DTC P07457F Pressure Control Solenoid "A" Actuator Stuck Off |
| DTC No. | DTC Detection Condition | Trouble Area |
| P07457F | 1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other DTC Detection Condition 1:
DTC Detection Condition 2:
|
|
| 1.CHECK OTHER DTCS OUTPUT (IN ADDITION TO DTC P07457F) |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Trouble Codes.
Read the DTCs using the GTS.
| Result | Proceed to |
| Only DTC P07457F is output | A |
| DTC P07457F and other DTCs are output | B |
|
| ||||
| B | |
| 2.PERFORM ACTIVE TEST USING GTS (CONTROL THE SHIFT POSITION) |
Warm up the engine.
Turn the engine switch off.
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Powertrain / Transmission / Active Test / Control the Shift Position.
Perform the Active Test according to the display on the GTS.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operates the shift solenoid valves to allow gears to be selected manually |
| Can be used to check the operation of the shift solenoid valves. Upshifts and downshifts should be performed consecutively. A 10-second interval is required between gear changes. Do not downshift at high speeds. Doing so will damage the automatic transaxle. [Vehicle Condition]
|
Check the vehicle speed and gear when the engine speed is 1000 rpm.
| 1st | 2nd | 3rd | 4th | 5th | 6th |
| 8 to 12 km/h (5 to 7 mph) | 15 to 19 km/h (9 to 12 mph) | 21 to 25 km/h (13 to 16 mph) | 31 to 35 km/h (19 to 22 mph) | 44 to 48 km/h (27 to 30 mph) | 52 to 56 km/h (32 to 35 mph) |
Compare the ECM commanded gear and the actual gear.
| Actuator Gear during Malfunction | ECM Commanded Gear | Proceed to | ||||||
| 1st | 2nd | 3rd | 4th | 5th | 6th | |||
| Shift solenoid valve SL1 | Stuck ON | 1st | 2nd | 3rd | 4th | 4th | 4th | A |
| Stuck OFF | N*1 | N*1 | N*1 | N*1 | 5th | 6th | ||
| Shift solenoid valve SL2 | Stuck ON | 4th | 4th | 4th | 4th | 5th | 6th | B |
| Stuck OFF | 1st | 2nd | 3rd | 1st | N*1 | N*1 | ||
| Shift solenoid valve SL3 | Stuck ON | 2nd | 2nd | 3rd | 4th | 5th | 6th | C |
| Stuck OFF | 1st | 1st | 3rd | 4th | 5th | N*1 | ||
| Shift solenoid valve SL4 | Stuck ON | 3rd | 3rd | 3rd | 4th | 5th | 5th | D |
| Stuck OFF | 1st | 2nd | 1st | 4th | N*1 | 6th | ||
| Shift solenoid valve SLT | Stuck ON | N*2 | N*2 | N*2 | N*2 | N*2 | N*2 | E |
| Stuck OFF*3 | 1st | 2nd | 3rd | 4th | 5th | 6th | ||
|
| ||||
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.INSPECT SHIFT SOLENOID VALVE SL1 |
![]() |
Remove the shift solenoid valve SL1.
| *1 | Shift Solenoid Valve SL1 |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 5.0 to 5.6 Ω |
Connect a positive (+) lead from the battery with a 21 W bulb to terminal 2 and a negative (-) lead to terminal 1 of the solenoid valve connector. Check that the valve moves and makes an operating sound.
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
|
| ||||
| OK | ||
| ||