switch ON | 11 to 14 V |
| A49-28 (IG1) - A49-38 (GND1) | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL) |
![]() |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A49-38 (GND1) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Skid Control ECU (Brake Actuator Assembly)) |
|
| ||||
| OK | |
| 6.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SWITCH ASSEMBLY) |
Reconnect the skid control ECU connector.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Parking Brake SW | Parking brake switch / ON or OFF | ON: Parking brake applied OFF: Parking brake released | - |
Using the intelligent tester, check the switch operation signal received when the parking brake is operated.
|
| ||||
| OK | |
| 7.INSPECT BRAKE FLUID LEVEL WARNING SWITCH |
![]() |
Turn the ignition switch off.
Remove the reservoir filler cap and the strainer.
Disconnect the brake fluid level warning switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (+) - 2 (E) | Switch OFF (Float up) | 1.9 to 2.1 kΩ |
| 1 (+) - 2 (E) | Switch ON (Float down) | Below 1 Ω |
| *a | Component without harness connected (Brake Fluid Level Warning Switch (Brake Master Cylinder Reservoir Sub-assembly)) |
| Result | Proceed to |
| OK (except 6AR-FSE) | A |
| OK (for 6AR-FSE) | B |
| NG (for LHD) | C |
| NG (for RHD) | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 8.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-9 (SW) - A30-1 (+) | Always | Below 1 Ω |
| I18-9 (SW) - Body ground | Always | 10 kΩ or higher |
| A30-2 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 9.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT) |
Reconnect the brake fluid level warning switch connector.
Reconnect the combination meter assembly connector.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Brake Warning Light | Brake warning light / ON or OFF | ON: Warning light on OFF: Warning light off | - |
Check the intelligent tester display condition of the brake warning light.
| Result | Proceed to |
| ON is displayed. | A |
| OFF is displayed. | B |
|
| ||||
| A | ||
| ||
| 10.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BRAKE FLUID LEVEL WARNING SWITCH) |
Disconnect the vacuum warning switch assembly connector.
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-9 (SW) - A30-1 (+) | Always | Below 1 Ω |
| I18-9 (SW) - Body ground | Always | 10 kΩ or higher |
| A30-2 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 11.INSPECT VACUUM WARNING SWITCH ASSEMBLY |
Reconnect the brake fluid level warning switch connector.
Reconnect the vacuum warning switch assembly connector.
Reconnect the combination meter assembly connector.
Inspect the vacuum warning switch assembly (Click here).
|
| ||||
| OK | |
| 12.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - VACUUM WARNING SWITCH ASSEMBLY) |
Disconnect the brake fluid level warning switch connector.
Disconnect the vacuum warning switch assembly connector.
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| I18-6 (VSW) - A85-2 (+) | Always | Below 1 Ω |
| I18-6 (VSW) - Body ground | Always | 10 kΩ or higher |
| A85-1 (E) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 13.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT) |
Reconnect the brake fluid level warning switch connector.
Reconnect the vacuum warning switch assembly connector.
Reconnect the combination meter assembly connector.
Turn the ignition switch to ON.
Select the Data List using the intelligent tester (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| Brake Warning Light | Brake warning light / ON or OFF | ON: Warning light on OFF: Warning light off | - |
Check the intelligent tester display condition of the brake warning light.
| Result | Proceed to |
| ON is displayed. | A |
| OFF is displayed. | B |
|
| ||||
| A | ||
| ||
| 14.INSPECT PARKING BRAKE SWITCH ASSEMBLY |
![]() |
Turn the ignition switch off.
Disconnect the parking brake switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 1 (+) - Body ground | Parking brake switch ON (Switch pin free) | Below 1 Ω |
| 1 (+) - Body ground | Parking brake switch OFF (Switch pin pushed in) | 10 kΩ or higher |
| *a | Component without harness connected (Parking Brake Switch Assembly) |
| Result | Proceed to |
| OK | A |
| NG (for LHD) | B |
| NG (for RHD) | C |
|
| ||||
|
| ||||
| A | |
| 15.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - PARKING BRAKE SWITCH ASSEMBLY) |
Disconnect the main body ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3D-20 (PKB) - A42-1 (+) | Always | Below 1 Ω |
| 3D-20 (PKB) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||